Starting point to this Paper is the idea and wish to adapt the society and its different activities to a recycle society. A building area in Göteborg is planned and investigated for such adaptation. In the district named Skogaberg, about 130 households totally are planned from what 20 are blocks of flats. The idea with this project is to constitute an alternative sewage system, a Blackwater system, were the fractions of most nutrients and least pollution are separated, taken care of and utilised. The aim is to get a market and use the nutrients of the organic waste from the household in agriculture use.

Population growth leads to an increased need for new buildings, both residential and commercial. The regulations of structural design also changes with time. From a sustainable community perspective it may be profitable if existing buildings, that no longer performs their original function, are reconditioned. Knowledge and understanding of the surroundings of the residence must be available. Regulations regarding accessibility to all has increased.

The goals of this Bachelors? Thesis were to establish the production loss through the VTIS1 Pasteur at Arla Foods Linköping dairy and then suggest simple but effective solutions to minimize the losses for each production run. If the timeframe allowed it, some of the solutions would be implemented and tested in full production to determine their impact on economic and environmental savings.The very first step of this project was to establish the statistics over what losses there is in the production pipeline through VTIS1, from milk and powders in mixer tanks to finished and packed products in cold storage. Then, when knowing how much product was actually lost and where, those bottlenecks could be pinpointed and examined more closely. At this stage the focus was switched, from the otherwise complicated and broad manufacturing process, to the VTIS1-aggregate, since early data indicated there were quite substantial losses there.In conjunction with this project Arla Foods purchased an absorption photometer-measuring device (OPTEK AS16) that could be inserted straight into the product stream out of VTIS1, allowing real time measurements of its optical density.

In recent years, Lean has been implemented in a variety of companies with focus areas that differ from the conditions that characterizes manufacturing. This transfer has contributed to fairly superficial results because companies almost exclusively focus on Toyotas methodology and not on the goal of Lean. The effort of transforming Lean from manufacturing to any organization requires a definition on a general level and a view of Lean as a system. One of the core principles of Lean and the foundation of continuous improvements is standardized work. In product development there is a negative view on standardized work, where the engineers state that the principle is not applicable for knowledge processes that include non-repetitive and creative work.In the framework of this master thesis literature has been studied to find support that standardized work is applicable for product development and areas that include knowledge processes.

Background ? The last 20 years healthcare has been facing increased demands on efficiency and increased customer satisfaction. This despite reduced resources and increasing demand. These demands are presents in all departments within healthcare organisations, including medical laboratories that currently receive an ever-increasing number of remittances. Laboratory flows are quickly becoming overloaded with samples and related materials.

In recent years, increasing emphasis has been placed on streamlining the supply chain. Keeping inventory and warehouses is considered to be a waste of resources. It is however difficult to completely eliminate the need for inventory and warehouses in a supply chain. The purpose of warehousing is to provide a service for the customer. By keeping what the customer demands in inventory it is possible to make a quick delivery when a need arises.

GE Healthcare wants to investigate whether additive manufacturing would be an alternative method in their workshops in the Umea? plant. Additive manufacturing is called 3D printing in everyday language and manufactures details by building them up layer by layer in an automated machine. The purpose of this work is therefore to investigate how mature additive manufacturing methods are and how they could be used at GE.The work has been divided into three parts. The first section investigates how additive manufacturing would work in the production workshop at GE.

Four different kinds of filter-materials with reactive surfaces have been studied concerning their capacity to absorb heavy metals in leachate from a municipal waste deposit. The heavy metals studied were: lead, cadmium, copper, mercury, chromium, nickel and zinc. The leachate contains high levels of dissolved organic carbon (DOC) and has a high pH-value along with a high buffer capacity. These characteristics of the leachate make it difficult to remove pollutants and require efficient filters. The filters that were examined in the report are blast-furnace slag with CaO, sand covered with iron oxides, olivine and nepheline.

AbstractClimate and environmental issues are of paramount importance. Researchers agreethat we must all contribute to a reduction of gases that contribute to climatechange. Energy consumption must decrease within all sectors and the promotionof renewable sources of energy must be introduced.Each sector should aspire to decrease its energy consumption. Energyconsumption is strongly linked to waste gases that contribute to climate change.Passive houses are a part of the construction industry's methods to attain energyconservation.Passive houses are derived from low energy houses and super insulated houses. Apassive house is intended to obtain heat from the inhabitants and through theiractivities.

The nitrogen cycle in freshwater bodies is complex and consists of many separate processes affected by a number of important factors for example oxygen concentration in the water, temperature and circulation. Knowledge of the different components of the nitrogen cycle exists; however, a complete and comprehensive picture is difficult conceptually as well as theoretically. The available literature illustrates that the research on nitrogen and the related freshwater processes is still associated with high uncertainty of how much of the supplied nitrogen from the catchment is transported with the water versus and how much is lost due to denitrification, sedimentation or uptake by plants. This report is an interdisciplinary survey of Nitrogen discharge permitting. The research focuses in particular on the decision-making process, the levels of scientific standard and the administrative framework.Application for Nitrogen discharge permits are decided by the Environmental Court with council from their own experts as well as relevant government authorities and organisations.

The demand for animal products has increased in the last decades, especially for poultry and pork. Pork production has increased drastically globally, and also in Uganda. Thirty-one percent of Uganda´s population lives in poverty. Pig production is believed to play a crucial role in poverty alleviation, because of the ability to convert low quality feed into high quality protein together with high reproductive potential. African swine fever (ASF) is a lethal disease of domestic pigs often characterized by haemorrhagic fever and with mortality rates up to 100%. The disease is endemic in most sub-Saharan countries and since 2007 in the Russian Federation and Caucasus area.

The aim of this study is to investigate which communication strategies and channels the mu- nicipal company Falu Energi & Vatten should use in order to become more efficient in com- municating with citizens between 18 to 29 years old. The company is owned by the munici- pality of Falun and manages community services in electricity, district heating, fresh water, sewerage, metropolitan area network and waste disposal. The following theories have been used in the study: convergence culture, digital natives, information overload, communication strategies and uses & gratifications theory. The methods used in the study are 4 focus group interviews and one informant interview. The members of the focus groups where within the age range 18-29 years and lived in the city of Falun.

The purpose of this study is to incrementally, through a combination of various methods, examine the assumptions about the working economic outcomes that can be made based on planned ergonomic intervention in a department at Pfizer Health AB in Strängnäs. The study contributes to knowledge about how assumptions on OSH financial results can be made, based on planned ergonomic interventions. These assumptions were based on biomechanical calculations made on the basis of ergonomics measurements with inclinometer. The study is important because previous research has shown that poor work environment have a bad impact on the economy of a company in different ways. It can for example be negative impact on the company's productivity and quality of the units produced or the services provided.

GE Healthcare wants to investigate whether additive manufacturing would be an alternative method in their workshops in the Umea? plant. Additive manufacturing is called 3D printing in everyday language and manufactures details by building them up layer by layer in an automated machine. The purpose of this work is therefore to investigate how mature additive manufacturing methods are and how they could be used at GE.The work has been divided into three parts. The first section investigates how additive manufacturing would work in the production workshop at GE.

To create a profitable and competitive business an important factor today is a well-functioning logistics. Through effective internal material flows effective logistics can be achieved. Unnecessary handling and movement of materials is a waste which affects the internal material flow. These wastes should be identified and eliminated as much as possible to improve the internal materials handling and through that achieve a more efficient business. At Fagerhults Belysning AB, where professional lighting systems are developed, manufactured and marketed, a new inventory has been built and changes in the assembly has been made during the past year.