The sun is an endless energy source and the heat it produces can be used to heatup our homes. This technology is relatively old and was introduced in the late70-s. There are two kinds of solar collectors that are most frequently used todayand these are plain solar collectors and vacuum solar collectors. The plain solarcollectors are the once that are used the most but the vacuum solar collectorshave increased more as a percentage the last couple of years.The biggest question asked regarding an investment in solar heating is if theplant is economically profitable. This question has no direct answer because itis dependent on a couple of prerequisites.

The sun is an endless energy source and the heat it produces can be used to heatup our homes. This technology is relatively old and was introduced in the late70-s. There are two kinds of solar collectors that are most frequently used todayand these are plain solar collectors and vacuum solar collectors. The plain solarcollectors are the once that are used the most but the vacuum solar collectorshave increased more as a percentage the last couple of years.The biggest question asked regarding an investment in solar heating is if theplant is economically profitable. This question has no direct answer because itis dependent on a couple of prerequisites.

This essay concerns the visual trade grading of pine and spruce.In the 1800s developed rules for sorting of wood. The rules used to facilitate the export trade.The terms of the regulatory sorting systems developed in the 1900s. While it still used some of the older terms.The essay deals with how the grading rules affect the use of wood and how the rule work and how the terminology works.Some of the terms used for sorting are O/S, Kvinta, Utskott and A,B,C,D.You sorting by counting the numbers of knots, cracks and other characteristics of each piece of wood.The sawmills have much influence in how the rules developed.Today it is often already determined in the sawmills which uses each piece of wood most have..

A large amount of our time is spent indoors in an artificial climate. To make the experience pleasant there are requirements on the ventilation and the heating system. At the present time the most common form of heating is a radiator system complemented with a ventilation system. A ceiling heating system with combined heating and ventilation can replace the two separated systems. The benefit with a ceiling heating solution is that it saves space since the radiator system is no longer needed.

Design of a house requires knowledge of both technology and economics. Heating and ventilation shall be designed, costs are calculated and estimated and requirements must be fulfilled. Which heating system is to be elected is also a difficult choice, especially with rising energy prices as a factor.The choice of energy system is not always given, because it depends on several factors. Below is a comparison between district heating, geothermal heat pump and electric boiler from an economic standpoint. In a previous report appears district heating and geothermal heat pump as the best options.

The sun is an endless energy source and the heat it produces can be used to heatup our homes. This technology is relatively old and was introduced in the late70-s. There are two kinds of solar collectors that are most frequently used todayand these are plain solar collectors and vacuum solar collectors. The plain solarcollectors are the once that are used the most but the vacuum solar collectorshave increased more as a percentage the last couple of years.The biggest question asked regarding an investment in solar heating is if theplant is economically profitable. This question has no direct answer because itis dependent on a couple of prerequisites.

Forest management plans have been sold to private forest owners by wood supplying companies for a long time. These plans are considered to be effi-cient tools to identify measures and wood volumes, and are simply a starting point for discussions between private forest owners and round wood pur-chasers. However, large variations are observed between different purchas-ers, in their usage of the plans. The purpose of this report is to identify to what extent a forest management plan can promote an increase in the amount of wood which a round wood purchaser can obtain and to find differences in the way of using the plans between different wood purchasers. Furthermore, the purpose is also to ana-lyse if varying owner structures can be underlie variations in the selling of forest management plans. Qualitative interviews with nine of Stora Enso?s round wood purchasers were performed.

Tomo Hugglink (TOMO Skog) is an innovation for harvest and transport of biofuels. The system consists of a truck, a chipping unit and crane mounted on a link and a wood chip trailer. The system works in such a way that the chipping unit is disconnected and placed on the site and wood chips are loaded directly into the wood chip trailer.The aim of this study was:- To examine the performance of the TOMO Hugglink system under different conditions such as the size, placement and quality of the pile.- To calculate the cost per raw ton for two vehicle combinations at different transport distances and to examine the effect of a reduction in set-up time and an increase in load weight.- To identify possible improvements with the TOMO Hugglink system.A time study was conducted within the thesis work to make it possible to determine production and time consumption. In the subsequent economic analysis the cost per tone at different transport distances was calculated for two different lorry concepts. Furthermore the effect of a reduction in set-up time and an increase in load weight was calculated.Under current conditions the utilization of the chipper is low and only 29 % of the total system time is occupied by chipping.

