The dry out criterion (MCPR) has been calculated for the most limiting H2-events for Forsmarks unit 2 and 3, at operating points that are normally not analyzed before each cycle. The operating points that normally are regarded as the ones with the lowest margin to dry out are the ones where the thermal power is the highest at agiven recirculation flow. This report shows that this is not the case for Forsmark 3. MCPR-values at partial power operating points are higher for the limiting case inside rather than on the boundary of the region of operation. It is therefore recommended that the method for determining the dry out criterion for Forsmark 3 is revised to account for this effect.

To establish good horse welfare there are several factors that need to be considered. One important factor is the environment in which the horses are kept. In Sweden horses are stabled during long periods of time in the cold season and consequently the stable environment is even more important. The most essential environmental factors in a horse stable are ambient temperature, relative humidity (RH) and concentrations of contaminants in the stable air. The air in a horse stable contains dust, noxious gases, moulds and microorganisms which all can contribute to developing respiratory diseases in horses.

År 1987 trädde en ny byggnadslag i kraft, Plan- och bygglagen(PBL). I och med den nya lagen minskade kommunens och byggnadsnämndens kontroll av projekteringshandlingar och besiktningar ute på arbetsplatsen. Efter lagändringen beror den slutgiltiga kvaliteten på en byggnad i större utsträckning på byggherrens och entreprenörernas egenkontroll. P.g.a. olika intressekonflikter inom kommunen, och att det kan förekomma starka kopplingar mellan byggherre och entreprenör, är det inte alltid självklart att kommunens tillsyn vid nybyggnation gällande till exempel egenskapskrav på energihushållning och värmeisolering utförs tillfredsställande.Med ovanstående i åtanke undersökte vi fyra flerbostadshus, två i Värnamo kommun samt två i Kristianstad.

The purpose of this master thesis is to investigate different types of measures for making buildings more energy efficient and to estimate their profitability. The calculations were performed with the building simulation program VIP+ and the evaluation of the profitability with the life cycle cost method. Furthermore, it was examined how losses in the distribution of secondary systems of district heating can be avoided. Options to replace district heating with a local district heating system based on bio-energy have been investigated. The possibilities of achieving more efficient thermal energy consumption and production for the chosen estate were also examined.The object of the study has been a residential estate with 133 detached houses in Uppsala, built in 1974.

At Forsmarks Kraftgrupp AB (FKA) forces on pipe systems due to transient flow are frequently calculated as a step to verify their structural integrity. In nuclear industries these forces are often calculated with a one dimensional thermal-hydraulic analysis-code called RELAP5. When calculations regarding more complex geometries are needed, the three dimensional code Fluent is often used. This code is highly time consuming and requires large computational power.This projects aim is to compare calculations of pressure, flow and forces carried out by RELAP5 and Fluent for an arbitrary pipe section during transient flow conditions. This has been accomplished by constructing a simple geometry for which a transient flow is simulated in both programs.

This paper is a literature study aiming to describe scientists newest theories andknowledge concerning the El Niño and Southern Oscillation. Firstly I have described the?normal? conditions with rising and sinking air in Hadley- and Walker-cells in theequatorial Pacific and from there moved on to explaining the reversed circulation patternsand higher sea surface temperatures (SST) leading to rising air and anomalousprecipitation in eastern Pacific constituting the El Niño phenomenon. My outermostinterest regarding El Niño has been the associated teleconnections, especially in nontropicalareas. I have described the El Niño effect on the Indian summer monsoon, ontropical cyclones and on storms and precipitation on higher latitudes.

Borrelios är den vanligaste vektorburna infektionssjukdomen i Europa och orsakas av bakteriekomplexet Borrelia burgdorferi sensu lato. Bakterien har en livscykel som involverar olika reservoarer och den överförs mellan dessa med hjälp av fästingar. Bakterien förekommer främst i fästingens mag-tarmkanal men kan också sprida sig systemiskt vilket kan påverka smittöverföringen. Fästingens utbredning i Sverige har ökat sedan början av 1990-talet, vilket tycks bero på ett varmare klimat i kombination med ökad tillgång till värddjur. Den här litteraturstudien syftar till att undersöka sambanden mellan ett varmare klimat och förekomsten av borrelios i Sverige. Klimatet har stor påverkan på fästingen och den har visat sig känslig för uttorkning och kräver en hög relativ luftfuktighet för att överleva.

