AbstractThe future of ethanol is depending on good solutions for the production. ENA energy power plant produces electrical power and district heating by heating biofuel. By building an integrated bioenergy plant surplus steam could be used to produce ethanol as fuel to vehicle.This would mean that ethanol is produced renewable energy and the energy for the process derives from the surplus of power.  ENA energy, MDH (the University of Mälardalen) and the energy authority has initiated a research project were different bioenergy combinations integrate with existing power plant.  As a part of the project which size an integrated factory should be to gain the best efficiency for the plant was investigated. Consideration will be taken to the cost of the production in order to be competitive to the price of imported ethanol.  Etanolens framtid vilar på bra lösningar för framställning.  I ENA energi kraftverk i Enköping produceras el och fjärrvärme genom eldning av biobränsle.  Genom att bygga ett integrerat bioenergikraftverk där skulle man kunna använda överskottsånga till att framställa etanol som fordonsbränsle.

Det här är ett examensarbete som handlar om en fastighet som står på Norra Kungsgatan 37-43 som har både en värmepump och fjärrvärme för uppvärmning. Värmepumpen används i första hand och fjärrvärmen används som spets när värmepumpen inte räcker till. Detta är en ganska ovanlig kombination. Syftet med arbetet är att ta reda på om detta är en bra lösning och om lösningen är lönsam. För att få fram hur stort fastighetens energibehov är så görs beräkningar utifrån fjärrvärmedata från tidigare år samt en gammal värmepump som är utbytt sedan 2011.

AbstractThe future of ethanol is depending on good solutions for the production. ENA energy power plant produces electrical power and district heating by heating biofuel. By building an integrated bioenergy plant surplus steam could be used to produce ethanol as fuel to vehicle.This would mean that ethanol is produced renewable energy and the energy for the process derives from the surplus of power.  ENA energy, MDH (the University of Mälardalen) and the energy authority has initiated a research project were different bioenergy combinations integrate with existing power plant.  As a part of the project which size an integrated factory should be to gain the best efficiency for the plant was investigated. Consideration will be taken to the cost of the production in order to be competitive to the price of imported ethanol.  Etanolens framtid vilar på bra lösningar för framställning.  I ENA energi kraftverk i Enköping produceras el och fjärrvärme genom eldning av biobränsle.  Genom att bygga ett integrerat bioenergikraftverk där skulle man kunna använda överskottsånga till att framställa etanol som fordonsbränsle.

This is a report written for an examination project C-level, on the subject of energy. The examination project is a product of the FVB Sweden AB (district heating bureau). It started with a meeting with Stefan Jonsson FVB Sweden AB, were he explained the content of the project, and from this a presentation of the problem was made. The problem that needed to be solved was how they could control the valves in the system to provide heating to everyone in the system. The valves are often oversized so the pump in the heating plant would have to be enormous to be able to provide enough flow to be sufficient, if everyone in the system had there valves fully opened. I came up with two solutions to the problem, one was a wireless network that could keep track of the valves and the other solution was an extra sensor that was placed on the radiator.

This report is the result of a thesis work carried out on the Risifrutti production at the company Procordia Food AB. The thesis is at a master level and is the final work for the author to receive a Master of Science in Innovative production at Mälardalen University. The thesis comprises 30 credits and has lasted for 18 weeks. The thesis is mainly a research on whether it is possible to perform an Environmental Value Stream Map (E-VSM) in a food processing industry and an evaluation if the tools E-VSM and Green Performance Map (GPM) are useful in this type of industry. An extra part to this research is to use the results from the E-VSM and give Procordia Food AB information on improvement potentials in the Risifrutti production. The author has found it difficult to collect some of the quantitative data to the E-VSM, mainly regarding energy, but by using the Value Stream Mapping (VSM) tool and other Lean tools the author was able to identify and quantify several wastes in the Risifrutti production. Recommendations for improvements based on these wastes have been given to the company. In the research part of this report the utility of the Value Stream Map, Environmental Value Stream Map and Green Performance Map in a food processing industry have been analyzed. The author has found that the Value Stream Map has been a useful tool since waste and unevenness in the tact of the production has been identified. The Environmental Value Stream Map and the Green Performance Map are also great tools when a company wants to analyze their environmental impact and then invest in environmental improvements. However, no profound energy analyzes has been done in the Risifrutti production because of the lack of energy meters for steam, electricity and compressed air in the production lines..

I have chosen to work with drag hose system and try to find an alternative to spread manure with a usually tank system, see if you can make a profit and what advantage and disadvantage the system has. The purpose whith the project has been to try to make a system that can spread manure at better occasions than farmers do today and above everything make a financial addition. Today it is just a heavy work and takes a lot of time. I have counted on investment costs and carefully examined what equipment you need. I have not the technical details in my project, I have just tried to understand how it is to spread manure with drag hose system today. What is drag hose system? You put a hose in your manuretank, connect it to a pump that is driven by a traktor or stationary engine. You place a hose that reach the field were you are going to spread.

Climate change is the modern society?s common issue. The developed countries areconsuming more than what is sustainable, and the climate change due to the use offossil fuels can be seen clearly. EU has specified goals, in order to stop furtherdamage, which demand that every member state have to reduce its energyconsumption by 20 % before 2020 and 50 % before 2050, relative to 1995.The Swedish government uses a number of instruments to encourage reduction in theusage of energy, but every individual has to contribute to reach the goals.With increasing energy price the cost of living is going up. A lot of people are lookingfor ways to save energy and not be affected as much by the increasing price.Investments for insulation, replacement of windows and replacing old heating systemfor a new efficient heat pump is getting more and more common.This thesis is about investigating the possibilities in becoming independent from buyingenergy for households.

