This thesis paper presents experiences and views on collaborative writing from interviews with university students. Analysis of these interviews, focusing on problems with coordination and technological tools,  shows that problems to some extent can be avoided with knowledge of the tools used and knowledge of coordination..

The effects of dexmedetomidine and butorphanol sedation on skin reactivity during intradermal testing in healthy dogs were evaluated. The effects of dexmedetomidine and butorphanol were compared to medetomidine, a sedative agent having scientific proof of not interfering with skin test reactivity, in a randomised, double blind, cross over study performed on 8 adult dogs. The dogs were sedated with medetomidine (Domitor vet.®, 0,01 ml kg-1) intravenously, or dexmedetomidine and butorphanol intramuscularly (Dexdomitor vet.®, 0,01 ml kg-1; Dolorex vet., 0,01 ml kg-1) after which they received intradermal injections of positive control solutions (histamine 0,1 mg ml-1, 0,05 mg ml-1, 0,025 mg ml-1), a negative control solution (0,9 % NaCl) and allergen extract (Dermatophagoides farinae, Cladosporium and Artemisia vulgaris). After a wash out period the trial was repeated with a reversed sedation protocol.Skin reactivity (wheal size, induration and erythema) and quality of sedation (immobilization, response to stimuli and injections as well as over all working conditions) were evaluated. The combination of dexmedetomidine and butorphanol provided reliable, good sedation and analgesia without adverse effects.

During the past few years there has been an observed decrease in physical fitness within different patient groups. As a part of the rehabilitating physiotherapy treatment it is important to acknowledge the physical condition of the patient. Physical fitness testing might be difficult due to physical limitations within different patient groups. A broad range of exercise tests is therefore of importance in clinical practice. The aim of this overview was to describe exercise tests used in rehabilitation contexts, and to define areas of use and restrictions.

There are several ways of conducting software testing where some may include users and others may include personnel whose work task is to execute test on systems. Although most developers and project managers understand the point of testing the system, it is not always being done and the most common reason is that there is no time for it. However, this is a false assumption as it may instead cause some bugs in the system that would not have been there in the first place if tests had been there to prevent bugs in the code.My purpose for this thesis was to find suggestions for changes in the development process in an ongoing project used by Acino and Svenska Försäkringsfabriken in order to increase the quality of the system used. In this thesis, I have approached the purpose by pursuing a case study of the two companies through observation and interviews. By doing this I acquired the relevant information to make suggestions for change.

The project, Flexible Snowboard System, has been carried out by the project group independently and is a module developed for snowboarders, ski rentals and ski schools. The problems of today?s solutions are that they cause the user an inconvenient standing position when riding the ski lift or skating the transportation slope, also mounting, adjustments and disassembling of the bindings are time consuming and brings undesired wear to the screws and screw holes. In addition any adjustments require that the user steps out of the bindings and have tools at hand. Flexible Snowboard System is a universal module which means that it can be assembled with all of today?s snowboards and bindings.

The project, Glowtest Fixture, has been carried out to and in collaboration with MSA SordinLtd. MSA Sordin Ltd produces and sells ear protector and is at present a supplier on theworld market. Glowtest Fixture is a product for glow testing off detailed components in oneear protector. MSA Sordin Ltd sends today away your products for testing what is anexpensive aspect in their development. The project's aim is to take forward a test equipmentthat copes with those high nonplussed requirements and wishes that are required for anapproved physical execution.Glowtest Fixture is a physical equipment that comes used stem glow physical off all detailedcomponents in one ear protector.

The competitive nature of the automotive industry has always implied a necessity to improve product development concerning time-to-market, cost and product quality. As capacity of computer-aided engineering (CAE) tools has evolved, so has the strive for simulation-driven design. Virtual durability testing using full vehicle models is one of many challenges posed in front of vehicle manufacturers when computer simulations are given a key role in product development.This thesis has been initiated as a preliminary step towards implementing dynamic virtual durability testing in the development of buses and coaches at Scania. The objective has been to assess the predictability of a full vehicle coach model and to what level of precision structural loads can be predicted. Previously performed proving ground testing of a Scania Touring coach has been the basis for the modelling and simulations in this thesis.A virtual model of the Scania Touring coach has been created in multi-body simulation software package MSC.Adams.

