This thesis aims at determining the heat losses in a property vent stack and its roof valve. Upon request of a company, the vent stack is analysed for possible heat recovering solutions to be implemented, while relining of the drain system is executed and with a suitable payback time for the economic investments. The heat loss calculations are based on data for properties that are located in the Stockholm region, but also easy to change depending on the situation. The calculations are done on pipes made out of cast iron, which still is the most common type of drain pipe in Sweden, and these are the pipes that relining is usually made on. The calculations that needed to take several variables into account have been done in MatlabR2014a and the thermos dynamical properties that were used in those calculations have been extracted from EES.Three different types of heat losses in the vent stack have been taken into consideration in this thesis.

The EU Council adopted in 2007, environmental and energy goals with the aim of them must be met by 2050. This, in combination with those of the Swedish government 15 enacted environmental goals is supposed to lead the way for the Swedish environmental work.This report has examined measures in properties in the Swedish Cooperative Housing Society (SKB) stocks.The report discusses a range of measures that might be appropriate to apply on the properties to make them more energy efficient.One of the measures discussed, the vent whose primary purpose is to create a good indoor environment for the residents but is also where the most energy is lost.Another measure discussed is insulation of the building envelope on the estate to make it more energy efficient. To put extra insulation on the building envelope is important because of the large amount of energy that is lost through the walls, ceilings and floors.Future actions that may be implemented is individual billing of heating and hot water. This system has been used in European countries since the 70's and today the EU wants to increase the own individuals control over their electricity costs. This has led to a discussion whether to implement the system in Sweden or not.However, there are a number of equitable measures to be sorted out before the system can be used in any great scale.Finally, it is important to remember that environmental measures should be the primary and the pursuit of cost reductions the secondary otherwise you risk the environmental work to be counterproductive..

At Uppsala university scientists have during the last years developed and built wave energy converters. This project is called "Lysekilsprojektet". The development has come so far that they are currently investigating how to gain profit in a mass production. For that reason they want to automate as many steps in the production as possible.The winding of the stator is one part that is being automated using industry robots. The stator is cable wound unlike many other generators.

The climate changes that are occuring in the world have resulted in that the EU callingfor a 20 % reduction in energy consumption to the year 2020, to reach that goal theEU want the public sector to go forth as a good example. Västfastigheter owns andmanage the hospital buildings in the Västra Götaland region. To be able to reducetheir energy usage Västfastigheter has hired several consulting firms to chart out theenergy consumption on each hospital building. The biggest energy savings potentialhave been calculated and what the cost will be to perform each action. The energyaudit have been completed and stand as the decision basis for Västfastigheter?s choiceon which action packages that should be implemented.

The purpose of this master thesis is to investigate different types of measures for making buildings more energy efficient and to estimate their profitability. The calculations were performed with the building simulation program VIP+ and the evaluation of the profitability with the life cycle cost method. Furthermore, it was examined how losses in the distribution of secondary systems of district heating can be avoided. Options to replace district heating with a local district heating system based on bio-energy have been investigated. The possibilities of achieving more efficient thermal energy consumption and production for the chosen estate were also examined.The object of the study has been a residential estate with 133 detached houses in Uppsala, built in 1974.

In the Swedish market, there is a wide selection of herbs as supplement to the horse´s feed. A trend today is that many companies are marketing herbal remedies with allegations of medical effects. If you want to sell the product for that purpose it must be verified and approved as drug or natural remedy by the Medical Products Agency. Some herbs may contain active substances. Nevertheless, only a few studies have been conducted on single herbs to investigate safe doses for horses.

To fulfill the climate target that EU and the Swedish government have decided to apply, it becomes increasingly important that the energy efficiency of existing buildings and making new buildings energy efficient as possible. Of Sweden?s total energy consumption in 2011 was 40% used by residential and service. Of the 40% of the energy consumption was 60% used for heating and domestic hot water. A report from year 2012 shows that one reason why the heating volume is so great could be due to underestimating on the energy consumption for the heating in the planning of the building.

