This masters thesis deals with smoke spread via ventilation systems. One aim of the thesis is to investigate and explain the differences in efforts to prevent smoke spread via ventilation systems in different countries. A second aim of this thesis is to investigate how frequently occurring smoke spread via ventilation systems in Swedish buildings are. A third aim is to investigate how uncertainties in input variables to smoke spread calculations will affect the result of calculation. To be able to do this the most important input variables are identified and analysed.

The report contains three parts. The first part is a summary and overall presentation of thermalcracks and preventing measures against such cracks. This is a theoretical part where theinterested designer can get acquainted with various alternatives, be guided to more detailedliterature, and receive some practical information regarding the design of the respectivemeasures.The second part deals with calculation of the risk for thermal cracks and design of water coolingas a limiting measure. Two complementary methods are reviewed for efficient calculation:?the handbook method CraX1(by Lulea University of Technology) is used for quickverification?finite differential analysis in the calculationtool ConTeSt Pro for more precise projectingHere is also presented a development of existing standards through design of the cooling systemby means of the Bernoulli equation.

The aim of this thesis is benchmarking of the program, based on dynamic programming, that earlier was written to imitate the production planning at TSS.This thesis starts with a chapter about the construction of the DP-program, a shorter description of one and each of the program parts and also a list over the in- and output data in each program part. The DP-program consists of six linked MATLAB-files that together produce an optimized production plan for the different planning groups at TSS. The program reads in and reformat the given data and optimize the production of the articles in one group. Finally it compounds all article production plans and give us a production alternative.After running the program with new data the result shows, resembling with previous results, that TSS could be able to make some distinct cost-savings. According to the program, a 50 % decrease of TSS production costs is possible. .

The regulatory framework for constructional calculations in Sweden did expire In January the 1.st, 2011.Since then the constructional regulatory that originally were composed by Boverket (BKR) has been replaced by new common range (Eurocodes) for the entire European Union. This transition has led to changes in existing rules and standards regarding dimensioning area in Grids and has forced a need for updating to structural Engineers.The new calculation system has caused time-consuming studies of the new rules and a proper understanding of all the advice and regulations for the entire profession.This study has been carried out in cooperation with the firm "Knut Jönson Ingenjörs AB i Stockholm?, that has been affected by this transition as all other consulting firms. The firm has requested for a calculation method of wall beams according to Eurocodes. The study's focus is therefore to clarify the rules and guidelines regarding the design of wall beams according to the new regulation.

The globalization that has occurred during the last few years has made it more important for companies to have a well-functioning logistics system. Customers demand more options, which lead to an increased flow that creates greater demand regarding packaging and transports. Diverse logistics costs are nowadays a substantial cost for many companies. Therefore, more effort is aimed at optimizing transportation to lower these costs.The purpose of this project is to create a user-friendly calculation of logistics costs that illustrates how the costs vary, depending on how the flow is structured. This is done by examining which aspects that affect the total logistics costs and by mapping which aspects that should be included in a calculation of the logistics costs.Literature studies have been carried out parallel with empirical studies at Scania's production unit, MC, in Oskarshamn.

The Work has been performed to, and in cooperation with Vetlanda Energi och teknik AB.District heating for commercial purpose started in the USA in 1877. Today the network has grown into big and complex systems, which demand maintenance and service to keep up the security of the delivery. When a district heating network expand, it becomes difficult to perform reliable calculations. For this purposes there are a few suppliers who design and deliver systems for documentation and calculation of district heating networks.Vetlanda Energi och Teknik AB is in the position where they must get a system for documentation and calculation for district heating, and therefore they need a basis to get a system. The target is to write a requirement specification that will follow the basis.The Swedish market has been inventoried, and suitable systems have been selected.

The Work has been performed to, and in cooperation with Vetlanda Energi och teknik AB.District heating for commercial purpose started in the USA in 1877. Today the network has grown into big and complex systems, which demand maintenance and service to keep up the security of the delivery. When a district heating network expand, it becomes difficult to perform reliable calculations. For this purposes there are a few suppliers who design and deliver systems for documentation and calculation of district heating networks.Vetlanda Energi och Teknik AB is in the position where they must get a system for documentation and calculation for district heating, and therefore they need a basis to get a system. The target is to write a requirement specification that will follow the basis.The Swedish market has been inventoried, and suitable systems have been selected.

