The objective of the thesis is primarily to conform and encode a digital signal to be controlled by software. The idea is to transport today?s tracesignal through the IP-network instead of cable-net. In this report I will suggest a possible solution to get a fully passed result with no peculiar time delay. I will also suggest some ideas for a future work with the new tracesystem..

The main purpose of a Flight Data Recorder (FDR) is to facilitate the investigation of incidents. In order to interpret the data that has been recorded in the FDR the data has to be visualized in some way. This can be done with software on a computer or with hardware that is specific for the model of aircraft that the data originates from.The aim of this project is to visualize data for six parameters from the FDR of Saab 2000 in an avionics rig. The avionics rig resembles the cockpit of Saab 2000 and the displays in it are identical to the ones found in the plane. All six parameters are shown on the same display.Due to safety regulation vital systems in aircraft are doubled, with one system on the left side and one on the right.

This master?s thesis was performed at PartnerTech AB in Åtvidaberg. It addresses the problem of managing test results obtained from testing electronics manufactured by PartnerTech. PartnerTech has developed a test system, called Tor, which performs tests on manufactured boards and stores the test results in files. The Tor system consists of both hardware and software part, where the software runs on an ordinary PC with MS DOS/Windows 2000.

Many workplaces around the world use some kind of presentation software as an aid during presentations. At Westinghouse Fuel Service in Västerås they experienced that they didn´t know how to use this medium to its fullest extent. They wanted to increase awareness of presentation skills with PowerPoint among the employees, to improve their internal and external communication. A desire they are certainly not alone to have in the working life.My research studied how to design guidelines for the use of presentation software, so the users can easily absorb the message and find motivation to use the guidelines. In order to adapt the guidelines to their users, and thus create major opportunities for them to absorb the message, I based my study on the concepts legibility, readability and reading value.

Rapporten innefattar hur en funktionsprototyp till ett vinterhjälpmedel för en rollatorutvecklats. Alla de väsentliga stegen i utformningen beskrivs grundligt, från det att idéerkläcks tills dess att prototypen är klar för tillverkning. Utifrån en idé om ett vinterhjälpmedelhar arbetet fortlöpt till en prototyp bestående av en konstruktion med skidor som enkeltmonteras på rollatorn. Arbetet berör ergonomiska analyser på användande av prototypen samtdimensionering.Stor vikt under utvecklandet har lagts vid människan och hennes funktion för att få en produktanpassad efter rörelseapparatens förmågor och begränsningar.En nyhetsgranskning över produkten har utförts där utfallet var positivt, vilket innebär attprodukten nu är i ett läge där en patentansökan planeras.Produkten lämnar utrymme för vidareutveckling..

Prioritisation of software requirements is a critical part of the development of software. Whichrequirements and in which order they will be developed is one of the main tasks that requirementprioritisation supports.There are different ways that a requirement prioritisation can be used, for example alone or in agroup and with different methods.The purpose of this report is to map out how you can carry out a requirement prioritisation alonewith different types of prioritisation methods and how you solve the problems that can arise whenprioritisting requirements. This is done by documenting the use of three different types of methodsthat can be execute alone. The methods are "100-dollar test", "Ranking" and "Top-tenrequirements".To be able to prioritise requirements, you need to establish which requirements you shall prioritise.The paper retrieves this information by interviewing stakeholders in the system and analysing theresult of the interviews and the execution of the requirement prioritisation.Three problems arose during that work and I present solutions on these problems. The problemswere 1) equivalent requirements when using the "100-dollar test", 2) low differentiation gradebetween the prioritised requirements in the "100-dollar test" and 3) that the requirements that wereprioritised weren't classified before the prioritisation, which leads to inaccuracies in the resultingprioritisation.The solution to the problems that the paper presents is to increase the amount of distributable unitsin the "100-dollar test" to 1000 per requirement, suggestions of classes of the requirements andthe combination of the methods "100-dollar test" and "ranking" to bypass the equivalentrequirements.The report is written in Swedish.Nyckelord: GoTRIS, requirements retrieval, requirements analysis, Viktoria Swedish ICT,requirements prioritisation, requirements, 100-dollar test, ranking, top 10 requirements..

