This master thesis was a continuation of a previous study in the diesel exhaust characterization, which is part of the academical work embedded in the EMIR-1 project. The main objective of this thesis work was to finish the installation and make the proper modifications of the particulate mass measuring system located in one of the engine test cells at KTH, in order to be able to measure the mass of the particles from the exhaust of diesel engines.This experiment requires a diluted flow sample from the exhaust that should be sent to the device that makes possible the measurement of particle mass, called TEOM. In the first stage of this project, the objective was to study and make the proper modifications in the existing KTH diluter because there were several problems to obtain a constant dilution ratio from it during tests.This modifications were made and it resulted in a great improvement in the maximum inlet and outlet flow that this diluter can handle. Therefore another modification is proposed for controlling the inlet exhaust flow so it will be possible to regulate the dilution ratio and make it constant along a wide range of engine loads and speeds.The second and most important stage was to make particulate mass measurements possible by analyzing the frequency signal from the TEOM device. The idea was to obtain the frequency of oscillation from the tapered element in the TEOM, and therefore with the proper correlations, be able to predict the particulate mass concentration in the exhaust flow from the engine.An electrical problem in the TEOM circuit was detected and corrected, so the signal that carries the frequency from the TEOM can be analyzed properly.

The government regulations for energy use in buildings will be tightened in the future. At the same time the interest in environmental classifications and certifications of buildings is increasing. This has meant a new situation for solar energy. The designs of solar heating systems are often based on experience and/or rules of thumb, rather than calculations and simulations. This thesis examines whether simulation tools, in this case Polysun, are useful in this work.

This study was conducted at VikingGenetics' bull breeding station in Falkenberg, Sweden. The bulls waiting for the results of their progeny testing at this station are either kept in group housing or individual housing. Since both of these housing systems have advantages and disadvantages, it was in the interest of VikingGenetics to know which of these housing systems is the best. The aim of this study was to investigate the welfare of the bulls in these two housing systems through behavioural observations and the use of activity monitors. In the preparations for the study 16 bulls, 8 in each housing system, were chosen.

Detta examensarbete har utförts hos Vattenfall Eldistribution på avdelningen Kontroll och Skydd med målsättningen att utforma och utvärdera en nätmodell avsedd för jordslutningssimuleringar i PSCAD. Ombyggnationen från luftledningar till markkablar har medfört att kapacitansen i distributionsnätet ökat, vilket ställer högre krav på jordfelsutrustning och på nätanalyser för att kunna försäkra att en säkerställd frånkoppling kan ske enligt de myndighetskrav som föreligger. Syftet med arbetet har varit att undersöka hur en nätmodell bör utformas för analys av stationära in-svängningsförlopp och utvärdera hur stor noggrannhet som kan förväntas gentemot verkliga jordfelsprov vid felresistanser på främst 3 k? och 5 k?. Nätmodellen har ut-formats efter ett verkligt impedansjordat mellanspänningsnät med ?-länkar i PSCAD och utifrån de nätuppgifter som förekommer i Vattenfalls näthanteringsprogram Netbas.

Today more effective computer programs are in use, regarding design of geotechnicalconstructions. There is a risk that the theoretical background of the computerprograms, its limitations and the signification of the choice of soil parameter isforgotten when the computer programs become more user-friendly.This Master thesis deals with simulation and analysis regarding three computerprograms, FEM-design, with the addition Raft, Plaxis and BE-slab. Comparisons aremade for settlement and maximum moment in a concrete-plate. FEM-design is a threedimensional FEM-program, foremost created for design engineers. Plaxis is a twodimensional FEM-program, intended for geotechnical engineers while BE-Slab is aBoundary elements program in two dimensions that is mainly used by designengineers.

Ammerån which is a small forest river in eastern Jämtland is a well-known river that has been a popular fishing river for a long time. The actual Ammerån begins downstream the lake Solbergsvattnet at Hammerdal and flows into the Indalsälven 10 km upstream Hammarstrand. The river environment switches between forests with wilderness feeling and open agricultural land. The entire Ammerån is today a nature reserve and protected from hydropower development. Fishing in Ammerån has mainly been focused on trout and grayling, and is so even today.

The red-tailed monkey (Cercopithecus ascanius) is a small, alert and active animal inhabiting forests with dense vegetation and as such hard to observe in its natural habitat. The principal aim of this study was to scrutinize whether the methods, previously used in a behavioural study of the blue monkey (Cercopithecus mitis) can be applied in studies of the red-tailed monkey?s behaviour as well. Additionally, habitat preference and foraging behaviour of the red-tailed monkey were examined. The study was carried out between the 16th and the 22nd of March 2009 in the Sabaringo forest, located on the western border of the Masai Mara National Reserve.

This thesis concerns how the power quality in the grid is affected by the connection of wind power plants. As things are at present, Fortum Distribution AB has a number of wind turbines and wind parks connected to the own grid. As the pressure on building and connecting additional wind power is increasing, so is also the interest of how the already existing wind power generation affects the power quality in the nearby distribution grids. The study is performed by direction of Fortum Distribution AB and is limited to the 10 kV/40 kV-grid in Bohuslän, Sweden. The methods for calculation of power quality are compared to the results of a number of measurements.

