Lean has been studied intensely since the 1980s and it has been tested and successfully implemented in a wide variety of businesses. This thesis aims to examine the potential effects of a Lean implementation on meeting efficiency, a topic that has gotten little attention in the research community. First, a number of meeting problems are introduced, as they are perceived from the company that is the subject of the study. Second, the potential of introducing Lean in a meeting process is evaluated using the Lean Thinking principles. Third, the wastes that are generated from the meeting problems are identified.

As the companies of today are good at protecting themselves against external threats, but are having problems with internal threats, we focused on how information can be protected from ending up in the wrong hands. First and foremost to protect information from employees who might steal it and sell it to another company. Since the security investments needed are connected to the financial costs of implementing them we have tried to create a balance between the investments needed and the cost of implementing them. The different kinds of protection needed are first and foremost protection to make data less accessable, passwords and traceability. While it is hard for us to estimate the amount of money a company lose by the hour when the production stands still, we have not been able to use any of the excising models to calculate the profit of installing countermeasures.

AbstractThis bachelor?s thesis at the Department of Production Engineering at the Royal Institute of Technology in Stockholm deals with the subject of automated metrology. The degree of automation of tasks within production has been a growing trend but the measurement of quality has not followed the same trend. The main thesis follows:What incentives are there to automate the measurement of quality in production?What factors are crucial and why are not all metrology automated?The thesis comes along with a number of sub-queries and delimitations.The working method includes both theoretical and empirical studies.

Value stream mapping is a tool that is frequently used by many different companies. It is a great tool used to achieve the work that follows the theories of lean production. The tool is used, however, only frequent on the factory floor and the method is also designed based on this type of use.An interest of applying the method on administrative parts of the company has occurred lately. Administrative parts of the company refers to the part that does all the planning such as purchasing, receiving orders, customer contact, contact with factory floor and other work that is made around the actual manufacturing. But the knowledge about applying value stream mapping on the planning part of the company is lacking because the method is relatively new.In this work, a comparison is made between the introduction of value stream analysis on production and planning.

Problem: The corrugated board industry is highly affected by customer uncertainty, various demands and short delivery times. In combination with a complex multi-step production process managers have to be able to identify bottle-necks and gain knowledge and understanding of how different changes in process will affect the production output. <br/><br/>Purpose: The purpose of this master thesis is twofold, (1) to examine applicability of complexity theory through agent-based modelling on a production process (2) to identify improvement areas in order to increase the production output at SKS production site in Eslöv, by modelling and simulating the production process through an agent-based model. <br/><br/>Method: The chosen method of this study is a combination of a case study and a complex system approach. The empirical data was collected through interviews, observation and document studies which were analysed through an agent-based simulation model.

Value stream mapping is a tool that is frequently used by many different companies. It is a great tool used to achieve the work that follows the theories of lean production. The tool is used, however, only frequent on the factory floor and the method is also designed based on this type of use.An interest of applying the method on administrative parts of the company has occurred lately. Administrative parts of the company refers to the part that does all the planning such as purchasing, receiving orders, customer contact, contact with factory floor and other work that is made around the actual manufacturing. But the knowledge about applying value stream mapping on the planning part of the company is lacking because the method is relatively new.In this work, a comparison is made between the introduction of value stream analysis on production and planning.

AB Sandvik Cormorant?s production unit in Gimo has identified a need to examinethe handling of products between operations with the purpose of generatingproposals of improvement for the product handling.The aim of this project is to study the existing manufacturing process and givesuggestions for improvement. The proposals should reduce the manual handling ofproducts, decrease the risk of damaging the products during the manufacturing andform a basis for increased traceability. Based on a mapping of the manufacturingprocess and the problem description, a specification of requirements has beencomposed.The mapping of the manufacturing process suggests that a change of the currentsystem is required. The company is recommended to decide how the producthandling between operations should be performed as guidelines for the productionteam.

