The objective of this thesis is to examine the difference in workability in fresh concrete, when crushed fine aggregate replaces natural gravel. The shape of the fine aggregate,  packing and flow of six crushed material and three natural materials will be determined by easy studies, the results will be compared with a slump cone test..

This report describes the building of a computer model that makes it possible to simulate the thermal climate in a greenhouse. The computer model is built on the physical theory of heat exchange that occur in a greenhouse, such as radiation and convective heat exchange. The model also includes the heat storage that is active in a greenhouse.The computer model is used to simulate the thermal climate in a greenhouse under three periods, winter, spring and summer. It also investigates which effect a concrete wall has on the thermal climate in a greenhouse. The purpose of putting a concrete wall in the greenhouse model is to investigate the possibility to store heat during the day and then use this heat when the temperature drops during the night.The result from the simulations shows that a concrete wall levels the big difference in temperature that normally occurs under a day in a greenhouse.

Cement manufacture accounts for 3-5 percent of total global carbon emissions. There is a growing interest in reducing the environmental impact and conserve limited natural resources. In cement production, clinker productions consume 87.5 percent of the total energy consumed in the cement manufacture.Cementa has since many years, focused on reducing the environmental impact of cement production. The work has involved the entire production process from selection of alternative fuels to the development of cement with less clinker content. During 2013/2014, two new types of cement (Bascement and CEM II / B) will be introduced to the Swedish market.

This thesis has examined the Tekla Structures modeling software and answered the question of whether it could act as a suitable modeling program for the design department at Bjerking AB in Uppsala. The method used in this work is a case study of a previous project with existing basis to work form. The demarcation of the study was to examine only the usability of the foundations of in situ concrete. The work examined three main areas within the design process. The first was to model the concrete elements then to model the reinforcing and ultimately production of the drawings. Because Autodesk Revit was the existing modeling program in the Department conducted the evaluation as a comparison between the two programs.

This report will try to evaluate the use of rented concrete casting moulds, which are used to build walls and system of joists. The evaluation is only examining the economical aspects.The cost of using concrete casting moulds is a big part of the total production expenses. Therefore it is important that the calculated price not exceeds the final costs of the casting moulds. The calculated price is the price used in the process of making an offer.The evaluation consists of a comparison of the calculated price and the final costs for three building projects. It also evaluates the exploitation of the concrete casting moulds for each project.The report is made by Sven Gynne and Anders Alexandersson at School of Engineering, Jonkoping University, in cooperation with PEAB Jonkoping.

AbstractToday there is an opportunity to reinforce concrete with steel fiber reinforcement. In some cases, completely replace the conventional reinforcement. Replacing conventional mesh reinforcement with steel fiber reinforcement in slabs on ground has shown economic benefits, less crack width and less reinforcement amount.Today there are no Swedish standard for designing steel fiber reinforced concrete, what is there is different international recommendations.In this work, design methods for steel fiber concrete are used according to RILEM and Bekaer Swedish AB's software DRAPRO. For other design methods Eurokod 2 is followed.In this work, the design of slabs on ground that are not exposed by large tension strength been designed. Design of crack-reinforcement and restrictions of crack width have been conducted in three different slabs on ground.The calculations have been performed using only conventional reinforcement and only steel fiber reinforcement, and the results are then compared.The results of the theoretical analysis are summarized in tables that compare the amount of reinforcement, crack width and economic cost.This work showed that the slabs on the ground reinforced with steel fibers provide less crack width with a minor amount of reinforcement.

The incidence of damage to the claws and legs in piglets caused by the floor in farrowing pens is a widely known problem and very common in today's pig herds. Although the association between floor and damage has been known for over 35 years, no suitable solution has been found to reduce the negative impact. The purpose of this study was to make a literature study to document the experiences of the use of different types of flooring in farrowing pens and also, in an own study, examine if soft floor in farrowing crates could lead to reduced damage to the claws and legs in piglets compared to concrete floor. The study was conducted in two herds, A and B. In each herd, farrowing pens with concrete floor and concrete floor with polyurethane coating were compared.

AbstractThis report intends through a case study to investigate if lightweight concrete isappropriate as main material in the outer wall of a seven storey residential building.A technical design is carried out in accordance with the definitions and requirementsfor passive houses, given by FEBY?s1 ?Demand specification for passive houses?.A literature review is also carried out for a comparison between regular bolt wall andlight weight concrete wall, with a focus on the safety of moisture.The lightweight concrete block used in the report is as a celblock produced by thecompany H+H Sweden AB.The methods used have resulted in compliance with requirements andrecommendations from authorities. Calculations of energy, noise and moisture riskassessment has been carried out.The work has resulted in the conclusion that the lightweight concrete itself is notable to isolate in the extent necessary to obtain chosen U-value of 0,1 W/m2 ° C,without getting to thick. Therefore additional insulation is needed. There are fewrelevant reference objects built with only light weight concrete.