5-hydroxytryptamin (5-HT) is biochemically derived from Tryptophan. Kynurenic acid and quinolinic acid are also known metabolites of tryptophan. 5-HT is considered to play a role in depression and today selective serotonin reuptake inhibitors (SSRIs) are used for treatment of depression. 5-HT may also play a role in pain perception. The aim of this study was to investigate whether a supplement of tryptophan may affect conditions such as depression and/or pain.

AbstractThis report intends through a case study to investigate if lightweight concrete isappropriate as main material in the outer wall of a seven storey residential building.A technical design is carried out in accordance with the definitions and requirementsfor passive houses, given by FEBY?s1 ?Demand specification for passive houses?.A literature review is also carried out for a comparison between regular bolt wall andlight weight concrete wall, with a focus on the safety of moisture.The lightweight concrete block used in the report is as a celblock produced by thecompany H+H Sweden AB.The methods used have resulted in compliance with requirements andrecommendations from authorities. Calculations of energy, noise and moisture riskassessment has been carried out.The work has resulted in the conclusion that the lightweight concrete itself is notable to isolate in the extent necessary to obtain chosen U-value of 0,1 W/m2 ° C,without getting to thick. Therefore additional insulation is needed. There are fewrelevant reference objects built with only light weight concrete.

AbstractThis report intends through a case study to investigate if lightweight concrete isappropriate as main material in the outer wall of a seven storey residential building.A technical design is carried out in accordance with the definitions and requirementsfor passive houses, given by FEBY?s1 ?Demand specification for passive houses?.A literature review is also carried out for a comparison between regular bolt wall andlight weight concrete wall, with a focus on the safety of moisture.The lightweight concrete block used in the report is as a celblock produced by thecompany H+H Sweden AB.The methods used have resulted in compliance with requirements andrecommendations from authorities. Calculations of energy, noise and moisture riskassessment has been carried out.The work has resulted in the conclusion that the lightweight concrete itself is notable to isolate in the extent necessary to obtain chosen U-value of 0,1 W/m2 ° C,without getting to thick. Therefore additional insulation is needed. There are fewrelevant reference objects built with only light weight concrete.

The Swedish government has introduced a goal to reduce the energy intensity by 20% to the year 2020. To reach this goal actions need to be taken throughout the energy sector which includes residential and commercial buildings. This thesis considers the possibility to reduce the energy usage in a building located close to Uppsala. The analyzed building is a combined office, cafeteria and entrance and was completed about half a year before this project started. Therefore the measures presented for a more energy efficient building are presented as measures for future constructions.Simulations have been made in VIP-Energy, a dynamic energy calculation program.

In developing countries such as Vietnam the population consumes more animal products for example milk and meat than before which requires greater livestock production. Ruminants contributes to more methane emission which creates a dilemma between food production and its environmental impact. By feeding ruminants with nutritive crops which humans can not assimilate the animal performance will increase in terms of better growth and milk production without inpinging on food that can be consumed directly by humans. Increasing animal performance reduces methane emission in terms of amount of methane in kg-1 milk and meat which today is much greater in developing countries than developed countries. The aim of the study was to investigate tropical tannin-rich legumes for their potential as a feed supplement for ruminants made in vitro.

Background: The most energy efficient houses today are so called passive houses. These houses achieve high energy-efficiency partly by having well insulated walls. U-value describes the amount of heat transfered through a building element, the more insulation, the smaller U-value. A typical passive house wall have a U-value of 0.10 W/m2,°C. The passive houses are primarily made as small family houses and not as a block of apartments.

As break downs of production transformers are costly and often result in long outages it is essential for reliability of operation that the transformers are manufactured to be robust. The aim of this M.Sc. thesis is to investigate if deviations should be made from the standard IEC 60076 ? Power Transformers in order to describe a robust large power transformer for procurement.The investigation has been conducted in three stages. In the first stage a definition of the term robust was developed in consultation with the client Vattenfall Vattenkraft.

A study to optimize insulation thickness for stock-, industrial- and office-buildings for external walls and roof in an economical perspective has been conducted on behalf of DynaMate. DynaMate?s role is to maintain all Scania?s buildings. Analysis has also included other parts of the building envelope, such as windows, exterior doors and industrial doors. In this thesis, three different types of exterior wall constructions has been investigated, these are a sandwich design consisting of sheet metal and a another one consisting of concrete, as well as a wall of concrete with a coating of plasters.