The acoustics in a control room is a complicated phenomenon. Early reflections, reverberation time and area in the room are some of the problems. This report is about the reflection on the mixing console in a control room. The control room being built, these reflections are difficult to take into consideration since the mixing console is one of the very last items you place in the room. This report will explain three main measurements that were done in order to get the answer to the following question: Does the mixing console interfere the frequency curve at listening position? Three measurements were done and the difference between the measurements was that the microphone and the loudspeakers were placed in different places in the control room.

Hofstede constructed a culture dimension called Power Distance, measuring the inequality of Power. Germany and Sweden have relatively similar values according to his world-renowned research. But a series of interviews of Swedish entrepreneurs in Germany shows that these perceive a large difference in inequality of power in the two countries. This essay seeks to explain the difference between these subjective-qualitative experiences and the objective-quantitative data of Hofstedes Power Distance Index. We propose that a combination of differences in communication, exercise and visibility of power and formality influence the way Power Distance is perceived.

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

A system for sampling of alcohol and aldehyde from diluted exhaust gases from vehicles powered by ethanol has been developed and tested. The major part of the work has been research of earlier work in the field and the construction of the sampling system.The part of the system constructed for the measurement of alcohol has been shown to work, however, more test should be performed. The part of the system constructed for the measurement of aldehyde was tested parallel to a commercially available system, based on the same principle of measurement, and has been shown to work well.Determination of the concentration of gaseous ethanol using a FID has shown the since earlier known fact that a FID is not able to measure a correct concentration of ethanol. Furthermore it has been shown that high concentrations of gaseous ethanol can not be kept in a bag more than a few minutes without a substantial decrease of the measured concentration..

Our essay is about children's exercise of power, oppression or domination in games or when playing on school grounds with one and other. We thought it would be interesting to look into how children in preschool and up to the fifth grade use power acts respective power plays in leisure-time. During four days we visited two different after-school center and carried out observations of children during the school day and later inside the recreation centers during leisure activities. In order to analyze our empirical material in relation to power, we have used Magnus Hörnqvist (2012) interpretation of Michel Foucault's theory of power - Another Foucault. We have also used Åsa Bartholdsson (2008) thesis about The regular exercise of power regime ? about normality and power in school.

Scania CV is one of the world's largest truck manufacturer. It is not only the directproduction of vehicles and methods that are important for Scania but also the servicemarket handling spare parts, repairs and workshops. The department Vehicle ServiceInformation construct standard times through work measurement for particularworks in the workshops. The software application STAM is used in the servicemarket to create and store standard times which then are exported to theworkshops' own systems.The purpose of this master thesis is to analyse and evaluate the internal workmeasurement system that includes standard times and the software STAM. Also,based on external analysis and benchmarking of other systems suggest appropriatefuture development within the area for Scania Vehicle Service Information.In order to perform the investigation, interviews and studies have been doneinternally at the departments that are involved in work measurement as well asexternally at Scania workshops.

The aim is to describe the factors that influence nurses' assessment and measurement of pain in patients. Literature study based on 13 reviewed articles, searched in the Cinahl. Qualitative and quantitative articles were analyzed. Six themes were identified that can be seen as the factors that influence nurses' assessment and measurement. The themes were   pain education, nurses´ experience in the profession, nurses´ level of knowledge about pain relief, documentation about pain, nurse´s perspective on the patient, and pain measurement.

This thesis treats the normative power of the European Union and its affect on Macedonia. The main purpose has been to look closer with the use of the application of Ian Manners theory of normative power on the Macedonian case. The focus will be to answer the following questions: Does the European Union act as a normative power in relation to Macedonia, if so, how are these values diffused? Has there been any effect of the spreading of these values? Based on six interviews and the available material of European Union strategies for the Macedonian membership I have attempted to understand to what extent the European Union?s normative power has had an influence in Macedonia. The result of my analysis is confirmation of the European Union as a normative power in Macedonia and the understanding of the methods of application..

Today?s electrical grid companies understand that better knowledge of and information about their grid can help realize a smart grid network. One way to gain better knowledge and information about the low voltage network is to install measuring equipment on the substation transformer´s secondary low voltage side that measures the low voltage network losses for that specific substation. By doing so, grid companies can, due to the calculation of the low voltage network losses, identify and address issues such as illegal power dissipation, unmeasured power outtakes, and unsatisfied technical documentation for the substations low voltage network.During 2012, Mälarenergi Elnät AB had a total electrical network loss (both medium and low voltage network losses included) of three to four percent of their total distributed electrical volume. Converting this energy volume into a monetary figure this accounts for a loss of around 30 million Swedish crowns.

On a request from the water sewage plant Gryaab in Gothenburg a power quality survey was performed. The voltages and currents have continuously been sampled in the incoming 10 kV substation HSP01 from April-August 2008. Power quality measurements were also performed in Gryaabs other 10 kV substation HSP04 fed from HSP01 and at the terminals of the induction motor IN_PU4040 of 1.3 MW which controls one of the four large inflow pumps to the plant. The reason for the latter measurement was due to registered negative transients each time the motor was connected to the grid. The cause of the transients could be explained by the coupling in the substation, the ageing of the motor which could result in damage of the bearings or resonance in the motor circuit which amplifies high frequency harmonics.

The aim and goal of this work has been to design and implement a voltage reference network for a 12-bit PSAADC, Parallell Successive Analog to Digital Converter. A chip containing the design has been sent away for fabrication. Because of the long processing time, no measurement data are presented. The main specifications for the voltage reference generator is to generate stable reference voltages with low noise and a good PSRR. Efforts has also been made to minimize the power consumption..

On a request from the water sewage plant Gryaab in Gothenburg a power quality survey was performed. The voltages and currents have continuously been sampled in the incoming 10 kV substation HSP01 from April-August 2008. Power quality measurements were also performed in Gryaabs other 10 kV substation HSP04 fed from HSP01 and at the terminals of the induction motor IN_PU4040 of 1.3 MW which controls one of the four large inflow pumps to the plant. The reason for the latter measurement was due to registered negative transients each time the motor was connected to the grid. The cause of the transients could be explained by the coupling in the substation, the ageing of the motor which could result in damage of the bearings or resonance in the motor circuit which amplifies high frequency harmonics.

On a request from the water sewage plant Gryaab in Gothenburg a power quality survey was performed. The voltages and currents have continuously been sampled in the incoming 10 kV substation HSP01 from April-August 2008. Power quality measurements were also performed in Gryaabs other 10 kV substation HSP04 fed from HSP01 and at the terminals of the induction motor IN_PU4040 of 1.3 MW which controls one of the four large inflow pumps to the plant. The reason for the latter measurement was due to registered negative transients each time the motor was connected to the grid. The cause of the transients could be explained by the coupling in the substation, the ageing of the motor which could result in damage of the bearings or resonance in the motor circuit which amplifies high frequency harmonics.