SAMMANFATTNING Uppskattningsvis transporteras 171 miljoner grisar inom EU varje år, varav ca 3,5 miljoner i Sverige. Grisarna kommer, under hela förloppet från förflyttningen från box i stallet till bedövningen i slakteriet, att utsättas för stressande moment. Orsakerna är bland annat omgrupperingar, nya miljöer, vibrationer i bilen samt, speciellt under sommaren, värmestress. Temperaturen i djurtransportbilen är en nyckelfaktor som dessutom kan förstärka effekten av andra stressorer. Lastning i höga temperaturer ökar risken för värmestress. Värmestress innebär att djuren får allt svårare att avge sin värme. Även den relativa luftfuktigheten har betydelse, framförallt vid temperaturer över 30°C. Det är ventilationen i transportbilen som ska transportera bort värme och fukt från bilen.

Envirotainer builds containers that are specialized in transporting of temperaturesensitive products these containers are customized for airplanes. The containers arethen leased to other companies, most often to pharmaceutical companies.Envirotainer are based in Lagga, Knivsta. It is also here where the production of thecontainers is held. The container RAP T2 was designed in the early 80ies. The RAPT2 contains a fleet of about 1220 containers spread all over the world.

When constructing a building, a number of aspects must be harmonized in order for it to fulfill requirements ? a building must fulfill requirements such a load-bearing, conservation of energy and a good indoor environment by means of, among other things, moisture proofing .Moisture problems in buildings can affect health negatively. As we are increasingly staying in indoors, demands on a good indoor environment are higher.This work starts with examining moisture problems in slab-on-ground solutions, and then links the various scenarios to moisture problems in a concrete slab of a real building. The building with moisture problems is located in Årby by in Borlänge and moisture damage was found in the slab at an apartment adjoining wall.By reviewing literature written within the field of moisture problem, making hand calculations and modeling in the program Comsol Multiphysics, judgments are made to find explanations as to why the rise of moisture occurred in the building in Årby by.Generally, the following guidelines may be used to reduce the risk of moisture problems in slab-on-ground constructions:Drying of construction moisture before laying the floor material.Using draining layer beneath the slab, to prevent capillary suction.Using insulation under the slab, partly for comfort and to establish the temperature difference between the ground and the concrete slab.Avoid direct contact between the wood and concrete, due to degradation and fouling smells that normally occurs.If necessary, use additional vapor barrier.In addition to the above, there are various methods for moisture-proof and moisture-monitoring by design or by the method ByggaF suited for the entire construction process various events..

Since their invention in 1999, CubeSats have become a widespread standard for small picosatellite missions. CubeSats allow for quick development of satellite payloads and launch in space without the high costs of a normal satellite. Emphasis during the CubeSat design process is placed on use of commercialoff- the-shelf (COTS) components and reuse of previously-designed units.This report describes the interfacing of a scientific magnetometer, the Small Magnetometer in Low-Mass Experiment (SMILE) to such a CubeSat mission, the Space Weather using Ion spectrometers and Magnetometers (SWIM). Design of a complete platform for use in multiple such missions is presented here.Modularity is one of the key aspects followed in the course of the work. A new board containing the analog pick-up and compensation circuitry for SMILE has been designed to fit inside a CubeSat frame.

This Master of Science Thesis was a complement project to the PIEp study MENTOL, carried out at a Swedish midsize medical device company.. PIEp nationally works for a long-term increase of the innovation capability of people and organizations. The purpose of this study was to find measuring parameters of innovation that fit medium-sized technological companies and organizations, Another purpose was to evaluate an innovation investment at the company, consisting of external consultant?s education of key personnel in innovation, and a two day innovation seminar with all personnel at the company participating. The methods used during this Master of Science Thesis were: feasibility and literature studies about innovation and innovation measurements, quantitative and qualitative interviews, surveys and workshops.For an accurate measure of innovation it is crucial to a have full understanding of what innovation is, and clarity of the purpose of the measurement itself.

Protein is an important component in various milk products and has a crucial role in the final quality. Excluding non-protein nitrogen, bovine milk contains about 3.3% protein whereas about 80% of this fraction consists of casein. There are four major members in the casein family: ?s1-casein, ?s2- casein, ?-casein and ?-casein. Proteolytic enzymes are the cause of degradation of the economically important milk proteins.

The purpose of this report is to investigate the possibilities with drain water heat recovery (DWHR) in residential buildings. Information and relevant theory has been collected and summarized in this report. Calculations have been done for given scenarios to evaluate profits. DWHR heat exchangers use simple technology and have long life-time. The heat exchanger is connected to outgoing drainage pipe and incoming cold-water supply so countercurrent flow is accomplished.

