The purpose of this thesis is to investigate the fatigue life of two components in different hydraulic quick couplings. The crack which initiates the fatigue failure usually occurs in the bottom of one of the threads. Thus, the threads in the coupling are carefully investigated. A few different approaches for determining the fatigue life are studied for each component. CAD (Computer Aided Design) models for both components are created and analyzed with FEM (Finite Element Method).

The Earths climate is changing at a higher rate, i.e between 1861 and 1994 the annual mean temperature in Scandinavia increased with 0,68º C and according to recent climate models the annual mean temperature is likely to rise with another 3º C during this century.A warmer climate in many ways is associated with changing conditions for lake ecosystems. An expected higher water temperature and a stronger summer stratification of the water column increases the risk of anoxic conditions at the lake bottom. Thus anoxic conditions are likely to cause a phosphate leakage from the sediment, i.e. a higher internal loading of phosphate.In this project, the extremely warm summer of 2002 has been used as an example for a possible scenario for a future climate. By comparing levels of phosphorus in the summer of 2002 with a ten-year median value, a phosphorus related sensitivity to climate change has been analyzed for 55 Swedish lakes.

The aim of the study was to investigate if methane emission in a constructed wetland changed in a diurnal pattern correlating to temperature, humidity or light conditions. The gas measurements were carried out with a static chamber technique. The wetland (in Nykvarn outside of Linköping, Sweden) takes care of wastewater to reduce the nitrogen loads. Measurements were carried out at three different occasions in the summer of 1998 on two sites in the wetland. One site was close to the inflow, inhabited by Lemnaceae, and another site was located further downstream inhabited by the emergent macrophyte Typha latifolia.

The county hospital of Dalarna has for the last couple of years carried through a process of digitalization. The result is that within the county it exists image plate systems from two different manufacturers. In an attempt to create a tool for dose optimization and dose surveillance the county of Dalarna would like to investigate if the exposure index from Agfa and Fuji is suitable as a dose indicator. An investigation of the exposure index, S, from Fuji has already been done. This thesis has been continuing the investigation by evaluating the stability of the exposure index, lgM, from Agfa.

At present Getinge can offer a new generation of trolleys that they produced in 2011. The trolley used to Getinge various autoclaves and has the primary task to help the user/sterilization personnel to transport shelves or baskets, with or without cargo, from a packing table to the autoclave. The purpose of this thesis has been to develop a primary solution how the docking process between Getinge trolleys and autoclaves can be improved. The work has in most part followed Fredy Olsson principle and primary construction method. The work has included product research, study visit and development of a requirements specification, to satisfy Getinge, their clients and circumvention products requirements.

This thesis investigates in which way principles and theories of usability is revelant when evaluating interactive systems for children aged 10-12. It also investigates whether there are specific factors that you should keep in mind while developing interactive products for the targeted group.The results of the qualitative study shows that priciples and theories of usability is relevant when evaluating interactive systems for the targeted group. However there is one concept that is more significant than the others. Our study shows that our targeted group is sensitive to time-consuming activities such as loading times etc. which has to do with the efficiency of the system.

Introduction: Dolomite AB was in need of a dummy arm for crutch testing, to complement their existing test capabilities. Background: A large number of people need crutches on a daily basis. For them it is essential that their crutches do not fail. ISO (the International Organization for Standardization) conducts ongoing work to guarantee the durability and function of e.g. crutches.

The shooting sport is one of the most widespread sports in the world and it isbeing practice in most countries. Based on their own experiences, in competition -and hobby shooting, the client M4Solutions found a demand and need for ashooting target that is manufactured in Sweden.The purpose of the project has been to develop, with the help of Marcus Walldén,two shooting targets from idea to finished product. These two shooting targets,Plate Rack Target and Dueling Tree, would each be equipped with a mechanicalresetting system but will in the future have the ability to be provided with anelectronic resetting system.The project from the client was divided into two theses. One of these two, writtenby Marcus Walldén, focused on the tripod parts and the overall design work forboth Plate Rack Target and Dueling Tree. The thesis that is presented in thisreport have focused on resetting systems, the design of protective plates and otherperipherals for both shooting targets.This work has primarily been in CAD environment where design, constructionand development has been given free rein.

