When grains of wheat and rye are conventionally milled, large quantities of bran classified as by-products are left and are mainly used for animal feed. Bran is a complex material composed of the aleurone layer, nucellar epidermis, a seed coat, a fruit coat and a small proportion of the germ and endosperm depending on extraction rate. The bran fraction consists of approximately 40-50 % dietary fibre which can contribute to increase the nutritional quality of human cereal food. It would also be valuable for the food industry to convert by-products as bran to products with higher commercial values. The aim of this thesis was to analyse the content and composition of dietary fibre of heat treated wheat and rye bran according to the Uppsala method with some modifications in order to analyse soluble and insoluble dietary fibre separately. Half of the bran samples were precooked, dried and roasted and the other half dried and roasted (uncooked).

Climate change is expected to lead to increased rainfall and higher temperatures, among other things. This will have a major impact on our cities. Floods can lead to property damage as well as damages to human and animal health. Higher temperatures will increase the frequency of heat-related health risks and premature deaths. The consequences of climate change will be particularly large in our cities because of the city's morphology with a high amount of paved surfaces and buildings that affect the natural processes in areas such as drainage and absorption of solar radiation.

WSP building physics in Stockholm has certified the preschool Temmelburken in Bromma with the system of certification Miljöbyggnad. The rating of the building became BRONZE. In this thesis the preschool has been investigated with respect to the three areas: thermal climate, use of energy and improving of the level of certification. The thermal climate at the preschool has been investigated by a questionnaire survey and by measurements in order to do comparisons between the results from the two investigations as well as with the results of the simulations that WSP has done at the certification of the preschool. The differences between the results from the simulations and the questionnaire survey for winter as well as from the measurement performed with a comfort meter the 19th of March are concidered to be reasonably small since they give rise to the same rating according to Miljöbyggnad.   Operational data for the use of energy for the preschool have been obtained in order to do comparisons with simulations performed by WSP and Svenska Besiktningar AB. The comparison shows that the simulated values for the specific use of energy are lower than what the real specific use of energy would be for the preschool, since just the operational data for the heat energy is higher than the simulated values. At the investigation of the possibility of improving the level of certification it was found that the rating of the preschool can be raised from BRONZE to SILVER by improving the ratings of the ?thermal climate summer? and the ?daylight?.

This pre-study investigates the possibility of U-value measurements through an acoustic method. A hypothesis about an acoustic model built on acoustic theories combined with U-value theories is presented to answer the questions: ? Can U-value theory be combined with acoustic theories? ? Can the coefficient of heat be affirmed trough an acoustic measurement? The idea for this dissertation begun with a logical idea in mathematical similarity, between the coefficient of heat transmission units and sound intensity units. The U-value theory is based on assumptions such as initial resistance for inner walls and initial resistance for outer walls. The resistance in the material is interpreted through sound intensity theory. The argument is built upon mass law theory, which means if the frequency or thickness of the material layer doubles it implies an increase of sound reduction by 6 dB.

The study aims to investigate the feasibility of small-scale electricity production with solar electricity systems, also known as PV (photovoltaic) systems, in Australia. Due to the global warming, sustainable energy has in recent years become an increasingly important issue, both internationally and in Australia. With one of the largest dependencies on fossil energy sources in the world, the country's abundant solar radiation is a possible solution to this issue.Both the technical and the economic feasibility of small-scale PV systems were investigated. On the technological side, the electricity generation, distribution and consumption systems were studied. On the economical side, the parameters that drive the profitability of a PV investment were investigated.

A passive house in Norra Djurgårdsstaden drawn by Tengbom Arkitekter is going to be built. A shaft for airing is needed for a few apartments in the house.The airing shaft is designed for a few two room apartments in the house, which are not able to achieve satisfactory airing, as their outer walls are facing a single direction. The other apartments on the same floor are corner apartments. These apartments do not have the same difficulty with airing since they have their outer walls in different directions, with different pressures at the facades. The airflow in the airing shaft is supposed to be driven only by natural forces, by the sun. The purpose of natural driven forces is to achieve low energy consumption for the house.In this thesis, a design of the shaft for airing has been developed.Initially an open shaft for all apartments was analyzed.

The heating of companies premises is today functional with electrical heating and heating offossil fuel. The energy cost for these kinds of heating in buildings has heavily increased duringthe last years and the influence on the environment has become more visual. This leads to thatenterprises today become more anxious to render energy more effective and find alternativesolutions to their ancient heating systems. This is something that Skandinaviska kraftprodukterAB in Halmstad has become aware of.The purpose with this examination is to find the most cost-efficient and environmental measuresfor the office and workshop premises of SKP AB. Where one of the bigger things is to find agood alternative for their current oil furnace, which was heating the workshop.