Lake Bornsjön is situated 30 km southwest of Stockholm in a rift valley lake and consist three basins outstretched in northwest-southeast direction. The surface area is 6,7 km2 with a maximum depth of 18,3 meters, a mean depth of 9,8 meters and a retention time of the water of 6,5 years. The drainage area is 42 km2 and consists mainly of arable land (ca 1000 ha) and productive forestry land (2500 ha), but in the drainage area there are also restored and fairly newly constructed wetlands.Today the Stockholm area receives its drinking water from Lake Mälaren, but if there would be any pollution of this source, Lake Bornsjön would act as the water source. The area surrounding the lake was bought already in 1899 by Stockholm Stad for protection of the lake and was taken over 1993 by Stockholm Vatten AB. It has been a water protection area from 1988 and it was also accepted as a nature reserve in 1995.

Avloppsreningsverk står inför uppgiften att rena inkommande vatten för att möta lagstiftade gränsvärden till en så låg kostnad som möjligt. Att syresätta biologiska reningsprocesser är kostsamt eftersom luftningsanordningen förbrukar mycket energi. Ungefär en femtedel av Himmerfjärdsverkets totala elenergiförbrukning går till luftning av biologiska processer.För att öka Himmerfjärdsverkets energieffektivitet startades under 2010 experiment med olika strategier för luftflödesstyrning. En av verkets nitrifikationsbassänger byggdes då om för att möjliggöra zonvis reglering av syrehalten.Syftet med denna studie var att utvärdera reglering med ammoniumåterkoppling och syrehaltsprofil för styrning av Himmerfjärdsverkets nitrifikationsprocess. Utvärderingen baserades på reningsresultat och energiförbrukning.Med nuvarande reglerstrategi varieras luftningen genom återkoppling från syrehalten i den andra av sex zoner i varje luftad bassäng.

Historically transformers with system earth equipment have been modeled as open circuits in zero sequence. This approximation has been satisfying, but lately it has been discovered that equipment on one side of the transformer have responded to faults that occurred at the other side. Most of these problems took place when the majority of the system on the secondary side of the transformer contained cables. These findings have led to questioning whether or not the former model of the transformer in zero sequence is correct. This report investigates if it is necessary to represent the transformer in zero sequence in another way than it is usually done today.

When planning new wind farms, the cost for the internal electrical grid is estimated to account for 8-9 % of the total investment cost. On top of that, the cost for accumulated reduced income over several years (due to electrical losses), has to be added. The economic lifespan is relatively long (about 20 years) which means that an error in the loss calculation could lead to a bad decision basis. The accumulated reduced incomes due to electrical losses can be higher than the initial investment cost for the internal electrical grid.Today, Statkraft Sweden is using a template number when estimating the electrical losses in a wind farm. The actual losses are probably lower than the template number which could lead to an unnecessary high loss cost when planning a new wind farm.The aim of this M.Sc.

This thesis analyzes the expected profitability in land based wind power plants. The expected profitability is calculated on the basis of a wind power project in Vartofta, Falköping. The information required to calculate the expected outcome is then concentrated to this project, which is in this thesis called project Näs. In project Näs they plan to build three wind power plants, with each an effect of 2 MWh. These wind power plants are very capital intensive investments with a long and uncertain payback time.

Föroreningar av metaller är ett problem längs med kusterna, vilket har en negativ inverkan på vattenlevande organismer och miljön. Orsaken till detta beror till stor del på pågående utsläpp från tätorter, hamnar, industrier och på ?gamla synder (då det inte fanns några detaljerade miljölagar som reglerade spridningen av föroreningar från exempelvis industriprocesser)?. Utsläpp av föroreningar behöver inte bara komma lokalt utan kan också transporteras via avrinningsområdena och via atmosfäriskt nedfall. Idag arbetar länsstyrelsen med att invertera och sanera förorenade områden, men för att kunna ta reda på hur det ligger till med kusterna och hamnarna är sedimentprovtagningar ett måste.

I en tid med allt mer påtagliga miljöhot, ökande CO2-utsläpp och stigande efterfrågan på el är det viktigt att utvecklingen av billig och effektiv förnyelsebar energi fortsätter runt om i världen för att kunna konkurrera mot billigare, icke förnyelsebara, energikällor. Ett steg i detta är att utveckla och effektivisera solkraft till den nivån att länder och företag väljer att investera i solkraft. Mer konkret kan det ske igenom utveckling av nya, mer effektiva, solcellsmoduler.I denna studie ska en ny typ av solcellsmodul, SmartPlus ? utvecklat av Innotech Solar, jämföras mot deras standardmodul EcoPlus för att undersöka om den nya modulen kan bidra till högre andel solkraftsgenererad el i Sverige och där med minska CO2-utsläppen. Den nya solcellsmodulen är framtagen för att bättre kunna hantera och ta tillvara på solinstrålningen om en del av modulen utsätts för skugga, därför kommer studien simulera de båda moduler i en solpark där det sker intern skuggning mellan modulraderna.