This report is commissioned by the Water and Sewage Agency in The City of Mariehamn, Åland. The basic aim is to investigate positive or negative effects of a relocation of the sewage Pipe from a wastewater treatment plant, Lotsbroverket. The environmental licence of Lotsbroverket is to be revised and The Environmental Appeal Board at Åland?s Government and Administrative Board has made demands that several possible locations in an outer water area should be examined. The present location of the sewage Pipe is in Svibyviken, which has been classified as an ?inner water area?.The objective of this work is to study to which extent the nutrient loading from Lotsbroverket influence the environmental conditions in Svibyviken, and to investigate the suitability of different locations of the wastewater Pipe from Lotsbroverket.The way a coastal area looks, i.e., its morphometry, determines to a large extent its ecological characteristics.

The master thesis, conducted at Metrima AB, concerns the development of a non-intrusivedistribution meter as a basis for individual tap water billing in apartments.The project is conducted in response to the market interest in individual tap water billing inapartments as an answer to environmental concerns regarding water consumption. Due to thehigh installation cost of traditional water meters, a new method of determining waterconsumption, without having to cut water Pipes, is proposed.The proposed method distributes the total water consumption for an apartment complex toindividual apartments according to distribution meters, measuring water run-time, in eachapartment. The water run-time is estimated by measuring the water Pipe?s outward vibrationsand temperature changes.A test environment was established and a prototype built, using a tilt- and vibration sensor forvibration sensing and a precision temperature sensor to measure temperature changes. As bothsensors work well in the test environment, further testing was done in 3 apartments for aduration of 5 days.

This work is a part of the project ?Våtmarker i odlingslandskapet ? uppföljning av miljömålen? (Wetlands in arable land ? following-up of the environmental goals). The main objective with this project is to study nitrogen and phosphorus retention in a constructed wetland by using mass balance calculations. Continuous measurements of nutrients and water flow through the inlet and the outlet of the wetland are made. However, substantial amounts of nitrogen and phosphorus were assumed to reach the wetland with a drain-Pipe transporting wastewater from nearby houses (10 persons).

More frequent and intensified rainfalls are expected to occur due to climate change in the nearfuture. This together with a higher proportion of paved areas increases the pressure on today?sstorm water systems (Risinger, 2014; Boverket, 2013; Stahre, 2006). Traditional storm watersystems (i.e. underground Pipe systems) have during last decades started to be questioned(Olshammar & Baresel, 2012).

More frequent and intensified rainfalls are expected to occur due to climate change in the nearfuture. This together with a higher proportion of paved areas increases the pressure on today?sstorm water systems (Risinger, 2014; Boverket, 2013; Stahre, 2006). Traditional storm watersystems (i.e. underground Pipe systems) have during last decades started to be questioned(Olshammar & Baresel, 2012).

In this report focus is put on the combustion process at a cement plant. Combustion is the heart of the cement making process and absolutely crucial to have under full control and well optimized. The fuel is put into the process through a burner Pipe and this burner Pipe is modified to reach a more efficient combustion. The primary target is to enable burning of heterogeneous alternative fuels and increase the production level. Other positive effects from this type of optimization is lowered specific fuel consumption and lowered CO2 emissions. A redundant burner is chosen for the project and overall the project steps are the following: 1. Installing a Jet air nozzle ring in a way so it can move both axially and radially due to temperature changes. 2.

Denna studie visar hur valet av metod och värderarens antagande påverkar värderingen avbyggrätter. Inledningsvis studeras ett antal faktiska värderingar med avseende på användametoder och antaganden. Vi finner att fastighetsvärderarna i regel använder ortsprismetodenvid värdering av byggrätter, som komplement används ibland en kalkylbaserad metod. Detvisas att fastighetsvärderarens antaganden om framtida bebyggelse i hög grad påverkarvärderingen. I mindre utsträckning påverkar valet av värderingsmodell..

For Skattkärr IF a turf field with warming has been projected to increase field?s utilization hours and to have a longer period for athletes to perform their activities outdoors. The technique chosen to heat the plan is a type of a geothermal heating system without a heat pump. The brine, which is water with 30% ethanol, collects heat from the borehole and discharges it to a coil in the field. There is at position 11 boreholes but it is planned to increase the number to 31, which is the design for the facility.

Drain water heat recovery is an uncommon measure in multi-unit residential buildings. There istechnology available for the purpose but the knowing and experience of the heat recovery systems islittle. The purpose of this thesis is to evaluate the future potential of drain water heat recovery inmulti-unit residential buildings.A major part of the multi-unit residential buildings in Sweden were built during modernismen andrekordåren (1940?1975). Many of the buildings have worn out drain and water supply systems andmany are in need of a general refurbishment.

This thesis aims at determining the heat losses in a property vent stack and its roof valve. Upon request of a company, the vent stack is analysed for possible heat recovering solutions to be implemented, while relining of the drain system is executed and with a suitable payback time for the economic investments. The heat loss calculations are based on data for properties that are located in the Stockholm region, but also easy to change depending on the situation. The calculations are done on Pipes made out of cast iron, which still is the most common type of drain Pipe in Sweden, and these are the Pipes that relining is usually made on. The calculations that needed to take several variables into account have been done in MatlabR2014a and the thermos dynamical properties that were used in those calculations have been extracted from EES.Three different types of heat losses in the vent stack have been taken into consideration in this thesis.

Today there is no way of measuring or simulating turbulent flow in high Reynolds numberenvironments. The computational power required to simulate these conditions is not expectedto be available for several decades so instead the CICLoPE project aims at solving thisshortage by the construction of a long carbon fiber wind tunnel in which real measurementscan be made. To do accurate measurements it is of importance that the wind tunnel, 0.9 metersin diameter and 110 meters long, is as straight as possible.This master thesis treat the design and construction of a device which may be used to align thetunnel along a reference laser beam. A design is presented which allows the Pipe to be alignedwithin about a quarter of a millimeter along its entire length. Contents span over severalscience fields such as physics, mechanics, control theory and electronics.The result is a theoretically correct design.

Guazuigua is a small village in Bolivia, which has had too small water resources, especially for irrigation. A project started after some studies were made, to create a canal to provide the village with water from a nearby town. To make the canal work it had to cross a dried out river. There have been several attempts to cross these dried out rivers, but with poor results. The purpose of the report is to provide a solution for this problem.

Thermal fatigue is a serious problem in todays power plants. A large amount of damages around the world circles around that subject. The damage can come from the mechanism of two flows mixing with different temperatures in a T-junction. It is a fundamental prerequisite that these T-junctions are frequently tested for damages. An amount of criterias steers the rate of testings.

This report describes the development process of a Pipe clamp used on exhaust system for cars. It is made based on the manufacturers desire to improve and make the clamp easier to manufacture and to reduce its price to their customers. This should be done either by manufacturing the clamp in one piece without an expensive and work intensive welding process, or by generating ideas of how to develop a brand new type of clamp. Investigating the market for similar products was done to eliminate intrusion of other manufacturers? patents but also to generate ideas.

The aim of my thesis is to obtain knowledge of textile wastewater and textile sludge from an environmental perspective, which can be used as a basis for the  ?Sweden Textile Water Initiative? guidelines for a sustainable sludge management. In my study I have mainly focused on textile dyes, salts and metals and their routes during wastewater treatment.This paper is partly a literature review, which I began by identifying the pollutants discharged from each textile process. Then I studied wastewater and sludge quality, environmental aspects, possible treatment and recycling methods. I have also tried to find existing type of guidelines in order to make comparisons.