This master thesis is an analysis of how the amount of health centers per inhabitant has changed since the Swedish government implemented a new health care reform in 2010. The reform implies a free choice of health centers in the Swedish regions and opens up the market for private firms. The purpose of the thesis is to study the effects of the different financing systems toward the health centers in the regions. The models are based on theories of the need of health care. Two of the independent variables which are studied are income and age.

Eutrophication of the Baltic Sea and Swedish lakes remains a major problem despite many years of effort to reduce the emissions of nutrients. One major source is waste water systems, especially private sewage systems. These sewages accounts for a very large share of nutrients per capita in comparison with citizens connected to larger sewage treatment plants. Norrtälje community has the greatest number of private sewage systems in Sweden. Discharges of nutrients, especially phosphorus, to the Baltic Sea from these sewage systems are significant.

Drain water heat recovery is an uncommon measure in multi-unit residential buildings. There istechnology available for the purpose but the knowing and experience of the heat recovery systems islittle. The purpose of this thesis is to evaluate the future potential of drain water heat recovery inmulti-unit residential buildings.A major part of the multi-unit residential buildings in Sweden were built during modernismen andrekordåren (1940?1975). Many of the buildings have worn out drain and water supply systems andmany are in need of a general refurbishment.

Arbetet har utförts på ABB i Ludvika med avsikt att förbättra revisionsprocessenför kontroll och skydd. En revision är en ändring på ett godkänt och klarmarkeratobjekt. Då objektet i fråga redan kan vara levererat till kund och man behöver göraen ändring krävs en strukturerad process för att utföra denna ändring. Processen föratt göra detta är i dagsläget komplicerad och kräver en hel del administrativt arbete.Processen använder sig utav ett antal program för lagring och databaser så som,Lotus Notes, HiDraw Studio, och HiDra32.Avdelningen för kontroll och skydd är i fasen att övergå till ett annat elCADsystem, Engineering Base. Detta är också en av anledningarna att man önskar en nyprocess för revisionshantering.Arbetet bestod till en början av inlärning av den dåvarande processen.

Wastewater treatment is increasingly controlled by the Swedish environmental quality objectives, adopted by the Swedish parliament. There is a need for a sewage system that can fulfill stringent requirements concerning the environment, recycling and resource use and hygiene. Additional environmental aspects in recent years are the impact of climate change, new knowledge about the effects of pharmaceuticals in water, the need for improved wastewater treatment and increased recycling of nutrients to agriculture. This report has, from a future scenario of the year 2050, analyzed seven different systems for wastewater treatment and treatment of compostable biowaste from households in Eskilstuna. A future scenario was chosen based on that within a forty year period new challenges may arise which can result in higher demands on sewage treatment than those we see today. Another reason why the future scenario was established is that changes in wastewater treatment systems are slow to establish. The analysis is mainly focused on the economical aspects but environmental aspects such as emissions to receiving waters and potential recycling of plant nutrients has also been evaluated briefly.

This thesis aims to investigate SAAB AB´s possibilities to use synthetic instruments in their test systems. The reason for this is reducing costs and the risk of obsolescence which is common when test systems operate for several decades.The market around synthetic instruments has been explored in the search for suitable hardware and software. Software has been developed in LabVIEW and synthetic instruments have been created with the help of IVI-drivers. The hardware consisted of PXI-instruments (Waveform generator and Digitizer), connected to a computer using a fiber optic link and PXI-chassi. The created instruments was then compared to common instruments used today, and the comparison turned out well.

ERP system is the information technology that has had the biggest impact in companies? development and way of working in today?s world. ERP system is divided in several applications with a modular software design that allow people in every department in a company to store and retrieve information accurately and in real-time. This master thesis investigates attitudes toward ERP systems among business organisations and ERP suppliers with the overall purpose of analysing to which extent a new ERP system will bring change in the business process. The purpose of this thesis is to make a survey of attitudes toward ERP systems among business organisations and ERP suppliers.

When different type of programs are developed one wants to make these adjustable to future changes and requirements. It must be done a good design of the program from the beginning to make it possible to continue development of it without having to redo big parts of it to high costs. In the area of object orientation there are design pattern, which can be used to design systems that can be adjusted to new changes in an easier way. I have in this thesis chosen to take a closer look at how to design a program that sends SMS to cell phones through a system of an operator. One requirement on the program is that it has to be possible to change what operator to send though in an easy way.

