The report is about efficiency of a current production group where there is no clear production flow and there are some buffers between the operations. The efficiency is done with the help of a tool that is calledWork process of flow production which is used by Atlas Copco CTO. The most obviously results are that the lead time drops from 25 hours to 425 minutes and that the balancing loss decreases from 85 % to 8 %. The report focus on decreasing transports, decreasing buffers, more reliability in lead time and quality. And a more stimulating labour content for the workers is another result..

Today dairy farmers in Sweden are obligated to have lights turned on during night time in addition to the mandatory daylight inlet. This presents a cost for the production but many argue that it can be economically beneficial, especially in loose housing of dairy cows. In loose housing and even more so in herds with automatic milking, well functioning cow traffic during all hours of the day is crucial to optimise production. In order to keep the cow traffic flowing, lights may be an important management tool. It is also perceived among farmers with tied up stall that night light decreases the incidents of cows accidental stepping on their own or neighbours udders.

Increased competition in the IT industry has sparked a need for developing faster innovation processes with more predictable output. One of the biggest issues when it comes to achieving a faster flow through the innovation process lies in managing its high degree of variation. Proposing a solution to this problem, Lean Software Development (LSD), was developed to provide a framework for how IT companies should organize its software development process to achieve increased speed and quality. This study examines to which extent LSD, as a set of values, principles, methods and tools, can be used to improve flow efficiency in the innovation process. A case study of a multinational IT company was made by conducting ten semi-structured interviews with current employees.

AbstractEmbla 5 is an office building which has done a large improvement. The clients of this building has made an order of WSP and the student Anders Kempe to calculate the use of energy for the building, and after that result proposing further measures which can decrease the energy use of Embla 5.The ground for this report is when calculation of the present energy use of the building is stated. To make that information of a number of parameters such as envelope, the heating system and ventilation has been located and set in to the simulation program IDA ICE which calculate the energy use.To improve the energy use further this project has been concentrated to change the system of ventilation. Today the ventilation system is of the kind CAV (constant air volume) and the air flow is dimensioned for after recommendations from BBR and Arbetsmiljöverket in the office spaces. Consider that Embla 5  is an office building where the people only staying for 8-10 hours/day so was the ide to see how much energy saving if the air flow is reduced the time people not being in the building.

The content of the following report is the summarized result of three students thesis at Blekinge Institute of Technology in co-operation with Water Jet Sweden AB. This report will give the reader a description of principles how to measure the abrasive mass flow in a waterjet cutting system. The work began with a visit to Water Jet Sweden AB to get a closer look at the problem. When the analysis of the problem was done the criteria were defined in the form of demands and desires. The main task of the criteria was to guide the search for the solution.

Background: Peripheral arterial disease (PAD), as a consequence of atherosclerosis in the arteria of the limbs, affects one of ten Swedes older than 65. PAD can develop slowly and silently, and involves an increased risk for cardiac infarction and stroke. Measurement of the patient´s ankle blood pressure and calculation of the ankle-brachial index is an evidence-based method to discover PAD. Objective: To investigate how district nurses and general practitioners perceive this method of examination and experience possible obstacles to why it is not more commonly applied at primary health care centres. Method: Data collected by semi-structured interviews have been processed by qualitative content analysis with a manifest onset.

The effects of the deregulation of the electricity market 1996 in Sweden on short-term hydropower regulation are unknown. This report investigates patterns in subdaily regulation in the Ångerman River Basin during the period 1993-2011. Differences in subdaily flows and zero flow events between the periods 1993-1995 and 1996-2011 were studied by analyzing hourly data from 8 regulated and 8 unregulated locations with four subdaily flow variation indices. No correlations between the market deregulation and the regulation intensity in the Ångerman River basin were detected. The number of days natural ranges of variability were exceeded and the magnitude of subdaily variation were significantly higher at regulated locations.

Mathematical models possible to simulate are of great importance in order to make successful projects in the aircraft manufacturing industry. An aircraft fuel system is very complex, containing pipes, tanks, orifices, valves and pumps. The principal of this thesis is using the tool Easy5, which no longer is considered reliable enough in terms of development and support. This thesis tries to evaluate the Modelica language as a possible alternative to Easy5. To make this evaluation, the components concerned in the fuel library in Easy5 are implemented to the Modelica language.

