The City of Stockholm has decided to invest in renewable energy and especially in photovoltaics. The objective of this thesis is to investigate the photovoltaic potential on roof areas that the city possesses and to further investigate some buildings of the Property Management Department. The thesis also compares some existing photovoltaic plants with the solar irradiance map which shows available roof area on each building in Stockholm. The report ends with a literature study about the climate impact and greenhouse gas emissions of photovoltaic.The total available roof area suitable for photovoltaic plants is estimated to 700 000 m2, with a potential electricity production of 110 GWh per year. This corresponds to 17 % of the City of Stockholm?s yearly electricity consumption.

Housing construction very close to the lake Mälaren has become very popular today. One potential problem with these houses is the influence of the sea climate. Unprotected buildings are affected by strong winds and precipitation. So for that reason, it is very important to make an accurate climate investigation and use it for decision-making during the planning of the new settlement.It is very important with a good moisture protection regarding pelting rain, that is the combination of wind and rain. This is more important for buildings close to a lake, as this location normally means a higher exposure to wind.

Cows are ruminants and they need fibers in their feed and sufficient eating time to function psychologically and physiologically. Many of our cows don?t get enough forage and too much concentrates, which given in the wrong way may cause health and behavior problems. Too much concentrates at once makes the pH in the rumen sink and this may cause decreased fiber utilization since the microbes in the rumen are negatively affected by this. The cow may also get serious problems such as laminitis and abomasal dislocation.

Det här kandidatarbetet kommer framförallt att beröra filmtekniken, Matte Painting, men vi kommer även röra oss runt omkring ämnet och presentera andra delar från filmproduktionen och framförallt postproduktionen för att lättare kunna sätta Matte Painting i ett relevant sammanhang. Vi jämför Matte Painting med en teaterkuliss, en bakgrund som på nära håll eller ses från fel vinkel kan bryta illusionen av att det är en verklig miljö. Vi undersöker och presenterar hur man kan bygga upp en digitalt skapad Matte Painting som möjliggör att inte behöva åka land och rike runt efter den idealiska filmplatsen, utan kan spela in filmscenen i en studiomiljö. Vi analyserar existerande filmscener som har använt sig av Matte Painting, gör jämförelser mellan olika användningsområden för Matte Painting samt diskuterar fram en slutsats som besvarar vår frågeställning: ?Hur har utvecklingen av filmtekniken, Matte Painting, sett ut och hur kan man tillämpa en digital Matte Paint i postproduktion för att förstärka helhetsupplevelsen av en filmscen?? --- This thesis will primarily concern the film technique, Matte Painting, but we will also roam around the subject and introduce other elements of the film production, and above all post production for ease of putting Matte Painting in a relevant context. We compare Matte Painting with a theatrical backdrop, a background that closely or viewed from the wrong angle can break the illusion that it is a real world environment. We will investigate and present how to build a digitally created Matte Painting that enables not having to travel across the country for the ideal film location, but can shoot the scene in a studio environment. We analyze existing film scenes that have made use of Matte Painting, making comparisons between different uses for Matte painting and discuss a conclusion that answers our main question: "How has the evolution of the film technology, Matte Painting, looked like and how you can apply a digital matte paint in post production to enhance the overall experience of a movie scene?".

AB Sandvik Cormorant?s production unit in Gimo has identified a need to examinethe handling of products between operations with the purpose of generatingproposals of improvement for the product handling.The aim of this project is to study the existing manufacturing process and givesuggestions for improvement. The proposals should reduce the manual handling ofproducts, decrease the risk of damaging the products during the manufacturing andform a basis for increased traceability. Based on a mapping of the manufacturingprocess and the problem description, a specification of requirements has beencomposed.The mapping of the manufacturing process suggests that a change of the currentsystem is required. The company is recommended to decide how the producthandling between operations should be performed as guidelines for the productionteam.

De senaste fem åren har tågresandet ökat med 28 procent. Den ökade trafiken har lett till ett högt utnyttjande av anläggningar och fordon. Det har i sin tur medfört stora problem med punktligheten av tågtrafiken. För att matcha den ökande trafiken på Sveriges järnvägar ska detta examensarbete undersöka om man kan implementera Lean produktion för Banverkets byte av spårväxlar för att göra dessa mer effektiva. För att ta reda på vad Lean produktion egentligen är gjordes en litteraturstudie.

