Effektivitet är för många organisationer ett begrepp som förknippas med att utnyttja sina resurser maximalt. Detta är något som även är märkbart inom svenskt skogsbruk, där man idag är mycket mån om att vara resurseffektiv i sin verksamhet. Det finns dock fler innebörder av effektivitet som begrepp. Toyota, med sitt Toyota Production System, och lean production har bevisat att en flödeseffektiv process med kundfokusering kan vara ett framgångsrikt arbetssätt. Denna studie tar upp lean production som teori i svenskt skogsbruk och knyter an denna mot virkesanskaffningsprocessen.

The E-department at GETRAG All Wheel Drive in Köping have problems with the efficiency on parts of their production equipment. The equipment with the most significant efficiency problems are four automated multifunctional production cells that produces housing for rear drive units. The major part of the problem is the large amount of small stops that causes the low efficiency.The department already worked with logging of interruptions and efficiency calculations before this project started. However this work was not done to the extent considered necessary for a systematic follow-up of the interruptions.The aim of this paper is to point out a more effective and systematic way to work with logging of interruptions and the follow-up. In addition the equipment were studied with a method for efficiency calculation that ? if used properly- is a more powerful and a visually better method than the one used by the company today.As the initial current state analysis of the equipment was made a lack of documented knowledge about the equipment was discovered.

The biogas plant Kungsängens gård, owned by Uppsala Vatten och Avfall AB, produces biogas and biomanure from organic household waste, food processing waste and slaughterhouse waste. In year 2012, 4.4 million Nm3 of biogas were produced from 25 200 tons of waste. Before digestion all substrate is sanitized by pasteurization at 70°C in order to kill pathogens. Another method, integrated thermophilic sanitation (ITS), is of interest in order to decrease the energy demand. The method implies that the substrate is sanitized during ten hours in the digestion chamber, where the temperature is 52°C.

This is a technical report about cement stabilization in general and the stabilizationprocess during the construction of a warehouse in Halmstad, Sweden in particular and iswritten at the section for economy and technology at Halmstad University incollaboration with NCC Anläggning.NCC encountered variations in compression strength in the stabilized material on the firstwarehouse that they constructed for the company Biltema. In our report we used thestabilization process of the second warehouse for the same company as a reference todetermine what could be done to get a more homogeneous result for future projects.We also looked in to what testing method is the most suitable to determine the result ofthe stabilization.After interviews with people involved in the process and visits on the work site we havecome to the conclusion that the most probable cause to the variations in compressionstrength is segregation in the ballast material. This segregation can occur in severaldifferent occasions in the process such as during the production, transportation andhandling on the work site.Other causes for the variation can be improper compaction, overlapping stabilization insome places and different duration of hardening of the samples that are tested.The best way to do in situ test of the stabilized material is to do seismic investigations asthose are non-destructive tests in comparison to taking core samples and you can discoverany cracks or air bubbles in the material..

The development of productivity in the construction industry has long been at a steady state compared to the manufacturing industry. Studies have shown that, amongst other things, waste on construction sites can reach up to one third of the total production cost. This has been observed from different aspects, and change is forthcoming.This thesis aims to provide a foundation for an increased productivity at production sites of building bridges. It is primarily based on a field study at Skanska, at a bridge construction site near Grängesberg. Via continuous interviews with the whole production crew, construction workers and management, information on interference and possibilities of improvement at the work site has been documented.

StoraEnso decided in year 2002 to build a pulp mill in the province of Guangxi, southernChina, and also establish eucalyptus plantations to provide it with raw material. By 2010StoraEnso controls about 90 000 of planned 120 000 ha, out of 75 000 ha is already plantedwith Eucalyptus.By using better genetic material, improve the tending, selecting the sites more careful and byusing a proper fertilization regime StoraEnso hopes to increase the mean annual incrementfrom today?s 25 m3/ha, on bark, to 35 m3/ha. This study is one part in this work to increase themean annual increment in the plantation.This master thesis is the forth in a series, that has followed up a fertilization trial that startedin spring 2006 when the trial was laid out and treatments decided. The aim with the trial is toexamine the production potential of Eucalyptus urophylla in Guangxi, southern China.

There are several factors influencing the profitability of production with sheep. Two of the most important factors are ewe fertility and lamb survival. Also growth capacity of the lambs is important. This paper aims to review correlations between the ewe?s fertility and maternal behavior and lamb survival.