Konventionell betong måste vibreras för att den skall fylla ut formen och omsluta armeringen, men även för att en homogen betong utan stora luftinneslutningar skall erhållas. Vibreringsmomentet är ett mycket tungt arbetsmoment som sliter hårt på främst rygg, axlar och nacke. Vibreringen ger även upphov till s k vita fingrar vilket orsakas av en försämrad blodcirkulation till följd av att vibrationer från vibratorstavarna fortplantar sig upp i händerna. På mitten av 80-talet började en vibreringsfri betong att utvecklas i Japan och till Sverige kom den för några år sedan. Den vibreringsfria betongen skall, utan vibrering, fylla ut formen och omsluta armeringen.

AbstractThis report intends through a case study to investigate if lightweight concrete isappropriate as main material in the outer wall of a seven storey residential building.A technical design is carried out in accordance with the definitions and requirementsfor passive houses, given by FEBY?s1 ?Demand specification for passive houses?.A literature review is also carried out for a comparison between regular bolt wall andlight weight concrete wall, with a focus on the safety of moisture.The lightweight concrete block used in the report is as a celblock produced by thecompany H+H Sweden AB.The methods used have resulted in compliance with requirements andrecommendations from authorities. Calculations of energy, noise and moisture riskassessment has been carried out.The work has resulted in the conclusion that the lightweight concrete itself is notable to isolate in the extent necessary to obtain chosen U-value of 0,1 W/m2 ° C,without getting to thick. Therefore additional insulation is needed. There are fewrelevant reference objects built with only light weight concrete.

Floor surface in pig facilities can have an impact on animal welfare and pig health, as it can cause the pig physical damage and thereby increased risk of infectious diseases and lameness. The development of pig housing systems has resulted in a decreased use of bedding. It seems hard to find the optimal floor in farrowing pens, as it must suit both the sow and piglets. The floor friction needs to be adequate to avoid slips and at the same time should the floor be non-abrasive. Abrasions and lesions caused by the floor are not only causing the animal suffering, but are also negative from an economical aspect.

At the beginning of 2011, Sweden started using the European rules for structural design, the Eurocodes, instead of the previous national rules. In both the previous rules and the Eurocodes, it is possible to dimension concrete columns using tabled values. However, the required cross section measurements have increased considerably. Moreover, it is possible to dimension concrete columns using calculations, however, this is unusual.The development of a fire in a fire cell can be divided into the growth stage, the fully developed fire and the cooling phase. The duration of each phase, as well as the temperature, is dependent on a number of factors, e.g.

A trend in modern landscape architecture is to design pedestrian streets so that vehicles and people move in the same area. By doing this, traffic tends to slow down. On the market though, there is a lack of furniture that corresponds to the requirements of these kinds of public places. Therefore, I have designed this furniture, called VOX, which is planned to be used on streets, schoolyards and squares. One objective has been to promote the product to the industry.To achieve this, I have been in contact with people from different professions, which have all influenced my designprocess.

Användandet av betong som ersättare för stål vid produktionen av vindkraftverkstorn har ökat den senaste tiden. Betongtorn är betydligt billigare än ståltorn men problem som sprickbildningar, frostsprängningar och följaktligen armeringskorrosion har uppstått bl a på grund av vibrationer från rotorn. I fundamentet i vindkraftverk kan ovan nämnda problem också uppstå och det uppfyller således inte alltid funktionskraven. Det här examensarbetet undersöker möjligheten att eliminera dessa problem genom att använda en sorts högpresterande betong kallad UHPC 2.2 med syntetfiberarmeringen, STRUX. Jämförelser mellan tidigare empiri om högpresterande betong och laborativa tester på UHPC 2.2 visar att den senare är beständigare och ger möjligheter till en större sprickfrihet.

This Master thesis is about a postal- and telegraphic building in Eskilstuna, Sweden. The construction methods for the specific building and buildings in general from the same time are described. The purpose of the report is to describe the loads acting on the building and how it has been built and why it has been rebuilt during the years. After this, possibilities of reconstruction and adaptation for today?s demands can be evaluated.