The purpose of this thesis is to clarify the grounds upon which an arbitration clause may be binding in the new relationship between the parties after a transfer of rights and/or obligations. The issue is not regulated by law but instead it has been left to the Supreme Court to regulate. In the Emja-case the Swedish Supreme Court left guidance on the issue. The Supreme Court stated that a third party purchaser of a right where the contract includes an arbitration clause shall be bound by the clause. The arbitration clause is only binding to the remaining part of the initial agreement if no special circumstances exist. The binding effect was justified by the reason that a situation where the purchaser but not the remaining part should be bound to the clause was not sought after and the principle through the 27 § of the Swedish debt instruments act..

A system for sampling of alcohol and aldehyde from diluted exhaust gases from vehicles powered by ethanol has been developed and tested. The major part of the work has been research of earlier work in the field and the construction of the sampling system.The part of the system constructed for the measurement of alcohol has been shown to work, however, more test should be performed. The part of the system constructed for the measurement of aldehyde was tested parallel to a commercially available system, based on the same principle of measurement, and has been shown to work well.Determination of the concentration of gaseous ethanol using a FID has shown the since earlier known fact that a FID is not able to measure a correct concentration of ethanol. Furthermore it has been shown that high concentrations of gaseous ethanol can not be kept in a bag more than a few minutes without a substantial decrease of the measured concentration..

This degree project has been carried out in cooperation with Enertech AB in Ljungby and is pilot study to automating all current manual soldering. The soldering process accounts for a large part of the processing cost in the production of a heat pump. The process is also a quality risk and has a major impact on the lifetime of the final product.The Main task of this project has been to evaluate automation of the soldering process, to develop automation solutions and a principle layout, to draw the design changes required for the automation and to calculate the supposed solution.This pilot study has resulted in a suggested automation solution using laser as a heat source for soldering. Calculations of the solution show that a automating a laser soldering cell is very profitable..

This essay deals with the principle of surprise warfare and its development as well as the adaptation of military action that had to be made to surprise the opponent in the modern era.The concept of surprise is divided into its components in order to clarify what is required to implement a surprising maneuver, to understand the complex concept and form a theoretical framework for gathering facts in the case study.Development and adaption are demonstrated by a comparative case study where Pearl Harbor illustrates an example of historical surprise and Operation Desert Storm illustrates a modern surprise. The product will then be analyzed in order to detect the development and how military conduct is forced to adapt in order to carry out a surprising maneuver. The results shows that the military action of performing a surprise attack has had a major development and is now carried out in a different stage of the attack..

In this essay a model of a potential illegal hunter?s decision-making is created and presented in order to provide an overview of important parts of the complexities associated with the current Swedish predator policy. A comparison is made between a livestock owner?s economic incentives, and the expected costs faced by the potentially caught lawbreaker. In accordance with economic theory the benefits and costs of illegal hunting are compared and thus the optimal choice is determined where marginal costs and benefits are equal.

This degree project has been carried out in cooperation with Enertech AB in Ljungby and is pilot study to automating all current manual soldering. The soldering process accounts for a large part of the processing cost in the production of a heat pump. The process is also a quality risk and has a major impact on the lifetime of the final product.The Main task of this project has been to evaluate automation of the soldering process, to develop automation solutions and a principle layout, to draw the design changes required for the automation and to calculate the supposed solution.This pilot study has resulted in a suggested automation solution using laser as a heat source for soldering. Calculations of the solution show that a automating a laser soldering cell is very profitable..

This essay deals with the principle of surprise warfare and its development as well as the adaptation of military action that had to be made to surprise the opponent in the modern era.The concept of surprise is divided into its components in order to clarify what is required to implement a surprising maneuver, to understand the complex concept and form a theoretical framework for gathering facts in the case study.Development and adaption are demonstrated by a comparative case study where Pearl Harbor illustrates an example of historical surprise and Operation Desert Storm illustrates a modern surprise. The product will then be analyzed in order to detect the development and how military conduct is forced to adapt in order to carry out a surprising maneuver. The results shows that the military action of performing a surprise attack has had a major development and is now carried out in a different stage of the attack..

To be allowed to sell Z-suspended vehicles with dipped beam Xenon or LED lighting, Scania have to develop automatic headlight level control. This master?s thesis aims to be the foundation to that development.The thesis consists of several parts; a market analysis of how competitors to Scania and the general vehicle industry solve this problem; several available principles for detecting the amount of control needed; the construction of a test station for sensors, a control unit and components connected controlled by the control unit; a further theoretical and practical development of one principle ? one rotational sensor connected between the chassis and the back drive axis; a state flow model programmed in Simulink that produces the control signal for the headlight leveling from the sensor input.Lastly the thesis gives some recommendations to the further development and implementation of automatic headlight level control on Scania vehicles..

