Journalists´ role in society has traditionally been of representative nature with a task to distribute news and scrutinize those in power. But technological changes have created a new publishing world outside the traditional media institutions. In today?s redactional society anyone can become a publisher in a blog or through other channels on online. This process can be seen as contributing to increased democratization giving everyone the opportunity to publish.

A wastewater treatment plant has the task to refine the wastewater from substances that should not be released into the environment. The decomposition process can, in a simple way, be described as follows: micro-organisms breathe oxygen and eat unwanted substances. The environment in which the micro-organism lives is known as sludge and the correct amount of oxygen available in the sludge is important for the decomposition to be effective. The oxygenation of the sludge alone stands for about 30% of the plant?s energy consumption.

This report is a study in voltagelevel in connection with regeneration of brake energy from the tramtype M31 in Gothenburg.In the act of braking, the tram M31 uses electrical braking where the electrical motors generates energy and if possible send it back to the overheadline, where other trams in the nearby can use this regenerated energy for its own driving force. In cases where no other energyconsumers are located in the same section, there is a resistance witch task is to convert this energy into heat. The regulation of this resistance appears to cause an increase in the voltagelevel into far too high levels.Investigations of the trams regulationequipment and its construction have been done. Further have measurements on the overheadline been performed in order to map the voltagevariations during a longer period of time.The result have been showing that the voltagelevel during regeneration often is as high as 880V-920V, more extreme values have not been observed in a large scale. The values are especially high compared to the nominal voltagelevel.

Environmental enrichment is of high importance for zoos. Borås zoo asked SLU (Swedish University of Agricultural Sciences) for a student to perform a bachelor thesis for them. The task was to develop and evaluate environmental enrichment for their Humboldt penguins. A structure was made, consisting of a sinking skeleton with a floating bridge attached to it. It was presented in an area of the pool that the keepers had experienced that the penguins did not use to any extent.

This essay focuses on the term usability while conducting a user centred system design. Usabilitymeans to what extent a user can use a product to achieve effectiveness, efficiency and satisfaction.Development using a user centered system design means that knowledge about the end-users andit?s opinions becomes a crucial part of the development process. The question of this essay is if usinguser centred system design will lead to good usability.We used methods from a user centered system design point of view while developing an applicationfor a Swedish bookstore company called Bokia AB. This included user and task analysis following by aclose relationship between the developers and end-users by using sketches and showing themprototypes of the system while collecting feedback.After concluding our case study we determined that using methods from user centered systemdesign could be used as a great tool to further improve the usability and to improve an applicationssuccess chances..

This study was carried out in Ronneby municipality during May 2006. I chose to compare three senior schools with regards to the implementation of objective orientated directives based on the teachers understanding of the task, motivation, resources allocated and their significance for the disparity between boys? and girls? grades.I carried out nine in-depth interviews: three at each senior school. From the interviews it emerged that teachers perceive objectives differently from parents and students. Teachers claim that they understand the directives but say that they lack the resources.

This report treats a Master Thesis performed at Scania CV AB. The task was to create a computer model of a hydraulic actuator system in the software AVL Hydsim. The system consists of two spring-loaded masses with surrounding hydraulic components. The purpose of the model is to study phenomenon and problems in the system, as well as to be a support in the development of the system. It is not supposed to be used to study absolute values in its current form.

abstract buzz marketing, the phenomena Have you ever thought about why the small French pastries called macarons suddenly became so extremely popular? Soon they were seen everywhere in the media, on every celebrity party and shortly after of course on every Swedish person?s cake dish. Could it be that a trendy it-girl happened to mention these lovely creations in her blog?What (or who) is it really that decides and controls what is popular and what is going to sell? If one individual can influence a whole group of followers it is definitely something marketers should take advantage of. One cannot any longer rely on traditional advertising, one needs to be more creative and rethink the possibilities to get through the media noise.