The report is about efficiency of a current production group where there is no clear production flow and there are some buffers between the operations. The efficiency is done with the help of a tool that is calledWork process of flow production which is used by Atlas Copco CTO. The most obviously results are that the lead time drops from 25 hours to 425 minutes and that the balancing loss decreases from 85 % to 8 %. The report focus on decreasing transports, decreasing buffers, more reliability in lead time and quality. And a more stimulating labour content for the workers is another result..

The content of the following report is the summarized result of three students thesis at Blekinge Institute of Technology in co-operation with Water Jet Sweden AB. This report will give the reader a description of principles how to measure the abrasive mass flow in a waterjet cutting system. The work began with a visit to Water Jet Sweden AB to get a closer look at the problem. When the analysis of the problem was done the criteria were defined in the form of demands and desires. The main task of the criteria was to guide the search for the solution. The work proceeded with an extensive search for abrasive flow meters along with obtaining information about flow measurement in general. When the search for abrasive flow meters resulted in nothing all the efforts were concentrated on finding a principle of measurement that could cope with the criteria.

This examination work is performed at the institution of industrial economy and production at Jonkoping technical university, for JELD-WEN Door Solutions plant in Forserum.Today the focus in the company is on to reduce their inventories binding of capitals as well as inventory of products and that includes to get a good control of the supply and handling of material which is of great importance.JELD-WEN Door Solutions is one of the worlds leading producers of windows and doors and the head-office is located in Oregon, USA.A great number of wooden doors are manufactured by the company in varying of constructions, classifications and performance.The production of the plant in Forserum has a project- and customer focus manufacturing where only internal doors are produced. The overall market they are concentrated on is to different institution such as schools, hospitals etc.The purpose of this work is to investigate possibilities to improvement of material- and production control at JELD-WEN. The report will handle the master production schedule to and from the production divisions within manufacturing industry. Focus will be on the way for information- and material flows from arrival, transport within the company and further on to customers.Further a map of the flow was performed which gave a clearer picture of the connection between the flow of information- and material for the manufacturing process. On the basis of the mapping of the flow, the group discovered that the flow of material had some improvement potential.

Flooding events are no longer rare, floods occur all over the world. Accordingly, it is vital for the society and different authorities to work with flood mapping. To meet the goal of Uppsala kommun to map the risks of floods in Uppsala län, a map of the different areas around Funboån which are inside the area of risk for flooding have been developed.In the work, cross sections and the water flow have been measured. Moreover, an echo-sounding have been carried out in Funboån to map the bottom topography. From the bottom map and laser scanned data covering the study area, a terrain model was created.

The aim of the present study was to evaluate the effects of large amounts of straw in the farrowing pen on thermal regulation of the newborn piglet in different weight classes. 20 sows were given 15 kg of straw in the farrowing pen 2 days prior to until 7 days after parturition. A control group of 18 sows had no straw in the pen. 6 litters from each treatment were observed. Measurements of piglet body temperature were made at 0h, 2h, 4h, 8h and 24h after parturition. At ?8h? the body temperature of the piglets in the Straw group were significantly higher (P=0,0149) than the piglets in the Control group.

Background: Diabetes mellitus is a chronic disease that manifests as an increased level of glucose in the blood. According to the World Health Organization (WHO), 347 million people have diabetes worldwide. In year 2004, 3.4 million people died from the consequences of high blood glucose. In the Swedish population the prevalence of diabetes is estimated to 3-4 %, out of which 85-90% are Type 2. Among senior citizens a prevalence of diabetes is seen in Sweden up to 14 - 15%.

The dissertation were performed on SP, Technical Institute of Sweden. The dissertation were carried out on the measurement technical department, this dissertation is a part of a bigger project, project ClampCal. One of SP?s returning assignments are flow-measurement. When flow-measurement is performed, the flow has to be stopped so that a meter can be installed in the pipes where measurement is going to take place. At every stop there is time delay in the flow which causes the customers to loose money. This is why SP wanted to find a better solution so that measurement can be done without any stops in the flow. Usage of a so-called Clamp-on meter was considered, but since the measurement uncertainty is too large it takes some investigation on the parts where the largest uncertainties occur and thus find a solution that can diminish the uncertainty as much as possible. The parts that were considered to have an opportunity to reduce measurement uncertainties were the fluid temperature, its characteristics and the pipe geometry and its characteristics. For the fluid temperature a Pt100-sensor with four different radii for various pipes was used.