ABB is one of the world?s leading engineering companies in power and automation technologiesand their solutions improve performance while lowering environmental impacts for energycompanies and industries. ABB FACTS designs equipment and plants for series and phasecompensation.This thesis has been performed at ABB FACTS on the Mechanical Design (DM) department inVästerås, Sweden. The purpose of the thesis was to develop and design calculations andsimulation tools for ABB FACTS?s standard series capacitor platforms.

In this master?s thesis the problem of simulating conditional Bernoulli distributed stochastic variables, given the sum, is considered. Three simulation methods are considered, namely the acceptance/rejection technique, Bondesson?s method and the Markov chain Monte Carlo method.To compare the three methods the bias and the standard deviations of the simulated variables are evaluated. The results of the simulation study shows that the Markov chain Monte Carlo method is not the best method for this type of simulation.

Heat is distributed to the district heating customers through pipes with water as a heat carrier. The district heating system is complex. To decide what is leakages from the district heating net versus what is the water consumption of the plant, is difficult. Therefore, the purpose of this master thesis is to establish a model where the district heating net?s leakages but also the water consumption of the plant can be followed daily. The project is performed at Vattenfall´s district heating power plant in Uppsala. Information is gathered through discussions, drawings of the plant and guided tours of the plant.

A Monte Carlo simulation of the ELECTRA reactor using (U,Zr)N fuel and a liquid lithium coolant is performed using the Serpent simulation code. The results show a reactor with a total reactivity coefficient of the coolant, fuel and material expansion that is strongly negative. These properties make the ELECTRA reactor a good candidate for a safe space reactor that could be used for propulsion of manned and unmanned space vehicles to Mars and other parts of our solar system..

Insecticides will be removed from Swedish forestry, at present insecticides are used to treat our seedlings to avoid them from being attacked by pine weevils. With the forthcoming ban on insecticides alternative protective measures will have to be tested. Holmen Forest Ltd has aimed to find an alternative and have developed a mechanic pine weevils protection accessory as well as a new concept on planting pipes. Studies have been conducted on the behalf of Holmen Forest Ltd to see how planting with the newly developed mechanical protectors and plant pipe stands up against the conventional methods used today. The study was conducted over a three week period. Three factors were compared regarding planting quality including i) pressure around the plant, ii) the depth the plant ended up in, iii) plant angle. Mechanical plant pipes were used in the study, and where tested like a one-handed and a two-handed pipe. The study concludes that further development is needed for the mechanic plant protector to live up to the speed and quality of conventional methods.

SMC is in the process of developing a micro simulation model. The existing micro simulation model developed at Cornell University for US data, CorSim, is one of the fundamental parts for the new micro simulation at SMC. To develop the Swedish model, Swedish data on all individuals in Sweden during 11 years are also available. These data are organized in a database. This paper describes the process of rebuilding the database to a more useful structure.

Simulation of different systems can be done using a graphical model description of the system based on block diagrams. The simulation software Matlab/Simulink offers a lot of possibilities to describe a huge number of systems, which can be linear as well as nonlinear. The simulation using Matlab/Simulink is done by integration based on different kinds of numerical methods.When nonlinear Simulink-models are simulated, it is often interesting to apply a Kalman filter to handle the noise that may occur within the process as well as corrupting the measurement. However, application of such a filter leads to an extensive time-consumption despite using fast computers. The reason is that the existing Matlab functions are not constructed for time optimal evaluation.

This report contains a study of replacing nuclear power with biofuel. The nuclear plant, OKG north of Oskarshamn in Sweden has been chosen and an extensive literature study about the nuclear plant has been implemented. The main aspect of this report is the availability of biofuels and whether it would be economically sustainable. Sweden?s most common biofuels are examined with regard to scope of use and potential.

At the plant of Sandvik do Brasil in São Paulo there is a need for improving the transport of inserts between the plant building and the stock building. The idea is to install a system with an Automated Guided Vehicle (AGV) to take care of this transportation. The purpose of this report is to present which demands there are on the system and to find the best solution according to the demands.To conclude this work a study was made of the plant and the AGV technology was examined. Several providers of AGV solutions were contacted to get information about prices and detailed solutions.The conclusion was that the most suitable system for this application is a small unit load vehicle using inductive wire as guiding system..

At the department of Electronic Warfare Assessments at the Swedish Defence Research Agency in Linköping one of the activities is modelling and simulation of the duel between a robot and a target. The aim with this Master's thesis is to develop a simulation model of an hovering helicopter. First a theoretical description of the forces and moments acting on an helicopter is given. Then the equations of motion are derived. These equations are simplified to be valid only for a hovering helicopter and the result is a mathematical model.

The predominant forestry harvesting method is based on the harvester-forwarder method, theharvester folds, branches and cuts trees, and sorts the logs into piles, while a forwarder transportsthe logs to a landing area.This master thesis work is about realization of a dynamic forwarder simulation model, and itspurpose is to provide an integrated forwarder simulation model in MATLAB/SimMechanicswhere the forwarder is based on a concept using pendulum arms to connect wheels and chassis.Active suspension control is developed and implemented into the simulation model, and finallycompared in simulation with passive suspension.In a first step, an integrated forwarder simulation model is developed, containing a simplifiedforwarder model, a tire-to-ground interaction model and a test track model. The simplifiedforwarder model is based a rigid multi-body system with a spring-damper suspension of thependulum arms. The tire-to-ground interaction model calculates the reaction forces, friction fromthe ground and applies the propulsion force. The test track model is a simplified version of thereal test track in Skogforsk. The propulsion wheel torque control is used to regulate theforwarder speed.

In today?s society climate change has grown to one of the largest global issues. To reduce emissions of greenhouse gases, large changes of the energy system are required. An increasingly popular solution is investments in local production of renewable energy resources like wind, solar or geothermal power. The following report examines the possibility for implementing a solar power plant on the new hospital Nya Karolinska Solna. Two different technologies for extraction of solar energy has been studied, solar thermal collectors  to meet the need of heating and solar cells to satisfy the need for electricity linked to operating the hospital building.

A piezoelectric injector was modeled, in this Master Thesis Project which was carried out at Scania CV AB in Södertälje, in GT-Fuel. GT-Fuel is simulation program from Gamma Technology.The simulation model for the piezo injector was divided into a hydro-mechanical system and an electrical system (Piezoelectric element). First the hydro-mechanic model was duplicated from Advance Continuous Simulation Language model (ACSL). The simulation results were then compared to the ACSL, to verify that the hydro-mechanical system was modeled correctly. The simulation results for the electrical model were also compared with a Simulink model.

ITT Flygt is a world leading company that mainly manufactures submersible pumps. A problem of ITT Flygt is that product development projects rarely manage to hold the estimated project time. It shows that something unexpected occurs in projects quite often, which results in delays. The delays can both be due to an optimistic time plan of projects and risks in product development projects which are not discovered at an early stage. This added with unforeseen delays makes it difficult for ITT Flygt to estimate the duration of their projects.The goal with the Master thesis is to examine a suitable method for simulation of project time.

This thesis of 15 hp has been implemented at Halmstad University, in collaboration with Saab Dynamics in Linköping. Saab Dynamics is a company operating in the defence industry where competition is tough. This necessitates new ways to increase efficiency in the company, which is the basis for this thesis. Saab Dynamics wants to introduce simulation driven design. Since Saab Dynamics engineers have little experience of simulation, required a user methodology with clear guidelines.