Food is widely consumed and in 2011 an average American devoured approximately one ton of food. The production of these goods requires large amounts of energy and contributes to 22-31 % of all greenhouse gas emissions occurring in Europe. More than one third of the produced food is discarded instead of consumed, and food waste make up about 30 % of the waste generated by households. 60 % of this food waste could be avoided if the eatables were handled in a better way.Avoidable food waste arises partly because residues from food are not taken care of, and because the food is not stored in a way that optimise its durability. Residues arises part- ly because of the contradictory and complex demands of everyday life and are, because of our busy lifestyle, difficult to avoid.

The real estate company Ihus is facing an expansion of its comfort cooling in Noatun,Uppsala, to provide the buildings in the block with cooling. The buildings in Noatunare mainly used for office premises, where the requirements for an accepted indoorclimate is great. However, it?s uncertain whether Ihus should continue, as currently,producing comfort cooling by themselves using a compressor chiller, or if they shouldconnect themselves to Vattenfall?s district cooling net.The purpose of this report is to examine which technique of cooling is best suited forIhus and their buildings in Noatun. It should also work as a guideline for othercompanies facing the same problem as Ihus.

The purpose with this thesis is to get a compilation of all the critical bolted joints of all enginesproduced at LV Motors. ABB LV Motors produces induction engines with seven shaft heights. Eachengine size exists several variants of components ex. standard shield and flange shield. Depending onwhich components the engine is equipped with arises various types of strains in the engine's parts,certain assembly ways are more favourable than other.The most critical parts in the engine from a mechanical point of view are the screw units betweenshield/stator, feet/stator and bearing cover/shield.

Fukthantering är idag, trots god kunskap inom ämnet, ett stort problem inom byggproduktion då tunga betongstommar ska torkas ut under pressade tidsplaner. Det finns en uppsjö av beräkningsmetoder och hjälpmedel, exempelvis ByggaF och Torka S. Däremot finns inget enkelt sätt att kombinera uttorkning, energiåtgång och kostnader som är användbart i produktionen.Miljön är kanske ett av det här århundradets största samhällsproblem. Lokala brister kan få globala konsekvenser och för att bygga ett hållbart samhälle måste detaljnivån studeras. Byggbranschen är en stor energibrukare där stor vikt på energibesparingar läggs i förvaltningsskedet, medan det försummas i produktionsskedet.

Simulation of different systems can be done using a graphical model description of the system based on block diagrams. The simulation software Matlab/Simulink offers a lot of possibilities to describe a huge number of systems, which can be linear as well as nonlinear. The simulation using Matlab/Simulink is done by integration based on different kinds of numerical methods.When nonlinear Simulink-models are simulated, it is often interesting to apply a Kalman filter to handle the noise that may occur within the process as well as corrupting the measurement. However, application of such a filter leads to an extensive time-consumption despite using fast computers. The reason is that the existing Matlab functions are not constructed for time optimal evaluation.

Abstract Title: The Future of ABC at Sandvik Tooling ? Incorporating ABC with information systems in order to drive business development from a cost point of view. Authors: Jenny Andersson and Camilla Salomonsson. Supervisor: Charlotta Johnsson ? Department of Automatic Control, Lund University.

Miljonprogram is a Swedish building program from 1964 to 1975. During that time about a million homes were constructed. Now, almost 50 years later, they are in desperate need of renovation. In order to fulfil the Swedish environmental objective to decrease energy consumption 50 per cent until 2050, considerable housing stock built under the Miljonprogram has to be renovated.Focus in this thesis is on the building services and theirs profitability that can decrease energy consumption in households build during the Miljonprogram. Building construction is not considered in this report.

This Master thesis is about a postal- and telegraphic building in Eskilstuna, Sweden. The construction methods for the specific building and buildings in general from the same time are described. The purpose of the report is to describe the loads acting on the building and how it has been built and why it has been rebuilt during the years. After this, possibilities of reconstruction and adaptation for today?s demands can be evaluated.

Buildings worldwide account for 40 % of the total energy use. Climate change is of increasing importance, but few are willing to reduce their standard of living or get a higher cost for the change. Energy efficiency of existing buildings gives the greatest benefit economically and environmentally. The real estate company Klövern AB manages 46 properties in Karlstad. Heating is the major cost of the total operating costs of real estate. Rising energy prices increase the need for Klövern AB to improve energy efficiency and to investigate alternative sources of heat.

Time studies in dairy production are an essential tool when deciding about level of mechanisation and automatisation both in investment situation and improving efficiency in existing operations. In previous investigations such studies have been carried out during normal barn conditions during winter. Since there is a compulsory to have dairy cows grazing 3 to 5 months during summer time in Sweden time studies during this season is important to have a full picture of needed working time. During grazing season time studies was carried out at 14 dairy farms representing herd sizes from 66 to 450 dairy cows of which 6 farms with AMS. 8 farms were the same as studied during winter season.

The cost of transportation has strongly increased in the recent years, transportations which are a major part for the construction companies. Skanska Asphalt which is a part of Skanska Sverige AB has noticed that there are significant cost savings to be made with the purchasing of transports. The transports in this case is about asphalt, where the costs are about 10% of the outsourcing business turnover. The purpose of this thesis is to study the working practice that Skanska Asphalt are using today in controlling and time-writing, for the asphalt transportations. Resulting in recommendations on how to improve the working practice at Skanska Asphalt.This study was conducted with the help of a number of interviews with Skanska?s employees and with suppliers of transportation to describe the practices which are being used in during the asphalt transportation.

This thesis analyzes the expected profitability in land based wind power plants. The expected profitability is calculated on the basis of a wind power project in Vartofta, Falköping. The information required to calculate the expected outcome is then concentrated to this project, which is in this thesis called project Näs. In project Näs they plan to build three wind power plants, with each an effect of 2 MWh. These wind power plants are very capital intensive investments with a long and uncertain payback time.

During the past few years a vast amount of research has been done to increase the understanding of the complex ecosystem of the Baltic Sea. Modelling and simulations are important tools to increase knowledge of the system. A suitable model must be simple to use and the parameters and variables needed in the model must be easy to access.In this paper a dynamical mass-balance model, CoastMab, which is validated for smaller coastal areas, has been used to predict concentrations and transports of phosphorus in three large coastal areas - the Gulf of Finland, the Gulf of Gdansk and the Gulf of Riga. CoastMab uses ordinary differential equations to regulate inflow, outflow and internal flows. To reflect seasonal variations in temperature and different types of flows the model has a temporal resolution of a month.

Denna rapport behandlar krafterna och påkänningarna från jorden i en grav beroende av tiden för gravsättning. I rapporten behandlas deformationerna och vad som åstadkommer dem samt hur de kan kompenseras. Rapporten börjar med att gå på djupet med jordens beståndsdelar luft, vatten och jordpartiklar. Dessa har en betydande roll i hur jorden beter sig. Om jorden är nästan vattenmättad före packning kan den anta flytande form och bli svårhanterlig.

In this thesis, the flows of reactive nitrogen (Nr) in Scania were investigated and quantified. The thesis was also intended to form a basis for comparison between the urban nitrogen flow and other flows of nitrogen within Scania. The management of nitrogen in society has disturbed the natural nitrogen cycle. This is linked to a series of environmental problems such as eutrophication, acidification, global warming and smog. The method used was Substance Flow Analysis (SFA) for Nr. For calculation and flow charts Scania was divided into three subsystems; air, water and society.