An often encountered problem when implementing a mass flow regulator in a rolling mill is the one with measurement of speed. The most widely used solution is to fit a pulse counter to a wheel that is in contact with the strip. Common problems with this design are for instance scratch marks on the strip and problems with the flatness measuring system.  One way of circumventing the aforementioned problems would be a non-contact measuring system. The market of today only offers systems based on the Doppler principle.This report evaluates three different systems for non-contact speed measurement. Important areas in the evaluation have been the ability to operate under normal rolling conditions, integration in existing control system and how well the sensor can be fitted to the rolling mill.

An often encountered problem when implementing a mass flow regulator in a rolling mill is the one with measurement of speed. The most widely used solution is to fit a pulse counter to a wheel that is in contact with the strip. Common problems with this design are for instance scratch marks on the strip and problems with the flatness measuring system.  One way of circumventing the aforementioned problems would be a non-contact measuring system. The market of today only offers systems based on the Doppler principle.This report evaluates three different systems for non-contact speed measurement. Important areas in the evaluation have been the ability to operate under normal rolling conditions, integration in existing control system and how well the sensor can be fitted to the rolling mill.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

This thesis has been performed at Uddeholms AB with the purpose to investigate theparameters affecting the formation of inclusions during the manufacturing of a low carbonmanganese-steel.A follow-up, steel and slag sampling and evaluations in microscope have been done for a totalof five heats.The results for each heat have been evaluated in relation to the theory from the literaturesurvey and suggestions for changes in the process to reduce the amount of inclusions whichhave a negative effect on the steel quality have been given.The project extends over a large process where many parameters affect the formation ofinclusions. However, a tendency that a higher addition of alloys seems to increase the totalamount of inclusions before and after the vacuum degassing is seen.The majority of the studied inclusions seem to approach the composition of the top slag aftervacuum degassing. Ladle glaze may cause the inclusions which had a different compositioncompared to that of the slag.A high or low ladleage together with a high argon flow during vacuum degassing seems todissolve particles from the refractory which later on get trapped inside the inclusions.The floatation for two heats has been studied where a short floatation seems to give a higheramount of inclusions in casted material.In machined material so called stringers were found. The main composition of those stringerswas pure alumina. Inclusions with a composition of pure alumina were not found in the liquidsteel, thus the pure alumina inclusions must be formed during the casting.

The company Olofsfors AB manufactures drive belts for forest machinery, known as ECO-Tracks, and abrasion-resistant steel and cutting edges for graders, excavators and tractors, known as Bruxite and SharqEdges. Manufacturing these products requires the steel to be heated and molded, then submerged in water and hardened. The water used in the hardening of steel is pumped to the process from pits below the floor and then pumped back to the pit after it?s been used. Since the temperature of this water rises after being used to harden the steel the temperature of the pumping pit needs to be adjusted to maintain its setpoint of 21°C.

Forest fertilization had its peak in the late 60´s, when almost 200 000 ha was fertilized annually. The silviculture of today has high demands for timber production at the same time as the demand for nature conservation increases. It means that it?s necessary to produce more volume in smaller areas in the future. The use of DGPS equipment has in modern forestry in Sweden become more and more common.

The last decade has created an increasing pressure on companies to decrease their impact on the environment and to increase their effectiveness of recycling the company?s resources, especially for the steel industry. Companies have also started to realize the economic aspects of an effective internal reverse logistics. In the past the value of an effective internal reverse logistic was something that companies tend to underestimate and there are few academic studies done in this area. The purpose of this essay has been to identify key factors to create an effective in plant storage, transport, sorting and handling of returned steel. From these factors a generalized model for creating an effective return steel flow will be developed.

Blast furnace is the heart of every steel plant. Steel production is based on the blast furnace process, as it is where the iron is extracted from the iron ore and turned into liquid iron, which will subsequently be used to make liquid steel. Therefore, without hot iron, steel can not be produced. Blast furnaces in this process are supplied among others with pulverized coal. Raw coal should be prepared for the blast furnaces in the form of fine coal powder.

