This degree project aims at developing a concept for how to use solar energy to pump up water. The target audience is people living in areas where the functioning of the electricity and water network is absent. In these areas, the hand-powered water pump is the most common technology. The degree project's goal is to find an economically viable alternative to the time consuming hand-powered water pumps. The power comes from solar energy.

This thesis is the result of the investigation and solution of a mechanicalproblem regarding flywheel malfunctions. A flywheel is, in short, a devicethat relies on a rotating object?s moment of inertia to store energy overshort time spans. This project is part of the development of a fourthflywheel prototype at the division for electricity at Uppsala university,which uses magnetic levitation to keep a hollow cylinder rotating at veryhigh speeds inside a vacuum chamber. Should the magnets fail however, orsome other error occur that leads to an uncontrolled state of rotation, thecylinder needs to be stabilized mechanically by a device usually referredto as ?back-up bearing?.

This study was done regarding whether sealing or ventilation is the best solution to prevent moisture on cold attics. The authors of this report addressed the problem with moisture in attics when they started their cooperation with Peab.The methods included interviews with people, database research, and calculations of a project in Akersberga north of Stockholm. The conclusion is based on interviews and other information as they are analyzed in relation to the house of reference. The focus of this report is on problems with moisture in the attics known as cold attics.The background of the problem with moisture is that today?s slabs are usually insulated to save energy and that the attics nearly gives the climate as the outdoor climate.

As a part of the fight against the global warming the energy production needs to be more efficient and redirected towards sustainable options. One alternative is cogeneration, which means that electricity and heat is produced in one plant. The purpose with this survey is to examine if there are any commercial available combined heat and power techniques, based on combustion of solid moist biomass, which are suitable to small-scale applications. The technique must be able to produce between 2 and 10 MW thermal and the heat demand is a Swedish district-heating system. When already published reports had been studied, the Organic Rankine Cycle (ORC) was chosen as the most suitable technique.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

Idag står bostads- och servicesektorn för närmare 40 % av Sveriges totala slutliga energianvändning. Flerbostadshus utgör ca 30 % av den energianvändningen. Därför är det viktigt att lokalisera energiparametrar och redovisa dess betydelse för energianvändningen. Samtidigt bör relationen mellan energianvändning och inomhusklimat analyseras, så att inte förändringar i energin medför till försämringar för inomhusklimatet. Baserat på identifiering hos energisparpotentialen hos parametrar, parameterbeteende och parameterkänslighet för energianvändning har i studien ett antal parametrar undersökts för ett flerbostadshus.

With higher prices for oil and increased focus on fossil fuels impact on the environment the heating sector are searching for alternative fuels. Pellets are a quite new product whose production has risen exponential in recent years. Today there are small-, medium-and large-scale users, where the large-scale consumers are the heating sector. The heating sector is mainly using oil to cover the increased demand during cold periods. The purpose of this study is to analyze the potential of pellets if it would replace thermal power plants oil and coal. The study will also analyze the economic impact a conversion would mean for a heating plant and if the pellet is a reasonable substitute. 2008 statistics from the Swedish district heating association were analyzed and a calculation was performed to determine how many tons of pellets is needed to replace coal and oil.

The aims of this project were to describe the circumstances around dogs being left alone in cars, to investigate owners? knowledge of the risks associated with leaving dogs in cars and the relevant legislation and, finally, to study how changes in the air temperature and air composition in the car affect the dog. The project consisted of a survey of the literature, a questionnaire part and an experimental part. An important conclusion is the importance of the level of knowledge of owners, since there are several ways in which an owner can prevent their dog from heat stroke and, in the case of an eventual accident, their action can have direct consequences in minimizing the long-term damage to the dog and even whether or not it survives. Fewer than half of the owners in the study knew that for a dog suffering heat stroke, the most important thing is to bring the body temperature down. Only a third of dog owners knew that if a dog is left in a warm car and showing signs of heat stress, then the police should be contacted and the dog quickly helped out of the car.

Throughout its wide distribution in the northern hemisphere, the golden eagle occurs in a diverse range of environments, e.g., mountainous, forest and open areas. The literature on juvenile golden eagles is limited, and this study provides further knowledge on habitat use and ranging behaviour during the post-fledging period in boreal Sweden. A total of 14 golden eagle juveniles were tagged with GPS transmitters during 2010 and 2011, and nine could be followed during the entire post-fledging period from fledging until migration. The juveniles fledged at the end of July and beginning of August and initiated migration during October and beginning of November. The length of the post-fledging period, until migration started, ranged from 49 to 97 days. During this period, the juveniles? distance from their natal nest and their GPS height increased with time as their flying abilities developed.

