The aim of this study was to investigate how individuals perceive the process of sexual/romantic attraction. A phenomenological approach was used, where the participants were asked to reflect as freely as possible upon a question formulated by the authors. 13 persons were selected through purposive sampling, eight men and five women, all between 20 and 30 years old were interviewed but only 8 were analyzed through phenomenological based software MCA-Minerva. The results showed that all participants talked about three steps; eye contact, closing the distance and conversation. In the latter step they differed regarding actions taken to attract.

An energy study has been performed on two blocks in an area called Gävle Strand. The buildings are owned by a tenant-owner?s association called brf Carolina and were built by the company Skanska 2008. The builder as well as brf Carolina are pussled by the fact that electricity use is higher than expected while heating is less. Skanska is also very interested in finding out how much heat recovery from stale exhaust air through a geo-thermal heat pump is contributing to the general heating requirement and energy balance in four out of the ten buildings located on the properties.To find possible answers to the higher electricity use a literature survey on user behaviour was conducted.

To be able to measure high-surge voltages and transients with short rise times youneed measuring instruments with a high sampling frequency and large Bandwidth.These surges and transients occur primarily at lightning but can also occur at forexample at connecting errors at an electrical switch-gear. This report describes thework with finding two solutions for measuring and log data from these surges andtransients. One temporary solution where a measurement program has beendeveloped. A second solution where different company solutions have been analyzedto decide which fits best. For these measurement solutions two solutions for bringingdown the voltage has been used.

There is a great need to reduce nutrient leaching from arable land into lakes and oceans. By using several different types of models it has previously been possible to describe nutrient losses in a catchment area with a minimum unit of sub-catchment level. At present, it is instead desirable to model a smaller catchment with an opportunity to re-connect the results to the corresponding fields in the catchment. Such models already exist but they are not fully able to properly describe Swedish conditions and land characteristics in our region.With the approach of creating such a model, SLU has developed a project with this work as its first stage. The model is expected to be created under the working name SWE-model which stands for Soil Water Environment and is in this first stage supposed to apply the SOIL model in catchment scale. During the procedure to describe the first step in the process of developing such a model adapted to Swedish conditions and which works in the catchment scale with an area of about 10-30 km2, focus has been set on calculating the transport of water flow from different hydrological response units. Regardless of the processes occurring in the soil after the water has been added, it is assumed that all the water which flows from each simulated unit is drained.In the first step the hydrologic response units were identified based on land use and soil type in the study area. With the help of a script with functions that retrieve and transform data, certain units were chosen for simulation. The script was also created in this project. Finally, the model results were aggregated and summarized for each unique unit, for each sub-catchment, and also for the whole catchment.From the results it is possible to see similarities in the flow dynamics between modeled and measured data. The efficiency coefficient has been calculated to correspond to the mean of the measured values for the whole simulation period. With an automated calibration process the model should be able to perform better. The volume error gives an indication of overestimation from the model..

This is a study about the Swedish liming operation and the Swedish liming officer?s opinions of some aspects regarding ecology, economy and organization. The study objectives was motivated due to the recent changes in manuals for the assessment of limed waters and the suggested changes in decision making and decreased budget for liming. Moreover the anthropogenic acidification effects on the ecology are in many ways complex. Furthermore it was made in order to gain knowledge about the liming officer?s opinions in order to improve the ability to meet their needs regarding the assessment tools and also to investigate if other things can be improved concerning the liming operation.

The borehole heat exchangers of today suffer from poor thermal and hydrodynamic performance. The purpose of this thesis is to improve the performance of ground source heat pump systems and thermal energy storages by increasing the energy efficiency of the borehole heat exchangers. For this reason, the annular coaxial borehole heat exchanger (CBHE) has been analyzed. This type of heat exchanger is interesting in terms of both thermal and hydrodynamic performance. A model has been set up in the program Comsol Multiphysics in order to investigate the heat transfer characteristics along the borehole.

The pathogenic fungus Rhizoctonia solani causes major economic losses for potato producers in Sweden. The producers, as well as advisors, have reported possible increases in severity of R. solani when free-living plant parasitic nematodes are present and active. There are several examples in the literature of interactions between pathogens where one, or both species, support or increase the damage made by the other organism. These complexes are important to investigate and to be able to forecast, since even low incidences of fungi or nematodes may result in an interaction of significance.