In a sustainable society the use of renewable energy and recycling of materials is of high importance. Wastewater treatment plants use large amounts of energy in the processing of wastewater. This study seeks to evaluate wastewater as an energy resource and to examine treatment plants potential to become sustainable energy producers. The study is based upon the internal processes of Himmerfja?rdsverket.

Smärta är ett fenomen som inte bara påverkar patienter fysiskt utan även psykiskt. Kvinnor som genomgått mastektomi upplever att smärta påverkar deras livskvalité. Humörsvängningar, dålig sömn, depression, ångest och rörelsehinder är vanligt förekommande symtom som följd på postoperativ smärta. Syftet: Syftet med denna studie var att belysa vad sjuksköterskan kan ge för olika behandlingar och omvårdnadsåtgärder vid smärta efter mastektomi. Metod: Studien genomfördes som en litteraturstudie där författarna granskade sexton vetenskapliga studier.

I detta exjobb har en testplattform skapats för att kunna testa, utvärdera och jämföra olika pumpstyrningar i torr miljö. Testplattformen består av en simulerad pumpstation till vilken befintliga pumpstyrningar av valfri modell kan kopplas, det vill säga ett Hardware-In-the-Loop-system. De främsta fördelarna med en sådan plattform är flexibilitet, snabb feedback samt möjligheten att återskapa exakt samma förutsättningar för olika pumpstyrningar.Testplattformen har implementerats i LabVIEW på en PC som kommunicerar med pumpstyrningshårdvara via ett I/O-kort för analoga och digitala signaler.Det simulerade systemet konfigureras genom val av bland annat pumpar, pumpsump, inflöde och rörsystem. Utifrån de inmatade värdena och styrsignaler från pumpstyrningen simuleras sedan bland annat systemets flöden, energier och temperaturer. Nivån i sumpen, och övriga insignaler till pumpstyrningen, återkopplas från simuleringen.

AbstractThe future of ethanol is depending on good solutions for the production. ENA energy power plant produces electrical power and district heating by heating biofuel. By building an integrated bioenergy plant surplus steam could be used to produce ethanol as fuel to vehicle.This would mean that ethanol is produced renewable energy and the energy for the process derives from the surplus of power.  ENA energy, MDH (the University of Mälardalen) and the energy authority has initiated a research project were different bioenergy combinations integrate with existing power plant.  As a part of the project which size an integrated factory should be to gain the best efficiency for the plant was investigated. Consideration will be taken to the cost of the production in order to be competitive to the price of imported ethanol.  Etanolens framtid vilar på bra lösningar för framställning.  I ENA energi kraftverk i Enköping produceras el och fjärrvärme genom eldning av biobränsle.  Genom att bygga ett integrerat bioenergikraftverk där skulle man kunna använda överskottsånga till att framställa etanol som fordonsbränsle.

Heat and power stations are often in need of optimizations. A simulation model is a tool for findingways to optimize the plant. The scope of this diploma work is to develop a simulation model ofBoiler 5 at Mälarenergi AB. Boiler 5 is a circulated fluidized bed boiler that was taken into service inyear 2001. Among the included parts in the boiler are cyclone, convection part andINTREX-chambers.

Quality assurance for Scania engine componentsScania engines have become one of the world?s most renowned corporations in themanufacturing of engines. This is mostly due to the quality and performance thatScania have shown. However, this does not stop Scania from trying to achieve moresuccess in the fields of development and research to assure the quality of theirengines.The purpose of this thesis is to show how Scania ensures the quality of the enginecomponents, both those who made externally and internally at Scania, also inclusivethe manufacturing and assembly process.Three engine components were examined: D16 block engines, water pump andXP-Iinjectors. The study included the whole process from the step of supplying therow materials to the last step in production functional test.In this thesis an investigation of how other companies are working with qualityassurance was conducted.

Parasiter i magtarmkanalen och framför allt nematoder, orsakar världsomfattande produktionsförluster hos lantbrukets djur. För att kontrollera nematodinfektioner används anthelmintika. En överanvändning av anthelmintika har resulterat i att vissa nematoder utvecklat resistens. Därför är det väsentligt att vi tillämpar en sund användning av anthelmintika som inte gynnar vidare resistans utveckling. Makrocykliska laktoner är den substansgrupp som används flitigast.

The Swedish pulp and paper industry meets higher demand for energy efficiencyi mprovements with increasing energy prices and changes in the Swedish renewable energy certificate system. One action of energy efficiency improvement is by using secondary heat, that otherwise would have been treated as waste heat, for use in a system with lower temperature demands. The aim of this Master´s thesis is to identify possible secondary heat sources in a typical Swedish pulp and paper mill and to investigate what economic benefits the secondary heat will provide when being used for pre heating of wood chips to a kraft digester.The Master´s thesis focuses on three secondary heat sources; dry warm air, warm water and moisture saturated warm air located inside the pulp or paper mill. Two types of kraft digesters are simulated within this study, a typical Scandinavian digester and a modern twin vessel steam phase digester.Due to quality aspects and low temperature level drying is the drying technology with dry warm air rejected. Using warm water in direct contact with wood chips increases the quantity of water to the evaporation plant and thus reduced pulp or paper production and is therefore also rejected.