The aim of this thesis is to develop a new business model for district heating and cooling firms which can contribute to a stabilization of the Swedish national energy system. The business model is developed for a district heating and cooling firm and is exemplified with Fortum Heat. The theoretical investigation around the topic creates a rigid base for following qualitative empirical studies. Osterwalder?s canvas for business model generation is used together with a Casual Loop Diagram to identify a number of business opportunities which stabilizes the national energy system.

ur society is today in a phase of development in environmental and sustainable thinking. Alarming reports show changes in climate caused by our load and exhaust of resources. The energy usage contributes to a big part of it, by its emission of carbon dioxide. The built environment uses around 40 % of the total energy consumption in Sweden and requests to strongly reduce it are presented from both EU and national level.This thesis brings up the subject of green building with a focus on how we can create more energy efficient buildings in projects of new construction. Since the construction industry today often fails to pass on the knowledge between different projects, as a return of experiences, the construction company Skanska suggested the topic for this thesis.

AbstractWith increasing population and increasing demands for comfort and thus an increase in energy demand, it is necessary to examine various energy-efficiency measures. This work deals with the ability to control the flow through the heating system to achieve the desired comfort with as little energy as possibleA heating system contains of different parts, roughly speaking, you can divide it to three main components: Heat source, Distribution and Heat emitters. All components are working together to bring heat to the building. What is examined in this report are different ways of adjusting the flow and supply temperature and how it affects comfort and energy use in a building.At today ?s date the conventional method is to use a high flow through the heating system, which affects pressure drop and cooling of the fluid.

The production of cheese is in continuous development with objectives to in-crease productivity, achieve changes in shelf life and functional properties of the products. One concept in the development is to substitute milk fat with vegetable fats and oils in the manufacture of cheese. The objective of this study was to investigate effects on cheese yield and cheese quality of 4 different semi-hard analogue cheese products produced by substituting milk fat with vegetable fat, each analogue cheese with a specific mixture of vegeta-ble fat. As reference a cheese produced with anhydrous milk fat was used. The yield and recovery of fat and protein were determined by recording the weights of each cheese direct after press and after 20±2 days of storage and analysis of the composition of the cheeses after 20±2 days of storage. The cheese was fur-ther subjected for texture profile analysis in a TA-XT Plus Texture Analyser and analysed with Differential Scanning Calorimetry (DSC) to examine whether the fat behaves similar in the cheese as in pure form in respect to its thermal properties. The cheese yield was not significantly different when using different fats. Differ-ent amounts of water were absorbed during the water cooling.

The housing sector uses 40 % of the energy in Sweden and half of the electricity usage. Theuse of energy is the main reason to the increasing rate of carbon dioxide in the atmosphere.This is the main motive but also a wish of higher safety, that is a higher rate of selfsufficientenergy production in Sweden, we want to decrease the need of using fossil fuel. Now whenthe energy price rise, the interest in energy issues increase and more people discuss thepossibility of reducing the usage of fossil fuel. A change to renewable energy such as sun,wind and water is the only solution where we can get a sustainable development.One way to contribute to a better use of energy is to build in the principle of passive house.The house is being built with a thick and tight insulation. If you use a heat-exchanger withhigh degree of efficiency and a final heating battery on the ventilation system, the heat fromlamps, devices and the ones living in the house should be enough to fulfil the criteria ofliving.

Energy price are on the way up to a high level that will not diminish in the future make us to focus more on the sustainable development for a better solution of residential houses. Passive house or low energy housing are one of the solution to make residential more environment friendly, in same time it´s a financial security using less energy, and saving money. The last 10 years in Germany and all around Europe the concept of passive house been developed, and people aim to know more about these concept that leading the market more attractive for passive houses. A passive house is a well designed building highly insulated and air tight with mechanical ventilated system for the whole building envelope that minimizes the use of energy for heating [1].The housing company Mimer has chosen to invest in low energy consumption in every new housing project.  These future plan projects are decided to use less than 75 kwh per square meter annually in purchased energy [2].This thesis is about new constructed passive houses, and focuses on the evaluations of the temperature, and moisture condition for attic, external walls and joist.