To build a sustainable future should we first understand that; every aspect of our daily lives can affect the environment. It?s important that we take responsibility for understanding how we impact the environment and change our actions accordingly. The worlds total energy consumption equivalent to 80 million MWh / year. This corresponds to about 220 million MWh / day.Energy consumption is one of the main reasons for increased greenhouse gases when the reduction of this consumption has a great demand worldwide.In order to prevent the energy that consumed the buildings must be energy efficient but there is a conflict between radon ventilation and energy conservation in a building, given that ventilation can consume as much energy (currently 29-59% of energy-efficient houses use), especially in a cold climate as in Norway.

?A culture center should be visually welcoming as well as attract a diverse range of visitors with different backgrounds.? This was the client?s request for a new cultural center in Nairobi. The location is in the heart of Nairobi?s industrial area, near several existing buildings that are already in use by the culture organization known as Go Down. I have chosen to keep most of the existing buildings and to use my new building as a complement for the desired program.

The Swedish building and property management sector are responsible for about 30 % of the total energy use. In order to take environmental consideration, different environmental assessment tools and standards are used. Miljo?byggnad, Svanen, FEBY12 and PHI are some of these. There has been increased interest to certify buildings and therefore it is of interest to evaluate the assessment of the energy field to see if relevant energy aspects are assessed.

My thesis is an attempt to clarify the purpose and workings of art in relation to the artist, his/her fellows and society. Can art be considered as a uniting force? If so, where does its unifying quality lie? How does art connect with the individual, the community and society? My interpretation of the political climate regarding the arts has resulted in an exploration of the question: What role does art have in society today?The artistic ego as an altruism ? within the title of this thesis lies an absolute paradox ? a paradox that through this paper is tested, reviewed and demonstrated as a way of describing art and its workings. The thesis is problematized and studied from several angles: Through the inner artistic process, both reflective and empirical, and through philosophical studies..

The purpose of this thesis was to make an energy survey and quantify energy flows of individual unit operations associated with the biogas production in Uppsala Vatten och Avfall AB:s biogas plant, located at Kungsängens gård. Moreover, large consumers of energy would be identified and analyzed. The objective of this energy survey was to obtain a detailed understanding of the energy use in the biogas production.The energy survey was divided into two parts: electricity and heat. Each part was treated separately and with somewhat different approach. To estimate the electricity usage during the projcet the rated power of each selected unit operation was noted and multplied with thenmeasured time of usage.

The purpose of this thesis was to make an energy survey and quantify energy flows of individual unit operations associated with the biogas production in Uppsala Vatten och Avfall AB:s biogas plant, located at Kungsängens gård. Moreover, large consumers of energy would be identified and analyzed. The objective of this energy survey was to obtain a detailed understanding of the energy use in the biogas production. The energy survey was divided into two parts: electricity and heat. Each part was treated separately and with somewhat different approach. To estimate the electricity usage during the projcet the rated power of each selected unit operation was noted and multplied with the measured time of usage.

The aim of this work is to develop new conceptual designs for the fairings that are situated between the fin and the rear fuselage on the new version of the JAS 39 Gripen aircraft, called the Gripen E/F. The designs presented should show a profit in the form of lower weight. To achieve weight loss, the possibilities of using other construction materials other than those which are available at Saab today were studied. Therefore, a material survey was carried out in which the market for modern construction materials was studied to get an idea of today?s level of technology.

Rapporten innehåller inledningsvis en faktadel med allmän information kring temperatursprickor i betong. Här presenteras bl a uppkomsten av fenomenet, vilka typer av sprickor som förekommer och vad ett tvång är. Tanken är att ge läsaren tillräcklig kunskap för att kunna förstå sig på de övriga delarna i rapporten.Resultatet och det huvudsakliga arbetet redovisas i form av tabeller med tillhörande illustrationer där det går att utläsa vilken sprickrisk som förekommer vid flera specifika fall och vilken åtgärd som bör vidtas för att eliminera sprickrisken. Som konstruktör kan du med din egen indata, dvs. dimensioner och temperaturer, följa tabellen och finna resultatet för ditt specifika fall.