This technical report describes the master thesis in material engineering called ?Testing of surfaced hardened materials conceivable for gears and shafts?. The work extents 20 academic points. Land systems Hägglunds manufactures and sells different kinds of combat vehicles and terrain vehicles. Since the demands for bigger and stronger vehicles increases all the time, so are the demands on shafts, gears and other transmission details.

Vanadin i konverterslagg är idag ett växande problem i Sverige. Framförallt på grund av att det inte finns någon verklig avsättning för slaggen då den förbjudits som jordförbättringsmedel och då förväntade gränsvärden gällande utlakning förhindrar att den används inom andra områden såsom vägbyggnation. Det finns idag flera vanadinproducenter som använder sig av förblåsning av råjärn för utvinning av vanadin, bland andra Pan Steel i Kina och Nizhniy Tagil Iron and Steel Works i Ryssland. Det koncept som framförallt studerats i detta examensarbete bygger på att först reducera den varma LD konverterslaggen från SSAB till en vanadininnehållande metallfas. Därefter skall en vanadin-fosfor och vanadin-järn separation ske genom att selektivt oxidera vanadinet till en vanadinrik slaggfas.

The report aims to describe the austenitic stainless steel Sanicro 25 from a thermomechanical point of view. The thermal and mechanical properties of the material make it suitable for use in coal ? and thermal power plants. By the use of Sanicro 25 it would be possible to bring the efficiency of these plants up while bringing the carbon emissions down.A material model is created from material testing and validated through simulation in the finite element software Abaqus. The model that has been derived describes the material behavior during loading and stress relaxation for the first cycle in a thermomechanical fatigue test well.

This report is a study made at Pallco AB. Pallco is a subcontractor that is specialized on steel and aluminium components.The aim of the report is to show an improvement proposal that leads to a reduction of the storage and improve the flow through the production of one item that is a part of a product that Pallco manufactures.With the increasing competition from other countries who can manufacture with lower costs must Swedish companies try to make theirs manufacturing as efficient as possible and remove all waste. By using the tools of Lean Production it is possible to reduce the costs and increase the efficiency.The method we used is value stream mapping. A map of the present condition has been made and then different improvement proposal were discussed. A map of a future condition has also been designed..

I det här projektet analyseras huset Röken, uppe på det Småländska höglandet, en plats med mycket historia. Från 1600-talet då en bräcklig fred gör att huset byggs till då huset moderniseras under mitten av 1900-talet och blir inrett med många möbler från Ab Svenska möbelfabrikerna, som bara låg några kilometer från platsen. Detta leder fram till en undersökning av familjen som äger huset och till Jan Strand, min far, idag den enda permanent boende där. Projektet har mynnat ut i möbeln ?Beach? avsedd att användas då Jan i ensamhet njuter av jazzmusik uppe i sin sons rum..

At the beginning of 2011, Sweden started using the European rules for structural design, the Eurocodes, instead of the previous national rules. In both the previous rules and the Eurocodes, it is possible to dimension concrete columns using tabled values. However, the required cross section measurements have increased considerably. Moreover, it is possible to dimension concrete columns using calculations, however, this is unusual.The development of a fire in a fire cell can be divided into the growth stage, the fully developed fire and the cooling phase. The duration of each phase, as well as the temperature, is dependent on a number of factors, e.g.

This is a final year project considering constructional techniques for joining cavity walls. The project is related to an ongoing scientific programme about the restoration of The City wall of Visby located on Gotland. The programme was set by Riksantikvarieämbetet as a reaction to a collapse of the outer masonry wall shell which took place in February 2012.The City wall of Visby is a medieval fortification built out of limestone during the 13th century. The wall is constructed as a cavity wall with two separate masonry shells connected to each other through an intermediate core. During the 14th century the wall was heightened which lead to a higher stress, especially in the outer wall face.

