Highly polluted urban storm water from e.g. highways can contain large amounts of heavy metals that may cause harm if they are discharged into recipients. To remove the heavy metals a possible low-cost method that does not require much maintenance, could be the use of reactive filters with filter materials consisting of industrial residues or other cheap mineral based materials. Dissolved metal ions are removed by reactive filters through the processes of ions binding to active sites on the Surface of the filter materials, or by formation of insoluble precipitates.The ability of CaO-treated granulated blast-furnace slag, iron oxide coated sand, olivine and nepheline to remove seven heavy metals (Cr, Cd, Cu, Ni, Zn, Pb and Hg) from urban storm water was studied. Initially batch experiments were performed where the effect of pH, dissolved organic carbon (DOC) and dissolved ions on the adsorption efficiency was studied.

This study investigates three different methods for evaluating MOE,Modulus of Elasticity, in field measurements. The purpose is toinvestigate the possibility to use dynamic measurement methods infield measurements that hitherto (2010) has been performed with staticmethods. The objects of investigation are 20 glulam beams. The firstfield measurement took place in november 2007 and applied a staticmethod based on the standard SS-EN 408. The second measurement,described in this study, took place during summer 2010, and appliedstatic as well as dynamic methods.The MOE of wood is affected by a range different factors.

This project explores how artificial landscapes as parks and squares above ground can save space by using the vertical voids in urban environments and how they can create spatial and social as well as ecological qualities and connections. Hybrid landscapes are a phenomenon of current interest within the field of architecture and urbanism. Architecture as Surface, where facades and roofs become possible to tread, is a relatively recent occurence that has over the past few years become an increasingly common sight in architectural magazines and on international architecture exhibitions. Many of my selected reference projects have often been associated with sensational contemporary design trends generated by advanced computer software. But the phenomenon is also a result of other different currents of change that exist within today?s society, such as densified cities with a lack of open space, which is also expressed in architecture.

In 2009 The National Land Survey of Sweden, Lantmäteriet, commenced a project intended to provide a new digital elevation model (DEM) of Sweden. The method chosen for the project was airborne laser scanning (ALS). In addition to information about the land Surface the project will also provide information about the forest, this as a by-product. This data can be used to estimate forest variables such as height and volume. The estimates are often more reliable than what is standard today. This study is based on interviews with employees and members of the forest owner association Södra in southern Sweden.

GE Healthcare wants to investigate whether additive manufacturing would be an alternative method in their workshops in the Umea? plant. Additive manufacturing is called 3D printing in everyday language and manufactures details by building them up layer by layer in an automated machine. The purpose of this work is therefore to investigate how mature additive manufacturing methods are and how they could be used at GE.The work has been divided into three parts. The first section investigates how additive manufacturing would work in the production workshop at GE.

A group of two people, Jelena Durkan and Johan von Heideken, have worked together on an assignment from the company August Lundh AB. The company manufactures plastic products for all sizes of catering establishments. The basis for this thesis is a pre-study which shows that many of the users would be more drawn to the plates that the company manufactures, if there was a motif on the plates.This thesis will present the method of application for the motif that best benefits the company, with regard to the requirements placed on the motif, application method and the costs. The group found five relevant methods that were more carefully examined and compared to each other. Those are:Laser engraving, Hot-stamping, Injection molding, In-mould labeling and Pad-printing.The tools that have been used to solve this problem are: Requirement specification, QFD and OEE.

This explorative study focuses on young, university attending males (22-27 years) and their understanding and pratice of the classic tail coat. It is based on five qvalitatively interpreted interwievs with a total of six participants, and through open questions regarding individuality and identicalness, limits and possibilities and inclusion and exclusion, a masculininty of a less contemporary hue takes shape. These conversations have revealed the tail coats potential of respresenting a male stereotype that can set a foundational and minimal standard for inclusion. Above this layer these males can then manifest and negotiate their masculine position in a homosocial hierarchy which decides the amount of passage, privilieges and confirmation of self- worth received for the wearer. These negotiation is performed by value bearing symbols (such as medallions, cordons and the like) allowed by the wearer and by the actions that systematically ensure that the lines of the tail coat are watched and unbroken.

The river Göta Älv reaches between Vänern and Gothenburg and is the main raw water source for Gothenburg that supplies about 700 000 people with water. To protect and maintain a high water quality, continuously samples and water analyses are made throughout the river. In 1998 a protection area was founded between surte and Lärjeholm where the raw water intake is. This was made to increase the awareness of the importance to protect the water. However, there is a lot of contribution of untreated stormwater to Göta Älv within the protection area.Göteborg Water and Sewage Works commissioned this thesis where two areas, Tagene industrial area and Kärra residential area, with untreated stormwater outlets within the protection area are studied.