ABB is one of the world?s leading engineering companies in power and automation technologiesand their solutions improve performance while lowering environmental impacts for energycompanies and industries. ABB FACTS designs equipment and plants for series and phasecompensation.This thesis has been performed at ABB FACTS on the Mechanical Design (DM) department inVästerås, Sweden. The purpose of the thesis was to develop and design calculations andsimulation tools for ABB FACTS?s standard series capacitor platforms.

In this work, a method was developed and evaluated for calculating the life of welds under the influence of fatigue loads from a vibration environment. Typically, a shaker table is used for testing a component against vibration loads. The shaker table creates a vibration environment that is defined in the frequency domain by a power spectrum.Similarly, a virtual vibration table can be used to calculate the same type of load environment, which can then be used to calculate the expected lifetime. The benefit of this method is that it can be used in design, as well as in simulation of tests before physical verification tests are carried out.Today there are methods for calculating fatigue life of non-welded base material, but since many components contain welded joints, there is a need to apply this method to those types as well. To achieve this, the thesis combines two different areas, which together provide a method for fatigue assessment of welds using a virtual shaker table.The methodology is carried out by modeling the component, and its welded joints, in a finite element program.

Calculations are an important part of planning around a construction project. From concept to completion of the project calculation is a tool to try to predict the actual cost. During the production stage in particular, deviations occur which makes the actual cost different from the calculations.This thesis is done in collaboration with JM Residential Stockholm. The study includes a cost follow-up in which a comparison was made between the calculated production cost and actual cost for the five projects. The aim of the study was to observe the most common reasons that a project deviates from the calculated production cost and then summing these causes in a number of categories.

This report summarizes the development of a calculation program estimating the profitability of converting a peak-load oil-fired boiler to pellets. To convert an oil-fired boiler to pellets a new fuel handling system must be designed. Changes also have to be made to some other components. Since there are many different techniques for transportation, storage and treatment of the fuel only the most interesting techniques from Swecos experience and interest were included in the study.The capacity of the different parts in the system was dimensioned based on the power of the boiler after conversion. To estimate prices, installed power and dimensions manufacturers and distributers were contacted.

Today?s system to measure the volume in a tank consists of a vertically placed sensor. When a vehicle is tilted the level of the fluid might change and if the volume is calculated based only on the information from the sensor it could result in a incorrect value.This thesis exams a new method to calculate the volume in tanks by using sensor fusion to crosscheck the i formation from the level sensors when the vehicle is tilted. The information is then used to see if it is possible to identify the grade of tilt by the change of fluid level. If the grade of tilt can be measured then the volume can be calculated in a more accurate way.

Costs of maintenance on combines are a subject of interest thus it constitute a large investment and cost for the individual farmer. Therefore it is important to have up to date knowledge and the right facts to be able to do reliable calculations on one of the largest investments for a farmer. The aim of this study was to compare costs of maintenance on combine/threshingmachine with the computer program for advising environmental issues in agriculture, STANK. Interviews took place and data were collected by handing out questionnaires to 20 farmers. A similar study conducted by Neuman (2003) investigated costs of maintenance and compared these with STANK. The results of this study have also been compared and examined related to data from SLA - Skogs och Lantarbetsgivarförbundet. The result shows that 18 out of 20 combines were given a higher cost of maintenance when using STANK compared to the numbers in this study.

This is a feasibility study that examines various aspects of building a wind farm on Malmön in Norrköping. The feasibility study deals with interests of conflict, park design, electrical connections, production calculation, financial calculations and operating- and timetable.The report is divided into two distinct parts. First a theoretical part, which deals with conflicting interests, park design and electrical connections. Second a part with simulations dealing with production calculations, and financial calculations.Opposing interests are mapped so that problem areas can be found, and help put focus on the right places at a future environmental impact assessment (EIA). There are a number of areas where planners have to assess on an EIA, this thesis point on the most important areas.

This thesis describes new methods for automatic crack detection in pavements. Cracks in pavements can be used as an early indication for the need of reparation.Automatic crack detection is preferable compared to manual inventory; the repeatability can be better, the inventory can be done at a higher speed and can be done without interruption of the traffic.The automatic and semi-automatic crack detection systems that exist today use Image Analysis methods. There are today powerful methods available in the area of Computer Vision. These methods work in higher dimensions with greater complexity and generate measures of local signal properties, while Image Analyses methods for crack detection use morphological operations on binary images.Methods for digitalizing video data on VHS-cassettes and stitching images from nearby frames have been developed.Four methods for crack detection have been evaluated, and two of them have been used to form a crack detection and classification program implemented in the calculation program Matlab.One image set was used during the implementation and another image set was used for validation. The crack detection system did perform correct detection on 99.2 percent when analysing the images which were used during implementation.