The aim of this report is to investigate, on the basis of two consult agencies perspectives, what the possibilities and obstacles are to integrate the work with antagonistic and accident related risks. The report is based on two consult agencies where each agency´s work procedure is represented by a risk management method. The work with accident related and antagonistic risks is analysed and evaluated compared to four different components. The components are risk management process (IEC´s and FEMA´s model), driving forces, education and competence, and resources to control risk management with COSO?´s ERM framework.

As an amateur it can be difficult filming from several angles at the same time as this requires several cameras. It´s also hard to film at occasions when it´s not appropriate to manoeuvre the camera manually. Systems for solving these problems already exist, but it´s either more expensive, professionalsystems or cheaper systems with limited functionality.The purpose of this project is to develop a cost efficient solution to the problem above that offers a better functionality then existing commercial systems. The biggest difference from existing products is the wireless video feedback from the camera to the remote unit.The result of the project is a system consisting of two units, a manoeuvre unit with a cradle for the video camera and a remote unit from which the operator can control pan and tilt of the video camera.Communication between the two units is wireless.On the remote unit there is a joystick and a display mounted. In addition to this, there is also an IR receiver that is capable of reading the signal from the cameras own remote and sending it to the manoeuvre unit.The manoeuvre unit is equipped with one motor to control the tilt function and one motor to control the pan.

Examensarbetets frågeställning berör användarnas medverkan i Requirements Engineering (RE). Under RE-fasen skall samtliga krav på det kommande systemet tas fram från intressenterna. En viktig intressentgrupp i kravutvinningsarbetet är de kommande användarna av systemet. Resultatet av RE-fasen är en viktig faktor som påverkar hela den fortsatta utvecklingsprocessen samt hur lyckat det slutliga systemet blir.Detta examensarbete innebär en undersökning av vad användarrepresentanterna anser om use case-modelleringen i RE-processen. Undersökningen har påvisat att användarrepresentanterna är positiva till use case-modellering som arbetsmetod för att kartlägga kraven.

This thesis has been carried out within the bachelor program for mechanical engineering at Karlstad University in collaboration with BAE Systems in Karlskoga. The purpose with this work was to design a mechanism and associated parts for loading and unloading of shots between primary and secondary magazine in BAE's new 40mm's ship gun.Parts designed or redesigned among other things a transfer mechanism for shot at loading and unloading, well as a hatch mechanism which makes the shots do not fall out of the primary magazine when making separate use. Various important details have been designed to maintain a good functionality of the mechanism.The construction work has mainly been carried out in the CAD software Solid Edge and its associated FEM module. The construction work has also been carried out on rough calculations for constructed details in order to ensure that they meet the stringent requirements of military use in tough marine environment. Two of the most critical parts of the structure where analyzed with the FEM module for estimating the stresses in the material at the applied load.The final design, which is a result of the thesis, meets the requirement specification and the set targets.

Problem: Our opinion is that it is important to consider about usability in system development. In this thesis we will focus on usability in point-of-sale systems. The point-of-sale system we base this thesis on is Extenda Retail. Our case study is performed on Ica Kvantum in Bromölla, which implemented Extenda Retail about two years ago. Purpose: The purpose of this thesis is to figure out what important factors there are to consider, in usability aspects, when developing point-of-sale systems, with focus on the cashier.

When a disaster occurs the main focus is on the loss of human lives. Here the environmental effects have been in the centre of attention. This work has had two main purposes. The first one was to formulate attributes, variables that together present a complete picture of the consequences that an event has had on the environment. The other main purpose was to investigate how people value the impact that a disaster can have on the environment.

This thesis has been carried out within the bachelor program for mechanical engineering at Karlstad University in collaboration with BAE Systems in Karlskoga. The purpose with this work was to design a mechanism and associated parts for loading and unloading of shots between primary and secondary magazine in BAE's new 40mm's ship gun.Parts designed or redesigned among other things a transfer mechanism for shot at loading and unloading, well as a hatch mechanism which makes the shots do not fall out of the primary magazine when making separate use. Various important details have been designed to maintain a good functionality of the mechanism.The construction work has mainly been carried out in the CAD software Solid Edge and its associated FEM module. The construction work has also been carried out on rough calculations for constructed details in order to ensure that they meet the stringent requirements of military use in tough marine environment. Two of the most critical parts of the structure where analyzed with the FEM module for estimating the stresses in the material at the applied load.The final design, which is a result of the thesis, meets the requirement specification and the set targets.