This thesis has identified and studied measures to allow for reduced use of electricity in a waste incineration plant in western Sweden. The energy extracted from the waste at the powerplant is utilized and sold in form of electricity and heat. Technical and environmentally the combined heat and power plant is by today's standards among the leading waste incineration plants in the world. The owners are constantly striving to improve the efficiency of the waste incineration plant. They have seen the opportunities for savings in reducing internal usage of electricity.

Heat is distributed to the district heating customers through pipes with water as a heat carrier. The district heating system is complex. To decide what is leakages from the district heating net versus what is the water consumption of the plant, is difficult. Therefore, the purpose of this master thesis is to establish a model where the district heating net?s leakages but also the water consumption of the plant can be followed daily. The project is performed at Vattenfall´s district heating power plant in Uppsala. Information is gathered through discussions, drawings of the plant and guided tours of the plant.

This report contains results of our study at CTC in Ljungby. CTC produces heating products such as boilers, heat pumps and additional products to their heating systems.The purpose of the report is to make a proposal how CTC will supply their new production line for heat pumps with materials. The proposal includes a production layout and a scheme for how to place the material in the production storage.The new production line will produce two different products and both of them have several variants. The line will also have a mixed flow, so the products can be produced in a random order. These conditions demand that the production line has great flexibility and that the material to all the variants can be stored in the production storage.With these conditions as input we made a layout proposal to the company.

The report comprises two separate parts:part 1:  Temperature needs for district heating in the paint shop for axles in building 210part 2:  Energy and low temperature waste heat solutions in heating and cooling systems for   building 64 with surroundingsThe paint shop for axles in part 1 has air quality requirements in places for coating of axles. Toachieve desired air properties there are different process ventilation systems, which consist ofventilation coils for heating and cooling, plus air humidifier. The ventilations coils for heating usedistrict heating. Today the ventilation coils use water of 100°C to achieve necessary air demands inthe coating boxes. This part of the report investigates whether the existing system would achievethe air requirements with a water temperature of 75°C instead of 100°C in the ventilation coilsduring the coldest parts of the year.

Abstract In order to make the modern agriculture less dependent on non-renewable external inputs, it has to rely more on ecosystem services. The agricultural system produce not only food, fiber and fuel, it also generates other ecosystem services such as e.g. photosynthesis, recycling of nutrients, influencing local microclimate, pollination, biological control and detoxification of noxious chemicals. This study is an attempt to get a better understanding about the interaction among different ecosystem services and different habitats capacity to generate them. An evaluation of eight different methods is done. The ecosystem services studied are the ability to absorb solar energy, biomass production, botanical diversity, decomposition and natural predation of aphids.

The building sector accounted for around a fourth of the total energy usage in Sweden in year 2010 (Energimyndigheten, 2012). Therefore it has become very interesting to achieve a lower energy usage in residential buildings. One way to achieve that is to build so called passive houses. By being very well insulated and have low leakage through the walls, they can reduce the energy usage for heating with a substantial amount. The first passive house was built during the 90?s in Germany; and in Sweden the first passive house was built in Gothenburg 2001.

This thesis is about a part of the marquetrytechnique, scorching. Scorching is made by heating up something, put a veneer into the heated substance and make a controlled burning. This technique is old but still used today and have according to me great potential for development. In my work I wanted to give the scorching greater room then I earlier have seen. I wanted the scorching to be the dominant ingredient for a decorative element in a piece of furniture or an interior.

Geothermal energy can be extracted from an aquifer, where the groundwater is used as heatexchange medium while heat and cold are stored in the surrounding material in the aquiferand to some extent in the groundwater. Application of aquifer storage for the use ofgeothermal energy is mainly used in large scale facilities and is limited to sites with suitableaquifers in the form of ridges, sandstone and limestone aquifers.Löwenströmska hospital in the municipality of Upplands Väsby, north of Stockholm, islocated nearby the northern part of the Stockholm esker. This means that it can be profitableand environmentally beneficial for the hospital to examine the possibilities of aquifer storagein the esker material next to its property.The purpose of this master thesis has been to investigate if geothermal energy storage with aseasonal storage of heat and cold can be applied within Löwenströmska hospital?s propertyarea using groundwater modeling. A hydraulic groundwater model was constructed inMODFLOW based on a simplified conceptual model of the groundwater system.