During year 2004 Ålö AB made significant change in their production process. The production of front loaders is nowadays highly automated with short operation times. To be able to control their process in a better way Ålö recently decided that they needed a tool for simulation of their production and to shift patterns. This final thesis started with a pilot study in Ålö?s factory in Brännland.

The aim of this thesis is benchmarking of the program, based on dynamic programming, that earlier was written to imitate the production planning at TSS.This thesis starts with a chapter about the construction of the DP-program, a shorter description of one and each of the program parts and also a list over the in- and output data in each program part. The DP-program consists of six linked MATLAB-files that together produce an optimized production plan for the different planning groups at TSS. The program reads in and reformat the given data and optimize the production of the articles in one group. Finally it compounds all article production plans and give us a production alternative.After running the program with new data the result shows, resembling with previous results, that TSS could be able to make some distinct cost-savings. According to the program, a 50 % decrease of TSS production costs is possible. .

Shareholder, who decides to continue with the company, can cause that they become per-sonally liable for its upcoming obligations. Creditors must lodge an appeal against the shareholder to get compensation for the harm they have suffered. The damage rules in Swedish company law are designed to utilize the company?s interest, that is, shareholders and other corporate members shall promote the interests of the company and not cause damage.The rules about compensation that shareholder obligates itself to are difficult to apply and are adapt to the specific cases. For a shareholder to be personally responsible in a real situation a company has to establish a subsidiary company, which is being driven undercapitalized, intended to benefit the shareholder.

This study is preformed at Westbaltic Components placed in Töcksfors Sweden. Themain target in this study is to make one of the company?s assembly lines better andmore effective. The assembly line constructs vending machines for different stores allover Europe.It will contain tobacco, snuff, cigarettes and shaving blades and many more similarproducts.The first step in our study is to locate the daily problems and find out a good way toreduce them and make them disappear. A good way to do this job easier was toconstruct a visualizing board.

This thesis has been carried out at Diac Metal AB at Torsvik outside of Jönköping. The company produces parts for, amongst others, office furniture and store equipment. The essay will be concentrated on one detail which is included in many of their products.Today the company uses an ordering quantity based on experience which is rarely updated. Furthermore the operations are performed in both the company?s own engineering workshop but also an external workshop.The purpose with the report has been to check whether an updating of today?s batch shaping and ordering system can mean simpler storage control and possibly cost reduction.

This report is about logistic efficiency in companies without own production. The authors have interviewed employees working at two companies, Telias store in Skärholmen and Orion Diagnostica AB. The purpose of the report is to find out which logistic functions the two companies are using to create efficiency.Today?s markets are more global. Different parts of a product can be made in different parts of the world.

Value stream mapping is a tool that is frequently used by many different companies. It is a great tool used to achieve the work that follows the theories of lean production. The tool is used, however, only frequent on the factory floor and the method is also designed based on this type of use.An interest of applying the method on administrative parts of the company has occurred lately. Administrative parts of the company refers to the part that does all the planning such as purchasing, receiving orders, customer contact, contact with factory floor and other work that is made around the actual manufacturing. But the knowledge about applying value stream mapping on the planning part of the company is lacking because the method is relatively new.In this work, a comparison is made between the introduction of value stream analysis on production and planning.

The aim of this report is to analyse the use of the capacity at the CNC (computer numerical control) cutters and show how the level of set up time for these cutters at Stålöv AB. This assignment is concrete whereas there are no subjective questions to this matter and there are only cold figures presented.Production economy is getting more important as the competition hardens and there are several different ways to increase productivity and efficiency in a company. In order to increase productivity and efficiency work studies are used to, through an analysis, find developments in methods that result in improved work methods and to establish the time that are used. Increased production of different parts and customer driven production in combination with increased demands on rationalisation of capital have led to an enlarged interest for shorter set up times in the production.To point out the use of capacity and the set up time of the cutters at Stålöv AB we used frequency studies. Frequency studies are work measure methods based on random observations on predetermined events to calculate the relative occurrence of these events.