Severe floods caused by heavy autumn rains in year 2000 raised the question whether measures to reduce the damage from high water levels, in the area surrounding lake Glafsfjorden and along the river Byälven down to lake Vänern, are possible. One option is to reduce flow resistance along the river and thereby lower the maximum water level a given inflow would cause. Good knowledge of hydraulic and hydrological conditions is necessary in order to estimate the effect of such flow-reducing measures. In order to quantify such effect a 1-dimensional hydraulic flow model has been set up for the river Byälven using the software package MIKE 11. The model is more detailed, especially concerning topography and bathymetry, than earlier models used for studies of the river.

In this work, a method was developed and evaluated for calculating the life of welds under the influence of fatigue loads from a vibration environment. Typically, a shaker table is used for testing a component against vibration loads. The shaker table creates a vibration environment that is defined in the frequency domain by a power spectrum.Similarly, a virtual vibration table can be used to calculate the same type of load environment, which can then be used to calculate the expected lifetime. The benefit of this method is that it can be used in design, as well as in simulation of tests before physical verification tests are carried out.Today there are methods for calculating fatigue life of non-welded base material, but since many components contain welded joints, there is a need to apply this method to those types as well. To achieve this, the thesis combines two different areas, which together provide a method for fatigue assessment of welds using a virtual shaker table.The methodology is carried out by modeling the component, and its welded joints, in a finite element program.

In this report I will describe how an art-directed fluid effect for motion picture can be achieved. This effect will be an explosion with a visual style that is congruent with Pixar's movie Up. To begin with I will analyze the visual components that are used in Up and control the fluid simulation to get the desired visual style. I will briefly explain the background of my thesis, why it is interesting to create designed effects and why it is hard to design fluid effects. In the method I will explain my work process and some of the challenges that arises.

The aim of this study was to investigate the social behaviour and time budget of breedingbulls kept at VikingGenetics, Falkenberg in Sweden when the staff was off duty. It was ofinterest to see if there was any difference between bulls housed in group pens and bullshoused in individual pens. It was also of interest to investigate if there was any differencein the behaviour between the dairy breeds Swedish Red (SR) and Swedish Holstein (SH).Sixteen bulls were used in this study. Eight bulls kept in individual pens and eight bullskept in group pens were used. The individually housed bulls had a social gate with widerbars where the bulls could but their head and neck through to have social contact with thebulls in its neighbouring pens.

This report covers the conceptual design of a new one person hybrid vehicle that is to be fast and convenient to drive on the roads. The vehicle is most of all supposed to be used as a commute vehicle but can also be used at other occasions as well.During the work with this project the group has focused on three larger areas, the outer design (body), wheel chassis and an ergonomically designed interior. The group was not able to just create these parts in 3D to get a trustworthy vehicle, hence number of other components and details were also created to get a better entirety.The outer design starts with idea generation and sketches and ends with a 3D model which is rendered to show how the final product is going to look. The design of the body has been going on during the entire work process due to new ideas and improvements that seemed interesting and had to be changed.The wheel chassis also started with idea generation, research and sketches. It ended up with a simulated 3D model which later on was mounted on the vehicle body to show how the vehicle is going to perform during usage.

In this master?s thesis real settlements for the over consolidated clay below Arenahallen in Halmstad are compared with two different models for settlement calculations; Chalmersmodellen without creep and Chalmersmodellen with creep. Chalmersmodellen with creep is based on Terzaghi?s consolidation theory with an addition to creep. The purpose has been to find out whether Chalmersmodellen with creep can be used for this clay or if Chalmersmodellen without creep should be used instead.

I detta projekt undersöker vi om man kan bygga en maskinaktivitetssensor medhjälp av en enkretsdator som genom en accelerometer mäter en maskinsvibrationer. Sensorn skall generera en statussignal. Accelerometern ger enmätbar signal baserad på maskinens vibrationer. Enkretsdatorn används för attsampla, transformera och analysera signalen och generera statusinformation.Med LabView kan vi spara, studera och analysera olika signaler och olikatransformer. Vi studerar maskinvibrationer i LabView och beslutar att 5 kHzsampling räcker för att fånga intressanta vibrationer.

The interest for power and energy measurement has greatly raised with todays increasing electricity prices and enviromental awareness. In the search for energy efficient solutions, the measurements are more complex due to increasing of non linear components. Harmonics and non sinusoidal voltages put high demands on sampling and filtering. Meanwhile, the price must be controlled so the customer still will find it interesting to invest in smaller plants. ITT W&WW asks for a robust, heat resistant power meter with compact dimensions to allow mounting inside the casing of a pump.