AbstractTrendanalys av rapporterade störningar vid de svenskakärnkraftverkenAnalysis of trends in reported safety-related events atSwedish nuclear power plantsSafdar KargarThis degree project was conducted at the Swedish Radiation Safety Authority (SSM)as part of the bachelors program in Nuclear Engineering at Uppsala University duringthe spring of 2011.The Swedish Radiation Safety Authority (SSM) has developed a Windows baseddatabase called ?ASKEN? during later years. In this database more than 12 000 eventreports are stored sorted in three categories, category 1, 2 and 3. The databasecontains events from the start of Oskarshamn 1 in 1972 till present time.All nuclear power plants in Sweden are obliged to report any deficiency in theirbarriers and/or the defense in depth in obedience to SSMFS 2008:1.When a failure is detected or there is reasonable suspicion of a deficiency, the eventreport should be classified as a deficiency of category -1, 2 or 3 [1].The event reports are logged and archived in the register of SSM. The SSM task forceAnalys av Störningar på elproducerande Kärnkraftverk (the ASK-group), evaluates allincoming event reports and categorizes them according to established criteria.The aim of the project is to study and analyze the event reports in the database andidentity interesting observations and trends which should be investigated morethoroughly by deeper analysis to establish any positive or negative trends of reportedevents. .

The district heating load is seasonally dependent, with a low load during periods of high ambient temperature. Thermal energy storage (TES) has the potential to shift heating loads from winter to summer, thus reducing cost and environmental impact of District Heat production. In this study, a concept of high temperature borehole thermal energy storage (HT-BTES) together with a pellet heating plant for temperature boost, is presented and evaluated by its technical limitations, its ability to supply heat, its function within the district heating system, as well as its environmental impact and economic viability in Gothenburg, Sweden, a city with access to high quantities of waste heat.The concept has proven potentially environmentally friendly and potentially profitable if its design is balanced to achieve a good enough supply temperature from the HT-BTES. The size of the heat storage, the distance between boreholes and low borehole thermal resistance are key parameters to achieve high temperature. Profitability increases if a location with lower temperature demand, as well as risk of future shortage of supply, can be met.

This report was performed in order to evaluate a new technological measure and focuses generally on a heat pump system to a HWC-washing machine. The client is Asko Appliances AB, a company well known for its environmentally friendly products. The goal of this study was to improve the energy efficiency of a washing machine by combining a heat pump device to the heater of the wash water, in order to reduce the energy consumed for heating the water. Besides reducing the energy consumption in heating the water, the washing machine was required to meet low noise and short operating time specifications. For that purpose, nine trials in three test series have been carried out.

This study is a part of a Swedish research and development project that is about heat-treated wood and is led by the Swedish University of Agricultural Sciences and Luleå University of Technology. Products that are heat-treated already exists on the market, foremost the Finnish brand ThermoWood®, bur the project group want to find out if it would be possible to start a Swedish production with somewhat different applications than what is common today. The heat-treated wood has many attributes that have changed in the heating process. It becomes more biologically durable, it gains stability in form and dimensions and it becomes darker and looses several unwanted extractives such as resin. Disadvantages that can be mentioned are that the wood becomes fragile and the strength properties changes. My main purpose with this study is to look into customer involvement in the early phase of product development. I also want to find out if the customers I interview think that the product is worth working with, which means start a Swedish production.

In cooperate with Asko Cylinda we have developed a new heat system too short the processtime and reduce the energy consume in a dishwasher and still have it too be a class AAA.The environment and quality is important for the company too still be the number one onthe market, If they want too keep that position the product developed of new innovations willbe very important. The systems we have developed are more effective and reduce energy uptoo 25 %. The process time is reduced too less than two hours, from the today two andhalf-hour. The solutions are too heat up the rinse water and the dishwater at the same time,with a new heating system and it make are solutions unique and effective. Its good for thedish and the environment.

Works on transparent paper, also commonly known as tracing paper, have been described as ephemeral or temporary working documents and they usually number large quantities in archival and museum collections. They have therefore previously been considered of lower priority and can be found in poor condition due to a lack of treatment or suitable storage prospects. In addition, transparent paper can be very sensitive to moisture and reacts by deformation or loss of transparency. Due to the volume of these works and the necessity of treatment, there is a call for simple and efficient conservation methods. A common solution in archives for the treatment of water-sensitive works on paper has been the use of heat-activated tissues as they can be applied without the introduction of solvents. There is little published about the use of heat-activated tissues on transparent paper and is mentioned only briefly in existing literature.

The purpose of this thesis has been to determine experimentally how good a peltierelement is to convert waste heat from wood burning. Three different peltier elementswere used in a comparison study. The comparison was mainly done to know howmuch power could be obtained from each element. Even, a circuit with a step-upfunction has been created to give a higher output voltage than the peltier elementitself. The result of the experiments was a low output power, the highest valuereached 2.18W.