This study has focused on obesity prevention efforts in schools in the United States of America. The study was conducted in two states, Oklahoma and New Hampshire. In New Hampshire, the study was focused on more minor efforts which were the "CSHP", HEAL, Early Sprout, FIT, AFHY, 5210, and Kids CATCH Club. In Oklahoma, the focus on the study was on the program It's All About Kids.Method: Unstructured interviews and observation, analysis from an national policy document. A total of seventeen interviews conducted, seven of them in New Hampshire and ten in Oklahoma.

The surface finishing technique called black oxidation is currently being used on thetool holders made of low alloyed tool steel produced by Sandvik Coromant. Blackoxidation isn?t considered a sufficient technique because it doesn?t make the toolholders look like the quality products that they actually are. The reasoning behind thisis that the tool holders can show signs of corrosion after prolonged storing times orin countries with high humidity and temperature. The corrosion doesn?t decrease thetool holders performance, but the customers might believe otherwise.

AbstractIn urban societies people spend more and more time indoors, which put great demands on the indoor environment. If the ventilation is to manage the removal of unwanted substances in the indoor air, a good mixing of the air is required. The question arises that, whether the buoyancy forces will counteract a good mixing of the indoor air or not?This report aims to clear up the difficulties whether you need to consider the buoyancy forces or not, when adjusting a ventilation unit. For studying the indoor mixing of the air a two dimensional model is constructed in COMSOL Multiphysics.

This project has as main goal to study the influence of the coating thickness, deposited by arc-PVD- technology, on the wear resistance of coated cemented carbide inserts in three different turning operations. An additional effort has also been made to develop a new test method for evaluating flank wear resistance. Three different coating types (Coating A, Coating B and Coating C) have been studied in three distinctive thicknesses (2, 4 and 6 µm) for each type. For two of the coating types (Coating A and B) special studies has been done with the thickest coating, creating two additional coating versions of the thickest coating, by changing various deposition parameters, with the aim to enhance the cohesive properties of the coating and lower the residual stresses at the cutting edge. The results show increased crater wear resistance with increased coating thickness for all coating types, but the amount of increase changes with coating type (Coating A>B>C).

The report examines the factors which may be a contributing cause to the problems that are present when ferritic stainless steel are eddy current tested in a warm condition. The work is carried out at Fagersta Stainless AB in Fagersta which manufactures stainless steel wire. In the rolling mill there is an eddy current equipment for detection of surface defects on the wire. The ferritic stainless steels cause a noise when testing and this noise complicates the detection of defects.Because of this, a study was made of how the noise related to factors such as steel grade, temperature, size and velocity. By observing the signal and with the possibilities to change the equipment settings the capability to let a signal filter reduce the noise level were evaluated.

The travel agencies exist on a market that is distinguished by increasing competition. A majority of the travel agencies offer different services that all satisfie the same customer need. However,one major difference in the market aspect is the service quality, this making it an important mean of competition. There are several acknowledged methods of measurement when it comes to service quality and it is important to use an instrument that takes into consideration the fact that charter tours is a complex merger of several services. The purpose of this essay is to establish if the SERVQUAL method is a suitable instrument for measuring service quality in the travelindustry.

Oavsiktlig lindrig hypotermi förekommer hos upp till 60 % av de patienter som genomgår en operation. Hjärnans förmåga att reglera kroppstemperaturen under ett operativt ingrepp påverkas av läkemedel som ges under anestesi. De åtgärder som vidtas innan och under operationen för att minska temperatursänkning är ofta otillräckliga och behöver förbättras. Idag finns få rutiner för hur oavsiktlig lindrig hypotermi skall undvikas för att minska det lidande som kan uppstå då patienten oavsiktligt utsätts för avkylning perioperativt. Syftet med studien var att påvisa de risker och effekter som uppstår i samband med oavsiktlig lindrig hypotermi perioperativt, samt att belysa framkomna skyddande faktorer.

Gunsta is situated about 10 km east of Uppsala. Today there are plans to establish 1000 new households in Gunsta before year 2030. The required energy for heating houses and water would be distributed via a district heating system, which also includes 200 existing residences. The annual required energy, according to this study, would be 16.2 GWh with a maximal peak effect of 6.9 MW. To meet this need, the study suggests a system with heat pumps to upgrade the 31?C water from a 1.8 kilometre deep borehole.