Fuel pellets are in Sweden mainly produced from sawdust and cutter shavings. Before the pelletising process the raw material is dried to attain consistent moisture content and ground up in a hammer mill. In the densification process (pelletising) the ground material is forced through holes in a rotating die. This heats up the wood particles which cause them to soften and self bond. After the process the pellets are cooled, sieved and bagged. The milling process creates a wide range of particle sizes.

The sun is an endless energy source and the heat it produces can be used to heatup our homes. This technology is relatively old and was introduced in the late70-s. There are two kinds of solar collectors that are most frequently used todayand these are plain solar collectors and vacuum solar collectors. The plain solarcollectors are the once that are used the most but the vacuum solar collectorshave increased more as a percentage the last couple of years.The biggest question asked regarding an investment in solar heating is if theplant is economically profitable. This question has no direct answer because itis dependent on a couple of prerequisites.

In this report a study has been done regarding different heating systems on which are the mostcomprehensive with solar heating systems. The report has also been focusing if solar power can beused as a primary heating source for supplying more than 50 % of the buildings total heatingproduction. The University of Dalarna constructed a demo-house for this purpose and according tocalculations the total solar usage is more than 50 %. This house has been made for referenceregarding the design of the heating system of property 5:37.Further studies have been made to compare different heating systems that are compatible with asolar system, where the compared systems purpose is to be independent of direct using electricity. Asystem of this design is regarded as sustainable according to environmental as economic issues.

In this Thesis the possibilities of designing a larger building that is very energy efficient in the sense that it would not need a conventional heating system are discussed. Solar radiation transmitted through the windows, internal heat from occupants, lamps and electric appliances inside the building and heat recovered from the ventilation system then have to be sufficient for the heating of the building. This study is of general interest since the property company, Akademiska Hus, plans to use this study as a first step in determining if this technique could be used in the future and thus be worth further investments. A building without a conventional heating system of the size investigated in this project has not yet been built.The energy needed for the heating of the building was simulated using VIP+.The conclusions from the study are that it is possible to build large buildings without any conventional heating system. This could be achieved in many different ways, for example by lowering the inside temperature or by using better windows and heat recovery system with higher efficiency.

The energy use in a workshop company has been examined in this work in order to find areas for energy efficiency improvement. The combined oil and electricity heating in the company were compared with other alternative heating systems including cooling of the premises in following combinations:Ground source heat pump for heating and coolingDistrict heating and absorption coolingDistrict heating and low temperate surface water coolingEnergy use, operation costs and carbon dioxide emissions were calculated for the current heating systems and the three alternatives including cooling. The ground source heat pump for heating and cooling decreases bought energy with 34 MWh annually compared to current heating only. The district heating and low temperate surface water cooling has the largest reduction of operation cost and carbon dioxide. The operation cost decreases with 42 kSEK and the carbon dioxide with 43 metric ton CO2 annually.

This bachelor thesis aims at investigate how a specified house can optimize its energy consumption.Today the house often stands for the major part of the energy consumption in a consumers? life,whereas an energy optimization creates economic as well as environmental advantages. It is importantto make old houses more energy efficient, but putting high energy demands on new houses could beargued to be more important. The installations functions as both the heart and brain in a house, thusmaking it important to energy optimize these. Since the background describes the importance ofenergy efficiency and optimization in a house, the focus area of this report will be an investigation ofdifferent types of heating systems in order to be able to choose the one most suited for the house.Aspects considered when choosing the heating system was how economic the system is both inservice- and investment costs and how environmental and operational friendly the system is.Through literature reviews there were sufficient information gathered that served as a foundation whencomparing and choosing between the four systems - district heating, pellet-fired boiler, geothermalheating and solar heating.

Life Cycle Cost, often abbreviated as LCC, is a common tool for comparing the total cost of different alternatives, such as heating and cooling methods. Common heating and cooling methods in Sweden are geothermal energy, district heating and district cooling. This report aims to evaluate how different heating and cooling methods differ from each other while being applied on three different types of buildings, using selected LCC-models. Information about the selected LCC-models wasretrieved from each separate model and its website. Reports and agencies were used as sources for information about the heating and cooling methods.