Cooling down the indoor air can be done in several ways. One way is desiccantcooling which will be used at the Stockholm Arena. This method is used in airhandling units that use temperature changes and moisture fluctuations in the air. Oneof the steps is to add heat during the cooling process in order to reduce the relativehumidity of the exhaust air. The air passes thru an adsorptions rotor which thenabsorbs moisture from the supply air.

The emergency medical care in Sweden has been under persistent debate, due to factors such as long waiting hours, inefficient patient flow, and understaffed departments. In an effort to meet the critique and with a willingness to improve the problems, an increasing amount of emergency clinics are adopting theories and models within Lean. Positive outcomes are evident, there has been some criticism directed towards Lean. Among these is the argument that in order for Lean to be successful it needs to be used within standardized and foreseeable processes, and that it therefore only is applicable to those kind of processes found within industrial production. This prompted the question of whether Lean was a suitable strategy within emergency medical care, considering the large variation of patients and non-foreseeable processes that in fact share little resemblance to that of industrial production.

I contacted the production company Salmonfox in the hope that they would have any projects that they needed help with. It showed that Salmonfox just started up an old project that they needed to complete. They wanted my help to edit some trailers and one crowdfundingfilm for the short film called, Captain Sweden (Kapten Sverige). Salmonfox are hopefully going to use the different trailers and crowdfundingfilm to promote the short film and get help with the funding to make a feature. The project began with a pilot study in which I made a time plan and a requirements plan, where the different requirements were set.

Sheep production is the only animal production in Sweden that is increasing. Therefore,increasing knowledge of the production is of great interest. In order to run a viable sheepproduction, producers needs to be successful in the breeding of the animals and achievean economic surplus in the end. Lambs that are born healthy and vital have greaterconditions to perform high lamb weight gains and thus a successful production. Thereare many factors affect the survival, birth weight and early weight gain of the new bornlamb.

The purpose of this master thesis is to investigate different types of measures for making buildings more energy efficient and to estimate their profitability. The calculations were performed with the building simulation program VIP+ and the evaluation of the profitability with the life cycle cost method. Furthermore, it was examined how losses in the distribution of secondary systems of district heating can be avoided. Options to replace district heating with a local district heating system based on bio-energy have been investigated. The possibilities of achieving more efficient thermal energy consumption and production for the chosen estate were also examined.The object of the study has been a residential estate with 133 detached houses in Uppsala, built in 1974.

SUMMARYInventory of raw materials holds an important role in companies within the manufacturingsector. The inventory works as a buffer that secure the supply of materials to the productionunit. The aim of the inventory is to ensure that the company is able to meet the customers?demands despite fluctuations and variations in the material flow. The size of the warehouseand the layout are physical limitations for the quantity of articles that can be stored.

Ask any constructional worker and there is a high probability that this person knows a colleague with pain or other disorders caused by working with power tools.According to the Swedish Work Environment Authority 71 percent of the Swedish constructional workers is exposed to vibrations at least 25 percent of the working hours. Despite this, the number of reported occupational sicknesses caused by vibrations is as low as 1, 4 percent.JM Ltd. is one of the largest constructional companies in Sweden. Their main business is new housing and development of residential areas. God quality and low impact on the environment is a part of great importance in the company?s long-term goals.

Sheep production is the only animal production in Sweden that is increasing. Therefore,increasing knowledge of the production is of great interest. In order to run a viable sheepproduction, producers needs to be successful in the breeding of the animals and achievean economic surplus in the end. Lambs that are born healthy and vital have greaterconditions to perform high lamb weight gains and thus a successful production. Thereare many factors affect the survival, birth weight and early weight gain of the new bornlamb.

SUMMARYInventory of raw materials holds an important role in companies within the manufacturingsector. The inventory works as a buffer that secure the supply of materials to the productionunit. The aim of the inventory is to ensure that the company is able to meet the customers?demands despite fluctuations and variations in the material flow. The size of the warehouseand the layout are physical limitations for the quantity of articles that can be stored.