In 2005, Outokumpu began to implement its system of continuous improvement, OK> 1, at Avesta Jernverk. OK> 1 has not generated sufficient results on plant KPI:s. The purpose of this study is to identify the understanding,  participation and commitment regarding to OK> 1, and to suggest some actions to make OK> 1 more successful with emphasis on these three aspects. The thesis shall also determine whether there are any differences in the attitude towards OK>1 between Blue Collars and White Collars.The study consisted of a survey, and interviews. The output from these methods were processed and analyzed and finally resulted in a SWOT ? analysis and suggested actions for improving the understanding, participation and commitment towards OK>1.

All companies wants? to be as profitable as possible. The company in question is one of the leaders in it´s field in Sweden. In order to increase profits as much as possible it is important to identify and eliminate eventual quality defect cost as far as possible.This study was performed in Huddig AB, and the purpose of this study is to try to develop a routine for monitoring the quality defect costs, and to improve communication and create feedback between production and aftermarket.In addition to an extensive literature review on quality defect costs most of the work have been conducted at the company. Own observations and interviews have been done with the staff to get a picture of the current situation and to try to come up with improvement proposals.During the study it was proved that much of the quality defect costs in essence, derived from the production, which is seen as positive because it is the easiest part of the company to improve.

Bakgrund: I takt med att konsumenters preferenser har förändrats, har företag fått överge massproduktion till förmån för produktionssystem som bättre avspeglar konsumenternas ökade krav på flexibilitet. Ett sätt för att överbrygga denna utmaning är att implementera lean production. Även om detta sätt att producera på har tydliga fördelar för dagens företag, verkar lean production även kunna medföra problem i avseende på att kombinera med den befintliga, i många fall, traditionella styrningen i företaget. En del av styrningen som verkar vara speciellt svår att kombinera med implementeringen av lean production rör mätningen av produktionen. Vid en närmare granskning visar det sig att det råder vissa motsättningar mellan traditionell mätning och lean production som kan påverka företagets beslutsfattande negativt.

This project is a learning CD-ROM production aimed at first-time parents. It is using both sound and images, moving as well as non-moving. The purpose of the production is to be an interesting alternative to traditional books. We have been looking at similar productions like drivers license educational CD-ROMs and encyclopedias for inspiration and ideas on how to proceed. In order to give the content some dynamics, we've also added the element of 3D-animated sequences. The application is supposed to be run as a simple executable file with flash embedded.

This study was a final thesis, for the bachelor program in civil engineering at theUniversity of Uppsala, which was made on behalf of Riksbyggen in Uppsala. Acomparative study of two stain renovation methods; tradition pipe replacement andrelining was done with an environmental perspective. A simplified life cycleassessment (LCA) was done according to the International Organization ofStandardization (ISO) with the LCA tool Eco-indicator 99, in order to be estimate theimpact on the environment. LCA is a method that follows a product or a system?from the cradle to the grave?, which means that all the environmental impact over alifetime is considered.The work was executed by using a stairway with nine apartments in a house called?Uppsala Hus 9? as a reference object, which was provided by Riksbyggen.

This report investigates the possibility of developing a new and improved hip prosthesis. The result were five different materials that could be used for the prosthesis. These five solutions were Silicone Nitrate on Cobolt Chrome, phase stabilized Zirconium Oxide on Cobolt Chrome, Silicone Nitrate on Silicone Nitrate, DLC coated phase stabilized Zirconium Oxide and Chromium nitride coated Cobolt Chrome on Cobolt Chrome. In addition to this it was also investigated how to best market the prosthesis and how to transport them from production sites to hospitals..

This master thesis is about the production of the record ?Brutus? with the band ?Trilobit?. Trilobit consists of the three musicians, myself, Stina Hellberg Agback on pedal harp, Simon Sva?rd on guitar and Karl Jansson on drums.During the production, I have analyzed different aspects of my own musicality and also the role of the pedal harp in jazz. I have found techniques that have simplified chromatic movements on the pedal harp, and also techniques that has developed the rhythmical aspect of my improvisation.I have also looked into my process in improvising and composing and developed new aspects, many thanks to the close collaboration with Simon Sva?rd..

In Kenya the Maasai pastoralists have based their livelihoods on dairy production and the production goal is to maintain a sufficient milk supply throughout the year. The pastoral dairy production has two vital characteristics; breeding and milking. Traditionally, breeding is the men?s responsibility, while milking is the duty of women. Depending on this partition of chores between men and women, they also have different management routines, ambitions and strategies regarding the milk production.