Manliga sjuksköterskor är en minoritet såväl som en anomali. En allmänt utbredd föreställning existerar om behovet av ett större antal män inom vården. Vårt syfte är att studera konstruktion av maskuliniteter hos sjuksköterskor i vården. Vi vill även söka efter vilka hinder, strategier och möjligheter som finns i skärningspunkten mellan maskuliniteter och vård. Denna studie är en litteraturstudie baserad på 16 artiklar vilka söktes fram genom PubMed och CINAHL.

This report is a study in voltagelevel in connection with regeneration of brake energy from the tramtype M31 in Gothenburg.In the act of braking, the tram M31 uses electrical braking where the electrical motors generates energy and if possible send it back to the overheadline, where other trams in the nearby can use this regenerated energy for its own driving force. In cases where no other energyconsumers are located in the same section, there is a resistance witch task is to convert this energy into heat. The regulation of this resistance appears to cause an increase in the voltagelevel into far too high levels.Investigations of the trams regulationequipment and its construction have been done. Further have measurements on the overheadline been performed in order to map the voltagevariations during a longer period of time.The result have been showing that the voltagelevel during regeneration often is as high as 880V-920V, more extreme values have not been observed in a large scale. The values are especially high compared to the nominal voltagelevel.

This report is a study in voltagelevel in connection with regeneration of brake energy from the tramtype M31 in Gothenburg.In the act of braking, the tram M31 uses electrical braking where the electrical motors generates energy and if possible send it back to the overheadline, where other trams in the nearby can use this regenerated energy for its own driving force. In cases where no other energyconsumers are located in the same section, there is a resistance witch task is to convert this energy into heat. The regulation of this resistance appears to cause an increase in the voltagelevel into far too high levels.Investigations of the trams regulationequipment and its construction have been done. Further have measurements on the overheadline been performed in order to map the voltagevariations during a longer period of time.The result have been showing that the voltagelevel during regeneration often is as high as 880V-920V, more extreme values have not been observed in a large scale. The values are especially high compared to the nominal voltagelevel.

Energy is today a very common topic, not only in Sweden but in the whole Europe. In EU they have given out a directive 2002/91/EG about buildings energy use and throw this they have forced their members to show how much energy their buildings use. In Sweden has the gouvernment established a law (SFS 2006:985) about energy declaration for buildings which demands that the building owner needs to show how much their buildings energy consumption are. Important to know is that this law doesn´t applies for industrial buildings.The report will show what the new law about energy declaration for buildings and appurtenant directions will mean for Riksbyggen. Also energy calculations will be done to be able to compare Riksbyggen buildings with the new law and directions.

This master thesis studies how much the cycle time, i.e. the time it takes for an industrial robot to perform a given task, can be reduced if an extra degree of freedom (DOF) is added to the robot system. The extra DOF consists of a linear track, which is supposed to be used in an optimal way. The problem has been studied using simulations in the robot simulation tool RobotStudio. To be able to run an optimization in Matlab, with the RobotStudio simulation cycle time as the object function, communication between Matlab and RobotStudio has been set up with an interface written in Visual Basic.

Having an ileostomy can affect the quality of life. Quality of life is defined by Siri Naess as being active, relating well to others, having self-esteem and having a basic mood of happiness. The nurse?s task is to focus on the stoma care and work in a holistic way. The aim of the study was to describe how adults with permanent ileostomy experience their quality of life.

This degree project was conducted in collaboration with Gremo AB located in Ätran.The aim of the project was to develop a solution to secure quality and to help assemblingthe locknut holding the vertical hinge on the harvesters and foresters from Gremo.At this time the nut is assembled manually by the aid of an overhead crane. The nut istightened differently from time to time, and there was no specified torque to which it istightened. Another present problem was the locking washer which sometimes getsdamaged during assembly, when this happens the procedure has to be started over fromthe beginning. The current assembly procedure is very time consuming and lengthy forthe employees.Our task was to design a machine that could tighten the nut to a specified torque with amargin of error of ± 3%. The assembly procedure will be held simple and the timerequired at a minimum.The project started by developing several principle solutions, the one solution that bestmatched our specifications were developed to a primary solution.Today we have started manufacturing and assembling our prototype.