The viscosity of air buildings is a hot topic within the construction performers, which the industry feel they have too little knowledge about. This study is mainly aimed against air density in apartment buildings and airflow measurement. The study consists of a theoretical reference, educational visit, interviews and a survey conducted among construction workers at Magistratshagen in Linkoping.Earlier requirement in terms of air leakage through the climate screen was removed and today there are only energy requirement for a dwelling in Boverkets Building Regulations. The difference between a passive and a typical air tight construction is that the passive house have a maximum requirement of 0.3 l /s m2 of air leakage through the building climate screen. The requirement imposed on passive houses is to minimize the supply of power and energy for heating the building.Air tight constructions have heavy demands on the performance and accuracy of everyone involved with the project. The client must specify their requirements and also be prepared to pay for any additional costs. The architect and building planners have to design the building with regard to air tightness. Finally, the construction workers are required to do a careful work in order to get all the connections in the building air tight.The study suggests that an air tight building is a closed system where no forced ventilation exists. There are no reasons not to build too tight as long as there is a functioning ventilation. In this study the authors ask themselves how an air tight building changes over time. No theoretical information has been found on these changes, but the respondents assume that air density decreases with time. The deterioration is mainly assumed to be caused by construction materials changes over time. The study shows that construction workers knowledge of air tight construction is mixed, which they themselves admit in the survey..

Cooling down the indoor air can be done in several ways. One way is desiccantcooling which will be used at the Stockholm Arena. This method is used in airhandling units that use temperature changes and moisture fluctuations in the air. Oneof the steps is to add heat during the cooling process in order to reduce the relativehumidity of the exhaust air. The air passes thru an adsorptions rotor which thenabsorbs moisture from the supply air.

The industrial sector accounts for a large share of greenhouse gas emissions. To reduce its negative impact on the environment is crucial in the quest for a sustainable future. In discussions of the industrial sector's impact on the environment guidelines have been highlighted as a tool to assist the industries in their efforts to change the relationship between the consumption of energy and production. This by improving energy efficiency and a shift to the best available technology. During the past 30 years the steel industry has reduced its energy consumption per ton of steel produced by 50 percent.

This thesis is based on a market survey sent to the passive members of Södra skogsägarna within the scope of practice of Vimmerby. A member of Södra skogsägarna is considered passive if the member not has delivered timber to the association during the past five years. The purpose of this thesis was to obtain as much information as possible about the forest owners, to be able to interpret why the member did not choose to deliver their timber to the association. The survey was worked out in close collaboration with Södra skogsägarna to answer this question. The responses indicate that economic returns are important to the individual landowner. The price of timber is most important in a timber business and the majority of forest owners want to have a personal meeting if you can choose how you wish to be contacted by the inspector.

The predominant forestry harvesting method is based on the harvester-forwarder method, theharvester folds, branches and cuts trees, and sorts the logs into piles, while a forwarder transportsthe logs to a landing area.This master thesis work is about realization of a dynamic forwarder simulation model, and itspurpose is to provide an integrated forwarder simulation model in MATLAB/SimMechanicswhere the forwarder is based on a concept using pendulum arms to connect wheels and chassis.Active suspension control is developed and implemented into the simulation model, and finallycompared in simulation with passive suspension.In a first step, an integrated forwarder simulation model is developed, containing a simplifiedforwarder model, a tire-to-ground interaction model and a test track model. The simplifiedforwarder model is based a rigid multi-body system with a spring-damper suspension of thependulum arms. The tire-to-ground interaction model calculates the reaction forces, friction fromthe ground and applies the propulsion force. The test track model is a simplified version of thereal test track in Skogforsk. The propulsion wheel torque control is used to regulate theforwarder speed.

We are heading towards a huge switch of how energy is produced with fossil fuels being replaced by renewable energy sources. It is not difficult to replace the energy you use in the house and there is no need for futuristic technology. There are already many established products on the market such as high efficiency vacuum solar collectors, heat pumps & small wind power stations that can supply the energy being used in a house. The company Sol & Energiteknik SE AB in Huskvarna has many different products which can reduce the need for an outside energy distributor. An average house in Sweden uses 15 000 kWh for heating, 5000 kWh for tap water and 5000 kWh for electricity.

The Swedish building and property management sector are responsible for about 30 % of the total energy use. In order to take environmental consideration, different environmental assessment tools and standards are used. Miljo?byggnad, Svanen, FEBY12 and PHI are some of these. There has been increased interest to certify buildings and therefore it is of interest to evaluate the assessment of the energy field to see if relevant energy aspects are assessed.

Climate change is the modern society?s common issue. The developed countries areconsuming more than what is sustainable, and the climate change due to the use offossil fuels can be seen clearly. EU has specified goals, in order to stop furtherdamage, which demand that every member state have to reduce its energyconsumption by 20 % before 2020 and 50 % before 2050, relative to 1995.The Swedish government uses a number of instruments to encourage reduction in theusage of energy, but every individual has to contribute to reach the goals.With increasing energy price the cost of living is going up. A lot of people are lookingfor ways to save energy and not be affected as much by the increasing price.Investments for insulation, replacement of windows and replacing old heating systemfor a new efficient heat pump is getting more and more common.This thesis is about investigating the possibilities in becoming independent from buyingenergy for households.

