AbstractIt is important to choose which spare parts to keep in stock. With the right spareparts in stock the costs for inventory and production loss will decrease. Cavalieri et al. (2008) highlights that the balance between inventory cost and production loss is underestimated.  It affects the company and must be considered before decision on purchase.The problem with spare engines is that they are all more or less critical for the production. That can be a reason for why no previous research targeting engines and classification of with engine should be kept in stock has been found.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

This thesis has been carried out in autumn 2009 at Uppsala University for Boliden Mineral AB. Physical modelling has been used to model a comminution circuit. The model has then been linked to a PLC.When a concentrator is about to become operational Boliden Mineral AB have been looking for a way to test the PLC. The purpose of this report has therefore been to develop models for the subprocess in a concentrator and link these models to the PLC. The subprocess was a comminution circuit in Aitik36.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

This thesis has been conducted at Saab Bofors Dynamics AB. The purpose was to investigate if a non-linear missile model could be stabilized when the optimal control signal is computed considering constraints on the control input. This is particularly interesting because the missile is controlled with rudders that have physical bounds. This strategy is called Model Predictive Control. Simulations are conducted to compare this strategy with others; firstly simulations with step responses and secondly simulations when the missile is supposed to hit a moving target.

The environmental debate is more intensive than ever before and the demands on companies increase. There are a number of methods to make it easier for the companies to fulfil the demands. Life Cycle Assessment (LCA) end ecodesign are some of the methods that can be used. Syntronic AB has the possibility to reduce the products´ environmental impact in the design phase. Therefore it is important for the company to make it possible to visualize the negative environmental impacts a product can cause in an easy way. It is also important to visualize for there clients if any improvement is possible. The purpose of this thesis is to develop a simplified model.

This thesis intends to analyse conditions for a successful implementation of consociational democracy, as a democratic model in Afghanistan. The lack of critical reviews regarding the democratisation-process in Afghanistan initiated the purpose of this study.Lijpharts democracy model was used as the basis in the comparative study. Along with empirical evidence regarding how the complex process of democracy in Afghanistan is progressing, the study investigated whether the identified conditions occurred or not.The choice of which democracy model to use can be crucial for the democratic possibilities to even survive and become established in conflict-affected communities. The principle of consociational democracy is that it is an empirically based normative model that aims to organise the state in a way that works against the risks of majority domination and oppression against the minority.The empirical case study revealed that a majority of the conditions were not met, which then can counteract the possibilities for consociational democracy in Afghanistan. The study has critically examined the prospects for the success of consociational democracy in Afghanistan, and it can be assessed that there is a limited probability for a successful applying of this model..

From 1710 to 1713 the plague raged through the Swedish province of Scania. Other studies have been made on how the disease affected the society during the epidemic. This study tries to focus on the recovery afterwards. How did the population and the farmsteads recover after the plague? Statistics from parish registers and cameral records show interesting patterns in the demography, and that the recovery was far from complete 1720.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

Allt större och större andel företag väljer att presentera och förmedla varor och tjänster via e-handel. En viktig aspekt vid e-handel är att kunden känner förtroende för e-handelsapplikationen och företaget. Denna rapport redogör för vilken inverkan multimediala inslag har för förtroendet av en e-handelsapplikation, vid initialt användande. En undersökning har genomförts med hjälp av en kooperativ utvärdering av fyra e-handelsapplikationer vilka innehåller olika typer av multimediala inslag har.Resultatet av undersökningen visar att multimediala inslag inverkar positivt på förtroendet för e-handelsapplikationer. Däremot finns indikationer på att för hög grad av multimedialt inslag inverkar negativt på förtroendet för e-handelsapplikationer..

This thesis work is the last part of the Master of Science education inmechanical engineering at KTH, Stockholm.The aim of this project was the development of a Multi-zone modelfor NOxformation in Diesel engines. Because of the stringent emissionlegislations, great effort is made to decrease the fuel consumption and theharmful emissions of internal combustion engines. Computer simulationsplay a decisive role in this context because they substitute the expensiveand time-consuming laboratory tests.The model is based on a multi-zone approach and uses the wellknownExtended Zeldovich Mechanism which gives a relation to calculatethe NO formation rate using the concentration of different gas speciesinvolved in the process.All the most important phenomena involved in the Diesel combustionhave been modelled. A special attention is then paid to the equilibriumconcentration calculation; this is a significant part of the model whichstrongly influences the following steps.A Simulink model has also been developed. This second version isbased on the previous model and it is made especially to allow theconnection with other external softwares, GT-power in this case.