This thesis is divided in to two different parts. The first part includes examination of the measurementsystem of an industrial robot using a resolver sensor. The main focus is on methods for suppressing noise in the angularvelocity signal without increasing timedelay. Five different methods are investigated. Three of these are based on oversampling: burstsamplingmethod, meanvaluemethod and correlationmethod.

The task in this thesis is the steering of one of Saab Bofors Dynamics robots using Sliding Mode Control, a method they never used before. The robot constitutes a system which in addition to perturbations and uncertainties due to modeling imprecision, hold the difficulty of being highly time variant. In order to be able to keep required performance with uncertainties and modeling imprecision present, the use of robust control methods like Sliding Mode Control is necessary. SMC is based on the states of the system being forced to stay on or in the direct vicinity of a hyper plane in the state space which is chosen in a way that gives the system dynamics desired properties. Other advantages with sliding mode are reduced order dynamics on the switching surface and total insensitivity to some uncertainties and perturbations.

The engine of JAS 39 Gripen, RM12, has recently been equipped with a new flameholder and a new engine inlet. This change has caused an increased noise level from the engine when the afterburner is in use. The noise level reaches its peak when the afterburner is partially used. The problem is thought to be unstable combustion in the regions around the flameholder. A solution to the problem has been proposed by Volvo Aero.

This master thesis includes a description of how a number of sensors are put together in a sensor platform. It also gives a description of how localization and mapping has been performed with data collected from the sensor platform. Localization is a prerequisite for most of the tasks that can be requested from an autonomous mobile robot. In many situations the GPS signal is not available and hence an additional localization system is required. One approach is to apply localization based on landmarks extracted from the robots surrounding.

Dynamiken för en starkt accelerande robot har modellerats. Modellen linjäriseras så att roboten beskrivs som ett linjärt tidsvariabelt system. Denna representation beskriver roboten väl då robotens anblåsningsvinkel, vilket är vinkeln mellan robotkroppen och robotens hastighet, är liten. Eftersom det ej är möjligt att mäta alla robotens tillstånd har en observatör tagits fram i form av ett Kalmanfilter. Problematik vid framtagandet av observatören diskuteras i rapporten.

The goal of this Master thesis has on the one hand been to create a simulation environment for robots, where not only the simulations in this work can be performed, but also similar robot simulations, and on the other hand to study regulators that can increase the possibilities of rejecting disturbances on an industrial robot. The robot model used has three degrees of freedom, corresponding to the three main links on ABB:s IRB7600. The simulation environment is created using Matlab, Simulink, and Robotics Toolbox. It is constructed in a general way and can be used for simulations of other robot objects created in Robotics Toolbox. A gain scheduling is added to the LQ-regulator, where the feedback matrix is varied depending on the arm position in the workspace.

To enable the enhancement of the driver's environment in a forklift, an alternative form of steering has been evaluated. An earlier concept with a combined driving and steering wheel has been exchanged to a concept with two driving wheels. A link wheel has replaced the combined driving and steering wheel. The steering is done through differentiation of the velocities of the two driving wheels. The scope of this master thesis is to create a simulation model, create a control program and to evaluate the concept of two driving wheels.

In the pulp industry, digesters are used to disolve lignin in wood chips. The concentration of lignin is measured and is called the Kappa number. In this thesis, the question of whether an online Kappa sensor, taking samples from the mid-phase of the digester, is useful or not is analyzed. For the samples to be useful, there has to be a relationship between the measured Kappa at the mid- phase and the measured Kappa in the blowpipe at the bottom of the digester. An ARX model of the lower part of the digester has been estimated.

This master thesis studies distributed navigation which isa function implemented in a future network based combat information system to improve the accuracy in navigation for combat vehicles in a mechanized battalion, above all in the event of loss of GPS. In the event of loss of the GPS the vehicles obtain dead reckoning performance through the backup system that consists of an odometer and a magnetic compass. Dead reckoning means a drift in the position that makes the accuracy in the navigation worse. The distributed navigation function uses position and navigation data with measurements between the vehicles to estimate the errors and uncertainties in positions, which are used to improve the accuracy in position for the vehicles. To investigate and demonstrate distributed navigation, a simulation environment has been produced in Matlab.

A helicopter based system equipped with a millimetre-wave fire control radar is studied for improvement of the detection probability for moving ground targets. The system is a pulse doppler radar that sends out the electromagnetic wave in repetitive pulses. The frequency in which radar sends this pulse is called Pulse Repetition Frequency (PRF). The velocity of the moving targets is measured by spectral analysis of the pulses received. With this sort of system some targets will not be possible to detect.

In this final thesis two simulation models have been integrated. The simulation models are models of JAS 39 Gripen?s fuel system, software and hardware. The time consuming and costly work to develop software has made the department of fuel system to build two models in Xmath/Systembuild. The software model also simplifies the comprehension of how the software in the control computer of the fuel system works.

I denna rapport redovisas hur simuleringsmodellen för ljusbågsugnar EAFMelt har uppdaterats med ett modernare och mer användarvänligt gränssnitt för Windows. Simuleringsmodellens noggrannhet och känslighet undersöks där modellen påvisade hög känslighet för variationer i svårdefinierade indata. Modellen har utvärderas med avseende på användning för reglering av syretillförsel i syfte att minimera mängden kolmonoxid i rökgaserna..

In this master thesis a robot arm belonging to an automatic milking machine from DeLaval is investigated. The robot arm is controlled by a pneumatic cylinder and a valve. The goal of the master thesis is to investigate instability problems and to find out if it is possible to solve them by using gain scheduling. Gain scheduling is a type of controller where the parameters of the controller are changed during operation, for example depending on the working point. First a nonlinear mathematical model of the system was made.

The use of spread spectrum signals has increased dramatically in military applications. Finding methods for detecting and positioning of these signals have become interesting research areas for signal intelligence purposes. One method is to measure the time difference of arrival (TDOA) that occurs when two receivers are synchronous and spatially separated. Based on the TDOA-technique an audio-demonstrator has been developed and implemented. This report describes the theory for how sound received in microphones can be used to extract information about the transmitter?s position from the measured time difference.

Det här är ett examensarbete i Reglerteknik utfört på SSAB Tunnplåt AB i Luleå och Luleå tekniska universitet. Igensättningar som beror på att slag, stål och oxider fäster inuti gjutröret har länge varit ett av de största problemen inom kontinuerlig stränggjutning av aluminiumsläkt stål. På senare år har forskare och tekniker intresserat sig för detta problem både i Sverige och internationellt. Igensättningar orsakar många kvalitets- och processtyrnings relaterade problem. De extremt lågkolhaltiga stål med hög hållfasthet och speciallegeringar, speciellt titan, som produceras på SSAB i Luleå kräver extra bra processtyrning.