Drain water heat recovery is an uncommon measure in multi-unit residential buildings. There istechnology available for the purpose but the knowing and experience of the heat recovery systems islittle. The purpose of this thesis is to evaluate the future potential of drain water heat recovery inmulti-unit residential buildings.A major part of the multi-unit residential buildings in Sweden were built during modernismen andrekordåren (1940?1975). Many of the buildings have worn out drain and water supply systems andmany are in need of a general refurbishment.

Wastewater treatment is increasingly controlled by the Swedish environmental quality objectives, adopted by the Swedish parliament. There is a need for a sewage system that can fulfill stringent requirements concerning the environment, recycling and resource use and hygiene. Additional environmental aspects in recent years are the impact of climate change, new knowledge about the effects of pharmaceuticals in water, the need for improved wastewater treatment and increased recycling of nutrients to agriculture. This report has, from a future scenario of the year 2050, analyzed seven different systems for wastewater treatment and treatment of compostable biowaste from households in Eskilstuna. A future scenario was chosen based on that within a forty year period new challenges may arise which can result in higher demands on sewage treatment than those we see today. Another reason why the future scenario was established is that changes in wastewater treatment systems are slow to establish. The analysis is mainly focused on the economical aspects but environmental aspects such as emissions to receiving waters and potential recycling of plant nutrients has also been evaluated briefly.

If Swedish companies are to compete with companies in low-cost countries they have to achieve a more efficient production. The purpose of Total Productivity Maintenance (TPM) is to increase the company's profitability by increasing the productivity. TPM is a method that involves all employees and aims to prevent failures in order to increase the availability of existing equipment.The aim of this paper is to evaluate the implementation process of TPM and give recommendations for the further implementation process. The conclusion and the analysis are based on a case study done at a production department at ABB Cewe-Controls facilities in Nyköping. The case study consists mainly of qualitative data from participation observations, surveys and interviews.Commitment of the management is a key factor in the implementation process of TPM.

ERP system is the information technology that has had the biggest impact in companies? development and way of working in today?s world. ERP system is divided in several applications with a modular software design that allow people in every department in a company to store and retrieve information accurately and in real-time. This master thesis investigates attitudes toward ERP systems among business organisations and ERP suppliers with the overall purpose of analysing to which extent a new ERP system will bring change in the business process. The purpose of this thesis is to make a survey of attitudes toward ERP systems among business organisations and ERP suppliers.

Syftet med denna studie var att studera samarbetet mellan inköp och utvecklingsavdelningen utifrån ett kulturperspektiv. Studien grundar sig på teori inom två olika ämnesområden. Ett område är organisationskultur där tidigare forskning visar på hur en gemensam kultur skapar effektivitet inom företag. Det andra området är forskning runt inköp och produktutvecklingsgrässnittet. Då studiens syfte kräver tillgång till ett fysiskt företag så har SAAB Dynamics AB i Karlskoga agerat fallföretag.

As an amateur it can be difficult filming from several angles at the same time as this requires several cameras. It´s also hard to film at occasions when it´s not appropriate to manoeuvre the camera manually. Systems for solving these problems already exist, but it´s either more expensive, professionalsystems or cheaper systems with limited functionality.The purpose of this project is to develop a cost efficient solution to the problem above that offers a better functionality then existing commercial systems. The biggest difference from existing products is the wireless video feedback from the camera to the remote unit.The result of the project is a system consisting of two units, a manoeuvre unit with a cradle for the video camera and a remote unit from which the operator can control pan and tilt of the video camera.Communication between the two units is wireless.On the remote unit there is a joystick and a display mounted. In addition to this, there is also an IR receiver that is capable of reading the signal from the cameras own remote and sending it to the manoeuvre unit.The manoeuvre unit is equipped with one motor to control the tilt function and one motor to control the pan.

The last few years a lot of media air time has been devoted to training, sports, health and weightloss on a more personal level then before. The new media arena is beeing used at its´ maximumto broadcast wievs on how we should eat, look, exercise and live. This thesis is trying to makebetter understanding on what people in general think is important when it comes to physicaltraining and motivation with the aid of digital media and IT systems. The thesis describes aworkshop that was conducted within the frames of Participatory Design and the outcome of thatworkshop. The workshop was conducted with a group of lead users (in this case instructors at avery large fitness center in Umeå, Sweden) and the main question was ?How can IT be used toachive a positive effect on physical exercise if motivation is the focus??.

