At present Getinge can offer a new generation of trolleys that they produced in 2011. The trolley used to Getinge various autoclaves and has the primary task to help the user/sterilization personnel to transport shelves or baskets, with or without cargo, from a packing table to the autoclave. The purpose of this thesis has been to develop a primary solution how the docking process between Getinge trolleys and autoclaves can be improved. The work has in most part followed Fredy Olsson principle and primary construction method. The work has included product research, study visit and development of a requirements specification, to satisfy Getinge, their clients and circumvention products requirements.

As part of an internship at Ericsson, this report was written to enhance the understanding of how it is to develop a system that is well established at the workplace. To improve an already existing system is not always as easy as many developers may think. In this report the pros and cons of developing an already existing system has been researched and analyzed. Do note that the results are only from one development of a specific system and that comparison of other developments has been made from other reports and not from experiencing it firsthand. It was found that the choices made can have an impact on further developing and it is important to write down what has been done.

To be able to measure high-surge voltages and transients with short rise times youneed measuring instruments with a high sampling frequency and large Bandwidth.These surges and transients occur primarily at lightning but can also occur at forexample at connecting errors at an electrical switch-gear. This report describes thework with finding two solutions for measuring and log data from these surges andtransients. One temporary solution where a measurement program has beendeveloped. A second solution where different company solutions have been analyzedto decide which fits best. For these measurement solutions two solutions for bringingdown the voltage has been used.

Title: A study about the purchasing process of ITLevel: Master thesis in Information Technology and Business Administration, 15 hp, EIK024Authors: Emelie Johanson and Mikael LindströmTutor: Peter Ekman, Mälardalens HögskolaKeywords: IT-investment, purchase, decisionProblem: In the last decades the amount of IT investments increased and has become an important resource within most organizations. IT gives the ability to compete and could also be a condition for many to be able to compete. In different businesses it could vary in where they put their focus when they choose an IT investment. This thesis examines how the purchase process of IT looks. How does processes differs in a bigger company versus a smaller company? From these two perspectives this study examined these research questions: Who makes the decisions whether or not an IT solution should be purchased? What aspects decide when companies are to choose between different IT solutions? Where in the purchase process do problems usually emerge?Purpose: The purpose of this thesis is to describe and analyze the purchasing process of IT from a business perspective.

The voltage regulation in Fortum Distributions medium voltage network in Stockholm does not work satisfactory. This results in too high distribution voltages with many customer complaints as a consequence. The reason is the model responsible for compensating for voltage drops in the distribution network. Despite several adjustments Fortum has not been able to find the source of the high voltages and has therefore appointed an investigation in the form of a thesis work.The aim of this investigation is to locate the error and to produce a proposal regarding the solution of this error using the existing system, common industrial knowledge, state of the art research and the option to use voltage readings from the different substations.The conclusion of this master thesis is that the largest contribution to the high voltage levels is made by the large compensation for distribution loses. Furthermore an additional error in the model has been found.

The main goal of this project was to develop some sort of a diverter for pipestransporting waste in a vacuum system. This unit was supposed to be both cheap andeasy to serve/exchange worn out parts. With a limited space to install the pipeexchanger, the challenge was to keep it as compact as possible without constructingbends with to small radius or to sharp angles as this would wear out the system a lotfaster than planned. The system was also supposed to be able to handle clothes andscrubs from hospitals. Having too much sharp edges or angles would tear the clothesapart.

The purpose of this master thesis has been to find different solutions to the design of a headlamp with a cluster of three or possibly four high power LEDs (Light Emitting Diodes). During the work, two different problems have been considered; how to design a lens in order to shape the light beam in a desirable way, and how to design a cooling system which will lower the temperature of the LEDs as efficiently as possible, still taking into account the geometry set by the optical solution as well as other given geometries. The results presented in this thesis are partly the outcome of a literature study, but derive mainly from a number of tests and measurements made on two test rigs and one concept prototype..