I want to look at the possibilities to start selling hot water from a small district heating plant with bioenergy. My reason for doing this project is to look at a new business opportunity for our farm. Our company have less work during the winter time compared to the spring and this project will give us more work during the winter. I also want to take as much material as possible for heating from our farm in order to increase the value of the products from the farm. The project is in a village near us, where we should support a school, a churh, a home for the aged, a kindergarten and a parish hall with heat. In my work I have compared two different alternatives with each other. The first alternative is to put a central heater in one of the buildings, the home for the aged, in which we will burn oat.

This diploma work was performed at the department for radiation physics at the Health University in Linköping. Its aim was to develop a method to retrospectively quantify the absorbed dose in coral. Coral is a material which suites well as a retrospective dosimeter because when exposed to radioactivity its induced free radicals are stable in time. The number of radicals is proportional to the accumulated dose so the dose can be calculated by quantifying the radicals. Therefore, coral can tell us something about the past environment and also be used in dating purposes.A young, modern coral from the Red Sea was studied and also a fossil one which I was given from the Natural History Museum in Stockholm.

This report is made as a literature review, focusing on the work done to increase understanding of efficiency in the categories of substations and secondary heating systems, with respect to the deviation from the theoretically possible cooling off in the distribution network as well as the economic benefit that appear. The main purpose of a considerable part of the literature used in this report addresses the issue of identifying individual causes of reduced cooling in district heating systems. These literature resources have been compiled and summarized as part of the report.The technology of district heating is associated with benefits such as better use of the energy in a fuel. This is the case of cogeneration plants where serial generation of electricity and thermal energy increases efficiency compared with the parallel generation where heat is generated locally and electricity is generated centrally. Serial generation thus allows for lower primary energy demand.

SAMMANFATTNING När man i tidigare undersökningar studerat betesgång för mjölkkor har klimatet på betet inte beaktats. En höglakterande ko producerar mycket värme som hon måste avge till sin omgivning för att kunna bibehålla sin kroppstemperatur. De sätt som djuret kan avge värme på är begränsade och påverkas av flera klimatfaktorer samt djurets genetiska och biologiska förutsättningar. Antalet dagar som registreringar gjordes under denna studie blev av flera olika anledningar få, 18 dagar. Klimatet utomhus under studien registrerat som globtemperatur varierade från 22,4 till 34,7ºC. Då djurskyddslagen skall främja djurens hälsa och djurets naturliga beteende fick en grupp 126 höglakterande kor möjlighet att välja uppehållsplats under tiden 26 juli till 11 augusti. 2004. Korna fördes ut på betet vid niotiden på förmiddagen och var därefter fria att gå in och ur stallet efter egen vilja tills de togs in för kvällsmjölkning omkring klockan tre påeftermiddagen.

The aims of this project were to describe the circumstances around dogs being left alone in cars, to investigate owners? knowledge of the risks associated with leaving dogs in cars and the relevant legislation and, finally, to study how changes in the air temperature and air composition in the car affect the dog. The project consisted of a survey of the literature, a questionnaire part and an experimental part. An important conclusion is the importance of the level of knowledge of owners, since there are several ways in which an owner can prevent their dog from heat stroke and, in the case of an eventual accident, their action can have direct consequences in minimizing the long-term damage to the dog and even whether or not it survives. Fewer than half of the owners in the study knew that for a dog suffering heat stroke, the most important thing is to bring the body temperature down. Only a third of dog owners knew that if a dog is left in a warm car and showing signs of heat stress, then the police should be contacted and the dog quickly helped out of the car.

Heat and power stations are often in need of optimizations. A simulation model is a tool for findingways to optimize the plant. The scope of this diploma work is to develop a simulation model ofBoiler 5 at Mälarenergi AB. Boiler 5 is a circulated fluidized bed boiler that was taken into service inyear 2001. Among the included parts in the boiler are cyclone, convection part andINTREX-chambers.

This degree project has been carried out in cooperation with Enertech AB in Ljungby and is pilot study to automating all current manual soldering. The soldering process accounts for a large part of the processing cost in the production of a heat pump. The process is also a quality risk and has a major impact on the lifetime of the final product.The Main task of this project has been to evaluate automation of the soldering process, to develop automation solutions and a principle layout, to draw the design changes required for the automation and to calculate the supposed solution.This pilot study has resulted in a suggested automation solution using laser as a heat source for soldering. Calculations of the solution show that a automating a laser soldering cell is very profitable..

AbstractWith increasing population and increasing demands for comfort and thus an increase in energy demand, it is necessary to examine various energy-efficiency measures. This work deals with the ability to control the flow through the heating system to achieve the desired comfort with as little energy as possibleA heating system contains of different parts, roughly speaking, you can divide it to three main components: Heat source, Distribution and Heat emitters. All components are working together to bring heat to the building. What is examined in this report are different ways of adjusting the flow and supply temperature and how it affects comfort and energy use in a building.At today ?s date the conventional method is to use a high flow through the heating system, which affects pressure drop and cooling of the fluid.