In recent years, moisture damages have been noticed in rendered, undrained stud walls. The design is built on the principle one-stage tightening which means that there is no air gap in the construction. The damages have occurred when water has permeated through the rendering in leaking connections and fittings for windows, doors, canopies, balconies, terraces and awnings. Behind the plaster carrier, which consists of either polystyrene or rigid mineral wool, plasterboard has often been used as a wind protection barrier. In many cases the wind protection barrier and the underlying wooden studs have been exposed to mould and in some cases even rot.

The thesis that follows is performed in collaboration with Nitator in Oskarström.The factory in Oskarström focuses on laser cutting, robotic welding and surfacetreatment of steel for the automotive industry.The project aims to streamline the flow of materials in production by automatingthe movements of the forklifts, running to and from the interlayer, and betweenworkstations.The project started with a systematic literature search. The literature searchshowed the research position around the AGV-system. Also a review of studentliterature was made, so that a suitable method for practical implementation couldbe developed and applied. Selected method uses both quantitative and qualitativeapproaches, which is analyzed by using triangulation.The work has resulted in a modified layout of the current facility in Oskarströmthat can be used for the implementation of the AGV-system. It has also resulted inthe tender documents and profitability calculation from several of AGV-suppliers..

The purpose of this thesis is to investigate the degree of influence of holes in the web of steel beams with long spanson weakening of their bearing capacity. Making holes in the web of the beam generally reduces the bearing capacity of the beam. However, it might be necessary seen from both an architectural perspective as well as from a building services perspective by creating an opportunity for building installations.The objective of this thesis is to examine how much an I-beam can be weakened without sacrificing safety and functionality. The investigation has been done by using Finite Element Method through commercial software.The regulation for structural design of building structures in Sweden used to be specified in the document known as BKR. But this was replaced by the European norm Eurocode back in May 2011.

EVA, Equine Viral Arteritis, was diagnosed for the first time in 1953 in USA. The disease gained international interest in 1984, when there were several outbreaks of abortion at Thoroughbred studs in USA. EAV, Equine Arteritis Virus, is an RNA virus in the Arteriviridae family. There is only one serotype of EAV but several strains and the strains have different virulence. EAV is transmitted in two different ways: by aerosols, or by venereal transmission.

Hos LuCoil Steel AB, dotterbolag till SSAB Tunnplåt AB, värmebehandlas bl.a. stål för att ge det speciella egenskaper som gynnar dess formbarhet vid efterföljande behandlingar. Denna värmebehandling av stålet som kallas för mjukglödgning eller sfäroidiseringsglödgning är en väldigt tidskrävande process, där strukturella förändringar i materialet sker och utvecklas med tiden. Syftet med detta arbete har varit att hitta optimala värmebehandlingscykler för fyra olika stålsorter där kraven på materialegenskaperna uppfylles och samtidigt undersöka hur utvecklingen av mikrostrukturen med tiden påverkar dess egenskaper. För att simulera den industriella glödgningsprocessen hos LuCoil utfördes försök i en laboratorieugn och vidare utfördes hårdhetsprov, dragprov och analyser av mikrostrukturen i svepelektronmikroskop för varje glödgat material.

This study is a part of a larger project where the aim has been to evaluate different methods to assure the quality in stallion semen, due to the fact that some stallions in horse breeding have poor semen quality. The increased use of transport semen requires new methods to ensure good semen quality. In this part of the project the viability and concentration in fresh and cooled semen was examined with NucleoCounter SP-100. A comparison between two different commercially available semen extenders, Kenney?s and INRA 96, was made.

Norrborns Industri AB in Bollnäs manufactures truck trailers with the brand Parator. One of their trailers is Parator LX 10-20. The trailer is designed to transport hooklift containers with the option to tip loose goods such as gravel, asphalt and seed. The container is mounted on a frame which is placed on the chassis. To reduce weight a redesign of the trailer is needed.

This master thesis was conducted during the spring of 2014 at Atlas Copco Rock Drills AB in Örebro. The purpose of the thesis was to develop a simulation model of the rotation system for a hydraulic rock drill. In the future, the model will be used to investigate the phenomena called ?jerky rotation?. In order to validate the simulation model a test bench was designed and tests were made.