Aim: To evaluate nurse student?s apprehension of an interprofessional seminar as part of training. Method: A descriptive, qualitative study built on the analysis of 43 questionnaires and one group interview with nurse student?s who participated in the seminar. For the analysis of the collected material we used the method of analysis of contents as described by Graneheim and Lundman.

Problem: Our opinion is that it is important to consider about usability in system development. In this thesis we will focus on usability in point-of-sale systems. The point-of-sale system we base this thesis on is Extenda Retail. Our case study is performed on Ica Kvantum in Bromölla, which implemented Extenda Retail about two years ago. Purpose: The purpose of this thesis is to figure out what important factors there are to consider, in usability aspects, when developing point-of-sale systems, with focus on the cashier.

The market for management training programs is growing and the supply of the service is increasing and getting further diversified. A consequence is a market with a wide variety of definitions of the very concept of development, and subsequently a wide variety of practices and methods to achieve development. The individuals that are subject to these programs seldom know what they are purchasing, or what to expect. When assuming a transfer of the developers view on development to the subject, a need for a greater understanding of the concept arises. The purpose of this thesis is to understand what views on development do exist among management trainers and map underlying dimensions of the views to increase the understanding of the concept of development.

This report summarize what have been done during the Master of Science Thesis that Klas Schjelderup has written for the company RANOTOR Utvecklings AB. The company is developing modern steam engines and this work should develop a machine to perform tests on a new type of piston seal that hopefully could be used in the future. The steam engines will be both volumetric and energy compact, around 1600hp/literof cylinder volume, and it will have a lot of practical applications.The new type of piston seal is hydrostatic lubricated which means that a fluid is separating two faces that normally is in contact. In this case pressurized water is used to separate the piston seal from the cylinder wall. RANOTOR have earlier formulated that at least the expander in the modern steam engine have to be oil-free, due to other components functionality in the closed water system.

In order to maintain a high safety level at a nuclear power plant it is important not only to measure the reliability of the components and systems of the plant, but also to investigate how the plant responds to human actions. One of the most hazardous situations in managing a power plant is fire occurring in critical areas. This study concerns the prospect of the local fire brigade to suppress a fire that has started in one of the most critical rooms for maintaining high reactor safety. The model created gives an indication on the possibilities of succeeding in suppressing a fire. In order to get a more reliable fire fighting the following advice are given:- Let the fire brigade go rounds in the plant together with the personnel, during which recommended fire suppressing methods are determined to avoid long preparation time in an actual situation.- Prepare rooms with two subsystems to make them partly with no voltage.- Give the fire brigade better feedback from actual events on nuclear power plants.- Education and training in suppressing fires in electrical equipment.The probabilistic safety assessment strives to be as realistic as possible.

Scania Top Team is a competition where the best mechanics in the world are competing against each other. In 2011, the world final was recorded and this material is now used to see which problem solving strategies these top of the line teams are using to solve the realistic problems assembled in front of them. To help them, the mechanics are allowed to use two of Scanias IT-systems: Scania Multi and Scania Diagnose and Programmer 3. This report consists of two parts. The first part is the development of a method to analyze the recorded material.

The purpose of this master thesis is to evaluate how internal vehicle information inScania buses and trucks can be used for evaluation of driver performance regardingfuel economy, vehicle wear, traffic safety, emissions and cargo damage. To someextent it was examined whether this information could be used for training the driverto a better driving style. In addition, a prototype for such a system was developed.By first defining what distinguishes a talented driver and how he/she differs from apoor driver, followed by a study of the internal vehicle communication, a system thatin real-time gathers and interprets vehicle data could be developed.The resulting system can with reasonably high reliability detect a number of trafficevents (such as braking, lane changing or hilltops). At each such event, the driver?sbehaviour can be evaluated.

This thesis studies the concept of balance in the management control systems (MCS) of a small Swedish company within the IT-sector. The aim is to evaluate the importance of balance and dynamics in MCS and investigate which factors affect them. The frameworks used are Simons (1994) four levers of control, and the five-factor model for balance and dynamics by Mundy (2010). The small IT company - the object of the case study - has grown extensively in the last years and needs to develop more formal MCS without losing efficiency and creativity in their fast-moving industry. The case study reveals that balancing MCS is important also in smaller companies with less formal MCS.