Drinking water is produced from raw water and is either from groundwater or surface water. This thesis aims to find out if the cleaning process of raw water is sufficiently effective. This is important because consumers are otherwise at risk of waterborne infection caused by pathogens. There are three groups of pathogens; bacteria, virus and parasite. These have different characteristics which mean that they require different water treatment to be separated.

Drinking water is produced from raw water and is either from groundwater or surface water. This thesis aims to find out if the cleaning process of raw water is sufficiently effective. This is important because consumers are otherwise at risk of waterborne infection caused by pathogens. There are three groups of pathogens; bacteria, virus and parasite. These have different characteristics which mean that they require different water treatment to be separated.

This thesis has been carried out in cooperation with Burseryds Bruk AB.Burseryds Bruk is a company that manufactures steel strapping. The thesis isabout developing a concept of protection that should be used to protect theoperators from the rotating parts of the machinery lines. The aim of the projectwas to improve work safety for operators working at the machines by producing aconcept for a protective device. The project's first part was based on ergonomic data collection methods tounderstand the operations performed on the machine and the hazard occurringduring the process. The methods used to collect data were, interviews,observations and questionnaires with the operators of the company. This was thenused to make the ergonomic analyzes hierarchical task analysis and link analysis. The data collected from the company's operators was used create 10 conceptswhich were then evaluated.

In this Master's thesis, a direct-conversion receiver front-end has been designed in a 0.18um CMOS technology. Direct-conversion receivers (DCR) have obvious advantages over the heterodyne counterpart. Since the intermediate frequency (IF) is zero, the problem of image is circumvented. As a result, no front-end image reject filter is required and the channel selection requires only a low-pass filter, which makes it easy to integrate directly on chip. However, the DCR also suffers from several drawbacks such as extreme sensitivity to DC offsets, 1/f noise, local oscillator (LO) leakage/radiation, front-end nonlinearity and I/Q mismatch.

In this Master thesis, microwave connections between circuit boards are constructed. The primary frequency band is the X-band (8-12 GHz). The purpose of the connections is to enable a more simple and cheaper way of mounting the circuit boards inside a container. The connections have been designed and evaluated, using different computer programs. A few prototypes have been built and measured.

Drinking water is produced from raw water and is either from groundwater or surface water. This thesis aims to find out if the cleaning process of raw water is sufficiently effective. This is important because consumers are otherwise at risk of waterborne infection caused by pathogens. There are three groups of pathogens; bacteria, virus and parasite. These have different characteristics which mean that they require different water treatment to be separated.

This report describes a Bachelor thesis work in which a robotised laser welding cell has been modelled and simulated for the purpose of making a presentation movie. The report shows that the work has been concentrated on making the movie from the modelling phase through the recording of the movie and ending up with the editing of the final presentation movie. A pre-study was made prior the Bachelor thesis work. In the pre-study a literature study was conducted about measurement and calibration of a welding cell. Measurement of almost all equipment in the entire cell was also conducted in the pre-study.

The storm Gudrun in 2005 led to massive windthow damage in forests in southern Sweden. Since then there has been a growing interest in factors influencing wind damage in above all Norway spruce (Picea Abies) stands. Although many other interesting areas still need to be examined. In 2005 there where a lot of stands that suffered different degrees of damage, a lot of these stands weren?t cut, but instead left to grow. The future development of these stands is uncertain and the guidelines are unclear.

Drinking water is produced from raw water and is either from groundwater or surface water. This thesis aims to find out if the cleaning process of raw water is sufficiently effective. This is important because consumers are otherwise at risk of waterborne infection caused by pathogens. There are three groups of pathogens; bacteria, virus and parasite. These have different characteristics which mean that they require different water treatment to be separated.

Since energy simulations are used to verify that projected residential buildings will reach the current energy requirements it is important that the results are reliable.This report investigates the extent of uncertainty in energy simulations, estimates the causes of the uncertainty and its economic and environmental consequences.The method used in this report is based on three validation methods; empirical validation, analytical validation and comparative validation. The analysis was carried out for five multi-family dwellings in Uppsala with installed meters for energy measurements. One of these objects, Klockarlunden, was studied in more detail than the others.The results show that the deviations are between 10 and 29% for the studied objects, which means that the uncertainty is estimated to be at least 29%. All simulations underestimate the buildings need of energy. The simulation for Klockarlunden can predict the energy consumption to be within the range of 46-98 kWh/m2year with 90% confidence level based on the current uncertainty.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

At Forsmarks Kraftgrupp AB (FKA) forces on pipe systems due to transient flow are frequently calculated as a step to verify their structural integrity. In nuclear industries these forces are often calculated with a one dimensional thermal-hydraulic analysis-code called RELAP5. When calculations regarding more complex geometries are needed, the three dimensional code Fluent is often used. This code is highly time consuming and requires large computational power.This projects aim is to compare calculations of pressure, flow and forces carried out by RELAP5 and Fluent for an arbitrary pipe section during transient flow conditions. This has been accomplished by constructing a simple geometry for which a transient flow is simulated in both programs.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.