To create multifunctional buffer strips along a watercourse in an economically sustainable way requires consideration of many different factors. In this plan we have selected pollutant reduction as the main purpose of the buffer strip. We have also strived to achieve minimal income loss due to reduced production, increased biological diversity, good game preservation that leads to higher income from hunting, aesthetical satisfaction and possibility to profit from available subsidies. This is done mainly to make landowners/farmers more interested in creating buffer strips along water courses.As sand is the dominant type of soil in the area, the water course is less affected by surface runoff compared to if the soil would be clay or some other finer texture. Game preservation and subsidies have therefore been the main factors when establishing the width of the strip, because these require wider buffer strips in some cases.

Suggestion for a new operahouse in stockholm, förslag på nytt operahus i stockholm. Stockholmsoperan..

To create multifunctional buffer strips along a watercourse in an economically sustainable way requires consideration of many different factors. In this plan we have selected pollutant reduction as the main purpose of the buffer strip. We have also strived to achieve minimal income loss due to reduced production, increased biological diversity, good game preservation that leads to higher income from hunting, aesthetical satisfaction and possibility to profit from available subsidies. This is done mainly to make landowners/farmers more interested in creating buffer strips along water courses. As sand is the dominant type of soil in the area, the water course is less affected by surface runoff compared to if the soil would be clay or some other finer texture. Game preservation and subsidies have therefore been the main factors when establishing the width of the strip, because these require wider buffer strips in some cases.

SCA has today almost 300 000 hectares of their forest land planted with lodgepole pine(Pinus contorta var. latifolia). Due to initial extensive planting in the 1970ies the area oflodgepole pine forests in the thinning age has grown rapidly from the end of the 1990ies.During the years 1996-2005 first commercial thinning of lodgepole pine at SCA took place.The goal of the hereby presented study was to investigate the growth and stability in thosefirstly-thinned lodgepole pine stands a few years after thinning. Furthermore, the objectivewas to investigate the relationship between stand stability and different stand parameters.Additionally, lodgepole pine stem quality was estimated.The study is mainly based on the data collected during an inventory project carried out atSCA in 2008. Altogether 91 lodgepole pine stands in northern Sweden were measured afterthe first thinning.

The aim of this thesis is to investigate the correlation between the price of electric power and investments within the Swedish basic industry. Using regression analysis, the authors test for correlation between the electricity prices and the basic industry, defined as the pulp and paper industry, the mining industry, the steel and metal industry and the basic chemical industry. Moreover, five variables found in the literature on investment decisions are being used as a means of comparison. The results suggest that the electricity price affects the investment decisions within the basic chemical industry as well as the steel and metal industry. On a more abstract level, this thesis contributes to the understanding of one of the properties of the Swedish GDP..

AbstractThis study aims to investigate the applicability of well-recognized supply chain strategies based on product characteristics. Choosing the right supply chain strategy can be the difference between winner and loser in today?s competitive climate and science offers several recommendations as to which aspects that should be considered. Fisher (1997) and Christopher and Towill (2002) suggest that supply chain strategies should be based on what kind of product the company is handling and that, in order to know which strategy is the most appropriate, the products must be categorized. Some criteria developed for the categorization are lead time, forecast in demand and profit margin.

The aim of my thesis was to do a Life Cycle Assessment (LCA) of an average thread tap that is manufactured by Dormer Tools AB, and to create a practical model that the company can use in order to study other thread taps from an environmental perspective.The method of LCA is used to investigate the environmental effects of a product during its life cycle. This is a gate-to-grave analysis with focus on steel and thread tap manufacturing, coating procedure, use, waste management and transports. Three common coating types were compared separately. Steel manufacturing answers for the highest energy and raw material consumption under the life cycle of the thread tap. Its emissions contribute to global warming, acidification and eutrophication above others.