As a consequence of increasing wind power installations in the Nordic grid the last years, the need for regulating power has become larger. In the Nordic grid, regulating power is mainly provided by hydro power. One part of the regulating power is called frequency control, which ensures that the grid frequency is stable and close to 50 Hz.However, setting the turbine into frequency controlled operation may cause stress and wear of the components in the mechanical control system. Frequency controlling implies large and frequent servo forces and longer travelling distance of the sliding bearings in the Kaplan turbine.Based on one selected Kaplan turbine, Selsfors G1, measurements and MATLAB calculations have been performed in order to determine forces and movements of the linkage system. With these forces and movements as input, stresses and fatigue have been determined as well as sliding distances, bearing pressures and wear of bearings during a typical lifetime of 40 years.The results indicate that no severe wear exists on the bearings during 40 years of service.

BACKGROUND: Today?s societal changes, including high rate of change and increasing information flows, are increasing the demand on the individual mental capacity. It becomes increasingly difficult to analytically process all the different dilemmas and everyday decisions as individuals have a limited mental capacity available to make these decisions. Thus, it has been suggested that ego-depleted relies more heavily on intuition, which is less burdensome, when making decision. However little is known about to what extent intuitive decisions differ from analytic.

Energy issues are constantly increasing attention in today's society. People's impact on Earth isentered in more contexts. Many discussions are about how the entire social structure needs to bestreamlined in order to achieve sustainability. The residential and service sector accounts for 39 % oftoday's total energy consumption in Sweden and the increasing electricity prices have made buyersmore interested in energy issues.There are many buildings in need of refurbishment today, including all the apartments that werebuilt in the 1970s to reduce the housing shortage at the time. 650 000 apartments of one millionapartments were built during the so-called the one million program and is currently in need ofrefurbishment.

Today, we use BKR and BBK 04 when designing concrete structures inSweden, which will, in the near future, be replaced by Eurocode 2. When you are designing buildings, you will use Eurocode 2 Part 1-1 and with this new standard, some new rules and general rules will be necessary to adopt. To examine how BKR and BBK 04 tells apart from Eurocode 2 when designing concrete structures, one beam and one column with often common dimensions, is studied. The beam is designed with consideration of (considerate to) durability at bending moments, shear forces and control of cracking. The column is designed with consideration of durability at eccentric axial load and bending moments in cross section on account of (due to) geometric imperfections. BBK 04 has gone one step closer to Eurocode 2 than earlier editions and the things that are different, when calculating reinforcement, is how they use the partial factors.

Before the European construction standards were introduced in January 2011, it was mainly themethod in BBK04 that was used for calculating punching capacity in concrete structures, and in lesscommon cases the method in BHB. The method of BBK04 is easy to use and have had the samestructure since the first was published in 1979. The Concrete handbook method (BHB) where usuallyonly used when a higher punching capacity was needed and the cross-sectional height where fixed,calculations using this method entails more work, but will in return usually give a higher capacity. Italso allows the use of shear reinforcement to increase the cross-section capacity. The method ofcalculating punching shear in EC2 differs largely from the methods of BBK04 and BHB.

This thesis is about a part of the marquetrytechnique, scorching. Scorching is made by heating up something, put a veneer into the heated substance and make a controlled burning. This technique is old but still used today and have according to me great potential for development. In my work I wanted to give the scorching greater room then I earlier have seen. I wanted the scorching to be the dominant ingredient for a decorative element in a piece of furniture or an interior.

Calculated and measured energy in residential buildings is going to differ. The reason to this may be due to many factors. In this study there is a study on how these factors affect the energy use in a building. To get an insight in what defines energy, there is first a description of energy supply both worldwide and used in Sweden, followed by a description of the energy balance. In this study energy will be studied in residential buildings only.