The aim of this thesis was to answer a number of questions about the environmental consequences of aircraft de-icing. A further aim was to suggest how the environmental consequences due to the release of de-icing fluids can be measured and reduced.The main impact of the aircraft de-icing on the environment is due to the large oxygen demand for the degradation of glycol based de-icing fluids which are released in the environment. The effect of the increase in oxygen demand depends on where the degradation occurs in the ecosystem. In a sensitive ecosystem, the large demand of oxygen could provide an anaerobic environment which would be harmful for many types of organisms.In order to reduce the negative effects of the applied de-icing fluid, there is some type of collection system at every regular airport in Sweden. The methods of collection can be divided into two general groups, hydrological isolation or vacuum sweeper trucks.

GE Healthcare wants to investigate whether additive manufacturing would be an alternative method in their workshops in the Umea? plant. Additive manufacturing is called 3D printing in everyday language and manufactures details by building them up layer by layer in an automated machine. The purpose of this work is therefore to investigate how mature additive manufacturing methods are and how they could be used at GE.The work has been divided into three parts. The first section investigates how additive manufacturing would work in the production workshop at GE.

There is convincing research which shows that the enzyme alkaline phosphatase (ALP) has a central role in the mineralization of bone, more precisely that its catalytic activity is needed in the process. ALP is found on the Surface of matrix vesicles where the mineral is formed. One theory about the function of the enzyme is that it binds to fibrous collagen in the bone and thereby incorporating the mineral into the bone. The purpose of this study is to establish whether ALP binds to collagen. If this is the case, more elaborate studies around this will be performed.

Discharge of untreated wastewater leads to unnaturally high levels of nitrogen and phosphorus in rivers, lakes and the sea, which results in unbalanced ecosystems with eutrophication and lack of oxygen. Part of the phosphorus in Surface waters is coming from on-site wastewater treatment from scattered households with unsatisfactory purification. Blast furnace slag is a by-product from iron production, and has in laboratory trials showed good phosphorus binding capacity. To test blast furnace slag as a reactive filter media for phosphorus separation in a full scale experiment, a wastewater treatment plant has been built behind the picnic area at Ångersjön alongside the road E4 in central-eastern Sweden. The plant contains two parallel lines, one with blast furnaces slag and the other with Filtralite-P as phosphorus sorbent. Both filters have showed decreasing phosphorus purification effect with time in spite of a low wastewater load.

Background: Since1994, the EU NickelDirective is limiting the release of nickel from objects that are in prolongedcontact with skin. Despite this, nickel is still the most common cause of contactallergy in industrialized countries. This could implicate that other productswith short contact to the skin, which are not restricted by EU´s legislation inREACH (Registration, Evaluation, Authorisation and Restriction of Chemicalsubstances), could be a source of nickel or cobalt exposure. There is no limitfor cobalt release within REACH. To determine if there is cobalt or nickelpresent on the Surface of a material and if metal can be released in contactwith the skin, there are quantitative and qualitative methods, such as the DMG(dimethylglyoxime)-test, the cobalt spot-test and a method for releasedetermination according to EN1811.Objectives: Laptops are not included in the REACH legislation.

This thesis examines how to improve the exhibition of products within retail for clothes and gift articles. The purpose is to investigate and test how light sources and different directions of light affect how the products are perceived regarding their exhibition. Our question formulations are:To what degree does the level of light in combination with the background of the interior design of a shop affect whether a product is perceived more or less attractive?What can we recommend to make the exhibition of products more attractive? From our observations shops nowadays have relatively high levels of light when they expose products on vertical areas. We have looked on the recommendation from ?Energimyndigheten? in order to see what they think is important when designing retail lightening.

Limträ är ett material som består av sammanlimmade lameller av konstruktionsvirke. Limträ tänjer gränserna för vad man kan bygga med trä, genom att erbjuda balkar med längre spännvidd och med större tvärsnitt än vad som annars vore möjligt. Genom förstärkning av limträkonstruktioner med kolfiberkomposit skulle lastkapaciteten kunna höjas ytterligare. Tillämpnings-området för förstärkning av limträkonstruktioner skulle kunna ligga inom nyproduktion eller kapacitetshöjning av befintlig konstruktion. Syftet med detta examensarbete är att undersöka förstärkningssystemets potential vid förstärkning av limträbalkar med kolfiberkompositstavar.