Modern semiconductor design methods makes it possible to design increasingly complex system-on-a-chips (SOCs). Testing such SOCs becomes highly expensive due to the rapidly increasing test data volumes with longer test times as a result. Several approaches exist to compress the test stimuli and where hardware is added for decompression. This master?s thesis presents a test data compression method based on a modified facsimile code.

The focus of this thesis is primarily in electronic construction and describes the design process for a microcontroller circuit board from concept development to prototyping. The client develops test fixtures for automated testing of products within the electronics industry and needs a new controller circuit for the test fixtures that can handle controls and basic testing. An investigation into the needs of such a system is conducted and a prototype printed circuit board assembly is manufactured.The prototype is developed with focus on protection against electrostatic discharges and overvoltage. Among the functions that are included are voltage measurements, communication interfaces and control of input and output currents. Firmware for the prototype is developed and configured to communicate with a PC through USB interface for control and collecting of measurements..

This essay examines pull-out strength of threaded rods fixed into glulam timber. The technology is intended to be used in hidden joints between glulam components. The work began with a study of literature focusing on current research within the topic, mainly to create a base of knowledge before the testing was initiated. Studies of scientific articles reveals a lack of research within this area, which makes it difficult to develop standards and calculation models for these joints. The drill holes in the tests have a diameter of 7 mm.

The purpose of this thesis was to design an electrical system for use in a ballistic test at the Swedish National laboratory of forensic science (SKL). The detector unit would use four main parts: coilsystem, transmitter, reciever and indicator. The coilsystem would be based on a balanced system using three coils. One that creates a magneticfield and the other two will sense the differences when a metallobject is in the coilsystem. This report starts out by investigating possible solutions for this specific task followed by a description of the physics that the metaldetector use.

The project involves implementing a finished dispersion model into ArcGIS. The goal of the tool is to show how dangerous and toxic substances will travel in the ground after long periods. The goal of the project is to understand GIS in general, what it is used for and gain an insight into how developing tools for ArcGIS is, what challenges might exists. Understanding the type of data that can be stored and accessed in ArcGIS a long with the tools and functionality offered by the system when using Python as the main language for development. A prototype of the tool is created..

AbstractA continuous improvement of products and production is an important goal for a modern industrial company. A small engineering group located in Sweden came in touch with the authors of this report during the spring semester of 2014. The aim of this report is, as part of the group´s ambition of improvement, to analyse ways in which the quality of component casted parts can be verified. Non-destructive testing (NDT), and methods to use it for quality control, is the main focus of this report. However, fields such as material standards, component casting and quality engineering are analysed as well.

This report describes the construction of a climate-cabinet for testing of HV-cards (High Voltage) produced at VG Scienta. The main part of the report describes all the different components of the cabinet. The most important parts are a PID regulator from Eurotherm model 2408, a solid state contactor (SSC), a thermocouple, a finned resistor from DBK and different fans. The report even includes the connection between components by cable wiring, isolation, grounding, fuses and shaping of metal goods.As the cabinet also communicates with a computer, the report includes the solution of the data communication using the software iTools from Eurotherm. The communication part includes information about a converter that converts EIA422 to USB.The cabinet was produced at a company, called VG Scienta, in Uppsala during the spring 2010.

The aim of the study was to examine both 1) how aware teachers in a specific area are about ICT tools in teaching ; and 2) how likely teachers are to use ICT tools to reverse the trend of unmotivated students and low achievement scores . I will look for answers through the following questions:How extensive is the knowledge of the teachers on digital and social media in education? How have teachers in the past year used various social media in their teaching? In what grade does ICT-supported teaching lead to higher motivation, participation and achievement? Is there a difference between the sexes, different stages (1-3, 4-6, 7-9) and number of years in the profession in knowledge of and openness to the use of ICT in education?The method used is a questionnaire in which a number of respondents have answered a number of questions about ICT tools in teaching. Validity of the study can be said to be high when the survey has measured what it intended to measure, however, I need to be careful in draw full account of the result as the response rate is low with only 39%. In summary, the results show that there is low awareness among respondents about the methods and the digital and social tools I lift in the survey.Mainly the respondents use some of the methods and the digital and social tools in preparation for the lesson.