Svenska Kraftnät is (together with the other transmission system operators of the Nordic power system) responsible for keeping balance between the generated and demanded power in the Nordic power system. Spontaneous load variations and system disturbances, however, lead to power imbalance followed by frequency variations. The frequency deviations can be limited to an acceptable level by the spinning reserve, mainly by hydro power control. But there are also other system properties which have a great influence on the frequency and system stability. The frequency and voltage dependence of the loads have a direct influence on the power balance.

This Master thesis is about a postal- and telegraphic building in Eskilstuna, Sweden. The construction methods for the specific building and buildings in general from the same time are described. The purpose of the report is to describe the loads acting on the building and how it has been built and why it has been rebuilt during the years. After this, possibilities of reconstruction and adaptation for today?s demands can be evaluated.

In published studies it is found that the fuel consumption on a forwarder is relatively constant, on time basis. A certain variation between different sizes of forwarders occurs as well as between different working elements. The aim of the study was to establish a forwarders comparatively fuel consumption when driving on road and in the terrain, loaded and unloaded, with high and low gear and with high and low speed as well as with hydrostatic and hydrodynamic transmission. A hypothesis was that low rpm gives lower fuel consumption on distance basic, at all trials. The test driving was made with a Hemek 750 which is a three geared hydrostatic machine and with a Hemek 700 which is a hydrodynamic machine with six gears.

Vattenfall Heat Uppsala runs the waste incineration plant in Uppsala, which produces district heating, process steam, district cooling and electricity. Vattenfall Heat Uppsala has decided to introduce an energy management system with the aim to increase the energy efficiency of the plant. The basis in such a system is to make an energy mapping.In this thesis an energy mapping has been performed at the waste incineration plant with the aim to identify and determine the size of energy flows. The investigated energy flows are used fuel, produced and used steam, produced district heating and cooling. Also the use of electricity to run the processes has been investigated.

This thesis is based on a case study for the real estate manager Mimer in Västerås. Mimer provides a great deal of this city?s rental apartments. Many of their buildings have ventilation systems with a type of heat-recovery called ?heatpipe?.

In a sustainable society the use of renewable energy and recycling of materials is of high importance. Wastewater treatment plants use large amounts of energy in the processing of wastewater. This study seeks to evaluate wastewater as an energy resource and to examine treatment plants potential to become sustainable energy producers. The study is based upon the internal processes of Himmerfja?rdsverket.

This project operate an environmental assessment of total waste was conducted by using a life cycle assessment (LCA), that examines the environmental benefits of recycling production waste from Atlas Copco at Stena recycling. Atlas Copco is a company engaged in the development and production of rig-mounted hydraulic breakers and handheld air breakers and handheld motorized rotisserie. Stena recycling is a recycling company engaged in recycling, processing and refining of metals, paper, electronics waste and hazardous waste.The purpose of this study is to focus on Stena customer Atlas Copco and evaluate environmental benefits between to recycle and not to do it. The result shows that the total energy gain, resulting from the recycling of waste fractions, lands at 6 990 089 MJ, corresponding to drive 3 times around the Equator with a truck (40 t). The result shows that recycling 3040 kg paper provides an energy gain of (38 600 MJ) compared with burning paper (19 500 MJ) is 19 100 MJ, which corresponds to heat a house for 11 weeks.

Idag ställs stora krav på företag att vara miljömedvetna och resurseffektiva i sin verksamhet. Vid mjukpapperstillverkning används stora energimängder och inom industrin har det under många år funnits en strävan att energieffektivisera processer och att tillvarata spillenergi, bland annat genom värmeåtervinning. Valmet Tissue Technology Center i Karlstad har idag en pilotmaskinen utan värmeåtervinningssystem. Den här undersökningen gjordes i syfte att ta reda på hur stor återvinningspotentialen är för värmeväxling i pilotmaskinens torkpartier, bestående av Yankeekåpan och TAD-cylindrarna. Tre maskinkoncept undersöktes: DCT®, NTT? och TAD.