Recent statistic shows that about 28% of adolescents living in Stockholm drink alcohol at such a high level that their consumption counts as risky drinking. The correct term to use in this matter would be binge drinking adolescents.  In the more wealthy areas of Stockholm this group of binge drinking adolescents counts for as much as a third of the population. In contrast, the adolescents living in exposed areas do not drink nearly as much. Binge drinking adolescents in these areas only counts for 15%, nearly half as much as in the wealthy areas.In light of this the intentions of this study is to investigate which explanatory factors that can clarify the range-rated differences in binge drinking between adolescents in Stockholm.

This thesis investigates if privatization of the Swedish healthcare system influences our view on the meaning of equality. This system is based on the principle that all people are equals and that healthcare should be provided on the basis of need. I apply critical ideology analysis to investigate how our view of equality might change because of the evolvement of society. A critical view may be explained as an interest in exploring things that seem obvious to many. Important questions to answer are why equality is regarded as such a natural concept in the society and how healthcare is actually provided.

The project has been oriented for development of fixtures to ateljé Lyktan to provide a more efficiency line. In the year 2012 the company invested in a new coating booth, which leads to opportunities to upgrading the fixtures and also new design. The request is to minimize the area for storage of fixtures, and therefore should fixtures be designed to apply as many articles as possible The priority of products that fixtures have development to has been products that are most frequently coated and new products that don?t have any fixtures. The product families that the project has been having focus on is TIME and FOVEA with RONDO.

This degree project was conducted in collaboration with Gremo AB located in Ätran.The aim of the project was to develop a solution to secure quality and to help assemblingthe locknut holding the vertical hinge on the harvesters and foresters from Gremo.At this time the nut is assembled manually by the aid of an overhead crane. The nut istightened differently from time to time, and there was no specified torque to which it istightened. Another present problem was the locking washer which sometimes getsdamaged during assembly, when this happens the procedure has to be started over fromthe beginning. The current assembly procedure is very time consuming and lengthy forthe employees.Our task was to design a machine that could tighten the nut to a specified torque with amargin of error of ± 3%. The assembly procedure will be held simple and the timerequired at a minimum.The project started by developing several principle solutions, the one solution that bestmatched our specifications were developed to a primary solution.Today we have started manufacturing and assembling our prototype.

The aim of this essay was to examine how the decision-making in LVU cases are motivated in the judicial decisions. How has the principle of whats in the best interest of the child been noticeable in these judicial decisions and how are the child's needs and the consequences for the child of the drug abuse been described? When the parents have been judged to have given a non acceptable consent, how have they been described and how has the parents described the situation?Our research is of a qualitative nature, a document analysis of judicial decisions in LVU cases. We analyzed eight court cases containing decisions from County Court, Fiscal Court of Appeal and The Supreme Administrative Court.Our results showed that parents were described in the judicial argumentation as negative stereotypes and a picture of unreliability were created. What was best for the child were not expressed in words but woven into the children's needs and in most cases the consequences of the abuse of drugs were not made clear..

What drove me to write this paper is the will to  examine if there is a philosophically and scientifically viable  alternative foundation for an objective morality other than what we like to refer to as "God". The  American philosopher and neuroscientist Sam Harris presents in his book The Moral Landscape a thesis for an objective morality based on science in which he states that  science can determine human values. The purpose of this paper is to perform a theoretical trial of The Moral Landscape, examining Harris' thesis and it's relations to the philosophical obstacles that stands in its way, these being mainly the famous philosophical principle "Hume's Law" and G.E. Moore's "Naturalistic Fallacy and Open Question Argument" and thus will serve as my main theoretical foundation. The results of my study was not conclusive since Harris in fact doesn't succeed in bridging the gap between facts and values on a scientific ground.

To be allowed to sell Z-suspended vehicles with dipped beam Xenon or LED lighting, Scania have to develop automatic headlight level control. This master?s thesis aims to be the foundation to that development.The thesis consists of several parts; a market analysis of how competitors to Scania and the general vehicle industry solve this problem; several available principles for detecting the amount of control needed; the construction of a test station for sensors, a control unit and components connected controlled by the control unit; a further theoretical and practical development of one principle ? one rotational sensor connected between the chassis and the back drive axis; a state flow model programmed in Simulink that produces the control signal for the headlight leveling from the sensor input.Lastly the thesis gives some recommendations to the further development and implementation of automatic headlight level control on Scania vehicles..