Information handling has been a key issue for different companies for a long time. Electronic Data Interchange (EDI) is used to transfer different business documents from one company to another. This is done in such way that the information itself is separated from how this information is stored and handled in the companies internal systems. As different companies have different systems there is a need for a standardised format for this exchange. There is a big difference between EDI-systems based on what kind of EDI-standard is used. The most common standard in Europe is EDIFACT, but with increased interest of using the Internet for business communication there is a need for a standard that is adjusted for use over the Internet.

A helicopter based system equipped with a millimetre-wave fire control radar is studied for improvement of the detection probability for moving ground targets. The system is a pulse doppler radar that sends out the electromagnetic wave in repetitive pulses. The frequency in which radar sends this pulse is called Pulse Repetition Frequency (PRF). The velocity of the moving targets is measured by spectral analysis of the pulses received. With this sort of system some targets will not be possible to detect.

The gas turbines in the Swedish secondary reserve are reaching the end of their technical lifetime, hence alternative solutions need to be considered. One of the solutions thought to have the greatest potential is the use of so called consumptionreduction. By entering contracts with large consumers, agreements are made to reduce consumption in the event of major disturbances in the power system and thus being used as a secondary reserve. This thesis investigates the feasibility of consumption reduction as part of the secondary reserve. This has been achieved by developing a requirement specification for the disturbance reserve and by studying the technical and economic potential for consumption reduction among a range of consumers.The technical potential for consumption reduction that fulfils the requirements for participating in the secondary reserve are on average 750 MW in SE 3 and 98 MW in SE 4.

ABSTRACTThis project thesis has been written at the request of Mälardalens University, Västerås.The aeronautical engineering students at Mälardalens University and the pupils of Hässlö upper secondary school, all gets the opportunity to perform a computation lab with a real turbojet engine during their study. The goal of the lab from the University is that it should give the students applied experience from the theory part of which has been tought in the course ?Aircraft Engine Technology?.                      The pupils of the Hässlö upper secondary school are performing simpler calculations from the measured values of the equipment. This turbojet engine is located at Hässlö airport in the premises of Hässlö upper seconday school.Since the installation 1989, the engine has lost both thrust and reliability. This makes the theoretical computations made by the students inaccurate.

This project concentrates on musicians who work in a professional music studio.The task of this project was to design a new headphone system called Foldback system.The advantage of this system is that all involved in a music project could influence their ownlistening during the project. With a couple of adjustments should each and everyone get theirown individual listening from their headphone station.This report shows different methods, theories and results that came along in development ofFoldback system. The project has resulted in a finished product that will be in use atStudiomega..

This thesis describes teh solution of two problems regarding safety on powered lawnmowers; protectning the users from injury when using the lawnmower in slopes, and when cleaning the cutting blade.The task was carried out through initial studies on a representative lawnmower. A generation of ideas followed with an evaluation to select the best solution. The winning concept was further developed to reach acceptable performance. The word resulted in a functioning prototype utilising an original way of detecting inclinations without incorrect signals. It c an serve as a platform for further development into a product.The work gives insightful experience of solving real-world problems, and especially to deal with situations where several variables and their effects are unknownPlease note that several parts of the work are confidential, and have therefore been removed from the thesis..

Sweden is seen as one of the world?s most feminist societies. In January 2009 all grounds of discrimination were merged into a common law; Diskrimineringslagen. This paper examines representations of gender discrimination, linked to feminist perspectives, in the Parliamentary debate on Sweden?s new discrimination legislation through a discourse analysis.

In many products a compromise between ground clearance and the required space to store the product has to be made. This problem attracted the attention of the authors of this thesis.The objective of this project is to develop a functioning solution to a foldable wheel. The solution should be applicable to several types of product groups. A limitation for this work has been made so that the work only covers solutions for lighter vehicles.The purpose is to drive this project forward, so that a solution can be found. Furthermore the purpose of the report is to clarify how the authors proceeded to design and construct the wheel according to a fixed specification.