AbstractElectricity consumption is a globally increasing problem caused by the high share of electricity produced in coal power plants. These contribute to high carbon emissions when only about 1/3 of the heat generate electricity and the remaining 2/3 of the heat cools off. Combined heat and power plants (CHP) have high efficiency because they use the residual heat for domestic heating. The CHP plant often use fuels from renewable resources, giving them a lower carbon footprint, but are also depending on the heat demand. If electric powered products such as drying cabinets convert to heat powered products more environmentally friendly electricity will be produced by CHP plants, which can supplant electricity, produced from coal power plants and reduce carbon emissions.

The municipality, of Gatukontoret in Local government of Borås has in the long run, a required need to look after the current heating devices (the gas production plant) in sewage treatment plant, called Gässlösa. The practical work of the examination is about, trying to find a better way to take care of the current heat recovery. That may be one way or another, rather easy to implement in the existent construction.Through the work to increase the efficiency of the gas engine, implement of some external cooling system by heating exchange device. That gives an opportunity to heat (primary) the digester, (but even all internal public areas) with its own superfluous heating.The report shows that if the management group may invest 422 704 crown to implement a heat exchanging device, it gives more space to reduce the need to buy expensive external energy. Gatukontoret´s pay off time, for buying machines, is 20 years, with reservation to calculate with 4 percent internal interest, leads to the yearly mount of 31103 crowns.If Gässlösa increases the gas engine time in (effective) duty approximately (correspondingly) 48 hours a month the entire investment will generate a profit in January in year seven after the implementations.

Stockholms vattenskärning AB in Kungsängen has through the acquisition of a company begun to design and produce aircraft heaters whose origin is early 1970s which follows a high inefficiency in terms of energy consumption and size.The aircraft heater, which is sold worldwide, serves its purpose for customer satisfaction and has done so ever since it was developed in the 70s.Stockholms vattenskärning AB is now investigating the possibility in making the aircraft heaters more efficient, both in terms of energy consumption but also on a more efficient design with the belief that it would lead them to an edge in the market. The aircraft heater consists of several main components whose function altogether is to keep passenger aircrafts warm while they are on the ground.This project has been limited to the further development of the heat exchanger package which accounts for the conversion of the hot medium to the fresh air being carried in to the aircraft cabin. Work has been divided into different phases in order to create a better understanding of the project range and to make it easier to divide the various elements in the time available, 10 weeks. These phases are literature review, situation analysis, concept generation, CAD, concept comparison and writing reports.After the initial literature review was made, a fundamental theory was written which is essential in understanding the remaining parts of the project.With the theoretical part as support, measurements and calculations were made on the current heat exchange package in a situation analysis to ensure its operation and efficiency.In the concept generation phase, the collected facts from the literature review was used as the basis for creating a matrix. The purpose of the matrix was to indicate the two most suitable types of heat exchangers to develop four new concepts out of.In the CAD phase the four concepts was drawn up and then described with text and images.The last phase is the concept comparison where a concept selection matrix is used to function as a decision basis for further production at Stockholms vattenskärning AB. The four concepts have been developed based on the current heat exchanger and is gradually changed into a design of a cross-flow heat exchanger constructed out of stainless sections. The purpose of this is to have gradual upgrading of the heat exchanger as an option, in order not to saturate the market..

A Swedish electronics company wants to make the cooling of one of their electronic components more efficient. They propose that a retrofit liquid cooler is the way to achieve this goal. The current air cooling has high energy cost due to the high amount of power needed to power fans and heat exchangers. Using high volumes of air for cooling also leads to noise pollution. The conversion from air to liquid cooling would possibly make the operation of the electronics more cost efficient and less noisy.The purpose of this project is to theoretically evaluate different concepts of drawing the heat generated by the electronic component in to a fluid, using numerical calculations in Matlab and FEM simulations in ANSYS.

This report treats whether it is viable to invest in solar heating to heat the therapy pool at Östersunds Rehabcentrum. The rehab center is owned by the county council of Jämtland and is located on Solliden in Östersund city. The solar heating where supposed to be a complement to the district heating that was heating the pool in the current situation. Later, it however showed that this was not the case. The pool is currently being heated by a radiator circuit that is being heated by the district heating.

In cooperate with Asko Cylinda we have developed a new heat system too short the process time and reduce the energy consume in a dishwasher and still have it too be a class AAA. The environment and quality is important for the company too still be the number one on the market, If they want too keep that position the product developed of new innovations will be very important. The systems we have developed are more effective and reduce energy up too 25 %. The process time is reduced too less than two hours, from the today two and half-hour. The solutions are too heat up the rinse water and the dishwater at the same time, with a new heating system and it make are solutions unique and effective. Its good for the dish and the environment.

We have the tradition in Sweden to build villas and houses with a wooden framework. It has become natural for us because we have so much forest in our country. Building with wood has advantages, it is easy to process, but also disadvantages, as it is sensitive to moisture.Finland has long made use of the thermal blocks to build villas. It is a type of bricks that are a bit like a sandwich element, with a core of EPS and concrete on both sides of the core material. The concrete is hollow, so that after the walls has been bricked up you pour concrete into the hollow bricks.The issue of this report is to find out if concrete can be an alternative to wood as framework material in villas.