Leisure boats of today have a lot of electronics that needs battery power to work. In additionto that electric propulsion systems have gotten more popular lately, which further increasesthe demand for high battery capacity. The batteries used are mostly lead-acid batteries and toget the most out of the batteries it is important to treat them right. To optimize the electricsystem it is important to have knowledge of how the batteries and the electric motor are usedand which factors affect e.g. efficiency and recharging.A new electric drive that can replace old diesel engines is being developed and needs testingand evaluation.

The purpose with this report is to compare moose browsing in young stands within a small game preservation, and if there are any differences between two areas. The method used in the inventory is a local damage caused by moose browsing survey. It is suitable on areas that have more than 50 hectares but less than 250 hectares of young forest. Inventory of moose browsing is best done on bare ground in the spring and should preferably be done before the flushing begins at the pine. Orsblecks game management area is divided into two different moose management areas, Noppikoski and Siljansringen. During the winter Siljansringen has a denser winter strain of moose, because of the moose seek out lower parts with less snow during the winter. This should also lead to the southernmost part should accommodate larger proportion of damages caused by browsing by moose.

This master thesis has been carried out at Scania R&D at the department for Powertrain Control System Development during the winter of 2010/2011. In the thesis the writer examine and evaluate the existing method for collecting information from the tests carried out during the development of the Powertrain Control Systems software. It also contains suggestions for how a new method that enhance the validation elements could look like.The master thesis uses Vicentes theories of the ecological approach and theories of how knowledge sharing of tacit and technical information works within an organization and between the organization and its customers. First a workplace analysis at Scania R&D is carried out to see how Powertrain Control Systems work and how they test their software. Second a control task analysis, where the aims decided on after the interviews, is compared to the existing method.

In today?s society computers are getting a much more important role. To get a computer to work as intended it has to be programmed. A computer program is written with programming languages. There is an abundance of programming languages available today and there are many differences and similarities between them. The different languages have their advantages and their disadvantages where some of them are intended for fast performance, some to be cheap on memory usage, and some are developed to be easy to program on. In our thesis we have chosen to compare four of todays most common languages, C, C++, Java and Python.

JavaScripts popularity is increasing and the number of libraries too. This report focuses on well-known software metrics in complexity, maintainability and different size-metrics. A few different JavaScript libraries are compared and analyzed. The result shows that there are indeed differences, mostly in size- and complexity-measures where some functions are implemented with a higher complexity..

This thesis aims to develop a control system for measuring electromagnetic compability (EMC). This has meant that a controller designed around an ATmega8 microcontroller has been manufactured and programmed. It has also meant the development of a comprehensive control software in the program MATLAB. The control system has been tested with satisfactory results and can now, monitor and control measurements of the EMC-type..

In this bachelor thesis a complete prototype of an industrial vibration measurement platform has been developed. By measuring a number of variables such as acceleration, temperature and speed conclusions can be drawn on machinery health. The aim is to evaluate hardware and software solutions for a possible future product. Based on a requirement specification a proper hardware design has be developed. The hardware consists of a four-layer PCB with an ARM Cortex-M3 microcontroller and about 250 other components. The PCB was designed, assembled, tested and finally housed in a box.

This study is an evaluation of the runtime watch function in a OEE software, knownas ProTAK. OEE stands for Overall Equipment Effectiveness, it?s a way to measurethe factories process efficiency. The runtimewatch function allows the user to setup and monitor certain critical objects that are of importance for the pulp and paper process at the mill. The data from the runtimewatch can be correlated towards the suppliers specification for the components.

This report is about a thesis that is performed in and for SYSteam Engineering AB in Motala. The thesis work is divided into three parts, study of the market, programming and electronics. The study part consists of examining and comparing different data acquisition systems for testing of different circuit boards, taking into account the modularity, real-time applications, mobility, environmental, interface hardware and software, to be able to define a general module-based data acquisition system in both hardware and software that enables for future developments.The programming part consists of getting started with Visual Studio, which integrates the Measurement Studio for C#. NET. Measurement Studio includes classes and user controls for testing and measuring and offers tools for acquisition, analysis and presentation of real world data.