During the late twentieth century, political and societal changes gave rise to an increased interest in performance evaluation in public organizations. This development also affected libraries in the public sector. The main concern for this master thesis is performance measurement in libraries. In this study two different types of libraries are investigated, one public and the other academic. My aim is to find out if and how performance measurement appears in the libraries annual activity reports.

Landfill leachate contains a variety of contaminants and is created when rainwater percolates the landfill. For landfill management the leachate is the main issue that can cause problems to the environment. At the landfill of Fläskebo, Renova AB treats the leachate in a local treatment plant. The treatment consists of a chemical treatment step with chemical precipitation, flocculation, sedimentation and filtration, and a final step with a carbon and peat filter. Renova has to ensure that the condition of the leachate reaches the regulation set for the landfill before it is released to the recipient.

This project investigated how elevation and vegetation type influences variation in plant litter phenolic content and protein precipitation capacity among and within common plant species for two different vegetation types, heath and meadow, in a subarctic ecosystem in the Abisko region of northern Sweden. As nutrient availability generally decreases with increasing elevation as a result of decreasing temperature, I hypothesised that phenolic content would increase with elevation and be higher on the heath than the meadow. To test this, the total phenolic content and protein precipitation capacity was estimated in leaf litter from 13 species in both heath and meadow vegetation across an elevational gradient ranging from 500 to 1000 meters above sea level (m.a.s.l.) in the study region. The results showed that elevation and vegetation type both had a strong impact on both variables. Total phenolic concentrations decreased with elevation for the meadow, and were greater for the heath than the meadow.

The aim of this Bachelor´s thesis is to investigate how library statistics, performance measurement and indicators represent the modern public library activity. During the last decades the public library has gone through a lot of changes. Information overall has increased and new technology has been introduced into the library. This new development has had effects on the library users. The statistics reported to the Statens kulturråd (National Arts Council) has not changed in the same way.

The aim of the thesis is to analyse and understand resolution, repeatability and reproducibility of the measurement system for package distance. The measurement system for package distance is already in use, no Gage R&R has been performed on the system and before spreading use of the system the quality of the system has to be understood and approved.

Bachelor thesis, Business Administration and Economics Programme, School of Business and Economics at Linnaeus University in Va?xjo?.Spring of 2015 Title: Performance measurement from a cost leadership perspective - A case study on Gekås.Authors: Adrienn Csiszer, Hannah Lundberg & Helena WennerströmTutor: Eva GustavssonExaminer: Karin Jonnergård Keywords: Performance measurement, Performance measurement systems, Generic strategy, Cost leadership strategy, Financial and non-financial measurements. Purpose: The purpose of this study is to examine how a company with a clear cost leadership strategy chooses to work with performance measurements, with a view to comparing a practical example to theorethical approaches. Methodology: The method chosen for this paper is a case study on Gekås AB. The presented data were collected through interviews conducted with four employees on Gekås. Conclusion: The study concludes that for a business with cost leadership strategy the financial measurements are more important than non-financial meausurements. For Gekås it is important to keep the performance measurement simple and understandable for the employees. They only use three measurements (sales, hours and sales per hour) in planning and in evaluation.

This thesis deals with different methods for measuring moisture-related dimensional changes ofwood. Typically relative humidity is measured to determine if the ambient climate around anobject is harmful to it or not. Values between 40 to 65% RH are recommended for hygroscopicmaterials. To know how a wooden object actually reacts to changes in the surroundingenvironment requires methods that involve the object itself. Because of the wood anisotropy,differences in wood structure, finishes and other restraints, it is not always possible to predict themovements.This paper addresses various measurement methods, primarily methods that have been testedin the field of conservation, with examples of their use.

The aim is to describe the factors that influence nurses' assessment and measurement of pain in patients. Literature study based on 13 reviewed articles, searched in the Cinahl. Qualitative and quantitative articles were analyzed. Six themes were identified that can be seen as the factors that influence nurses' assessment and measurement. The themes were   pain education, nurses´ experience in the profession, nurses´ level of knowledge about pain relief, documentation about pain, nurse´s perspective on the patient, and pain measurement.

Risk-based sampling program of microorganisms in the water source in northern SwedenAfter several disease outbreaks caused by parasites in the drinking water during the last years, it is more essential than ever to insure that the water supply companies have enough barriers to counteract the presence of microorganisms in the outgoing water. It is also discussed whether climate changes such as increased precipitation can have a connection to the increased cases of parasites in water sources. The water source at Gäddvik is Luleå municipality?s largest and provides drinking water to 64 500 of Luleå?s 74 000 inhabitants. The investigation of microorganisms in the water source, especially in the Lule River has not been as prioritized as the sampling of chemical parameters.

The acoustics in a control room is a complicated phenomenon. Early reflections, reverberation time and area in the room are some of the problems. This report is about the reflection on the mixing console in a control room. The control room being built, these reflections are difficult to take into consideration since the mixing console is one of the very last items you place in the room. This report will explain three main measurements that were done in order to get the answer to the following question: Does the mixing console interfere the frequency curve at listening position? Three measurements were done and the difference between the measurements was that the microphone and the loudspeakers were placed in different places in the control room.

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

A system for sampling of alcohol and aldehyde from diluted exhaust gases from vehicles powered by ethanol has been developed and tested. The major part of the work has been research of earlier work in the field and the construction of the sampling system.The part of the system constructed for the measurement of alcohol has been shown to work, however, more test should be performed. The part of the system constructed for the measurement of aldehyde was tested parallel to a commercially available system, based on the same principle of measurement, and has been shown to work well.Determination of the concentration of gaseous ethanol using a FID has shown the since earlier known fact that a FID is not able to measure a correct concentration of ethanol. Furthermore it has been shown that high concentrations of gaseous ethanol can not be kept in a bag more than a few minutes without a substantial decrease of the measured concentration..

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.