This thesis has been carried out within the bachelor program for mechanical engineering at Karlstad University in collaboration with BAE Systems in Karlskoga. The purpose with this work was to design a mechanism and associated parts for loading and unloading of shots between primary and secondary magazine in BAE's new 40mm's ship gun.Parts designed or redesigned among other things a transfer mechanism for shot at loading and unloading, well as a hatch mechanism which makes the shots do not fall out of the primary magazine when making separate use. Various important details have been designed to maintain a good functionality of the mechanism.The construction work has mainly been carried out in the CAD software Solid Edge and its associated FEM module. The construction work has also been carried out on rough calculations for constructed details in order to ensure that they meet the stringent requirements of military use in tough marine environment. Two of the most critical parts of the structure where analyzed with the FEM module for estimating the stresses in the material at the applied load.The final design, which is a result of the thesis, meets the requirement specification and the set targets.

In this thesis, a transparent model of the human head has been constructed which was filled with a substance that represented the brain. This model was later crash tested. This was done in order to examine how a transparent model of the human head can be constructed to generate accurate data from crash tests. It was also done in order to examine how impacts on the front of the head can deform the rear of the brain. When a head is decelerating, the brain moves forward inside the skull and may hit the front of the skull.

In this thesis, a transparent model of the human head has been constructed which was filled with a substance that represented the brain. This model was later crash tested. This was done in order to examine how a transparent model of the human head can be constructed to generate accurate data from crash tests. It was also done in order to examine how impacts on the front of the head can deform the rear of the brain. When a head is decelerating, the brain moves forward inside the skull and may hit the front of the skull.

This thesis has been carried out within the bachelor program for mechanical engineering at Karlstad University in collaboration with BAE Systems in Karlskoga. The purpose with this work was to design a mechanism and associated parts for loading and unloading of shots between primary and secondary magazine in BAE's new 40mm's ship gun.Parts designed or redesigned among other things a transfer mechanism for shot at loading and unloading, well as a hatch mechanism which makes the shots do not fall out of the primary magazine when making separate use. Various important details have been designed to maintain a good functionality of the mechanism.The construction work has mainly been carried out in the CAD software Solid Edge and its associated FEM module. The construction work has also been carried out on rough calculations for constructed details in order to ensure that they meet the stringent requirements of military use in tough marine environment. Two of the most critical parts of the structure where analyzed with the FEM module for estimating the stresses in the material at the applied load.The final design, which is a result of the thesis, meets the requirement specification and the set targets.

In this thesis, a transparent model of the human head has been constructed which was filled with a substance that represented the brain. This model was later crash tested. This was done in order to examine how a transparent model of the human head can be constructed to generate accurate data from crash tests. It was also done in order to examine how impacts on the front of the head can deform the rear of the brain. When a head is decelerating, the brain moves forward inside the skull and may hit the front of the skull.

Our greatest interest within crop farming is to grow sugarbeets, that?s why we want to write about something new in this sector. We heard that a new concept had come to Sweden so we wanted to find out everything about this machine. This new technique was a self-propelled cleaning loader for sugarbeets. This machine is supposed to replace a loader and a cleaning machine when the sugarbeets is going to be loaded, cleaned and delivered to the sugerbeet factory. The cleaning loader picks up the sugarbeets with rollers from the pile, which is placed close to the road.

Avdelningen för reaktorteknologi på Alfa Laval har identifierat svårigheter vid förmedlingen av kunskap till potentiella kunder. Examensarbetet innefattar utveckling och produktion av en film avsedd för utbildning och marknadsföring av Alfa Lavals flödesreaktorer, ART® Plate Reactors, för att förbättra Alfa Lavals sätt att förmedla kunskap till och fånga intresse hos potentiella kunder på mässor.Målet med examensarbetet är att filmen ska användas på kemiteknikmässor där reaktorerna ställs ut, och syftet med arbetet var att med mässbesökarnas förkunskaper som bas utveckla en film som väcker intresse och samtidigt fungerar som ett lärandemedel.Genom intervjuer har information om hur mässor går till, önskemål om filmens utformning, samt bedömning av besökarnas förkunskaper samlats in. Dessa intervjuer, samt litteraturstudier inom området för kemiska reaktorer och lärande med animation och kommunikation på mässor har legat till grund för arbetet med framtagandet av filmen.En storyboard utvecklades, och lade grunden för produktionen av filmen som gjordes i samarbete med filmbyrån Upper/First i Malmö. Produkten av examensarbetet, filmen, finns att se påhttp://youtu.be/PyoX3mVXuYc.Nyckelord:Storyboard, Multimodalt lärande, Kontinuerliga flödesreaktorer, Reaktorteknologi, ART® Plate Reactors.