The purpose of this work is to design and construct a device able to measure the mechanical attrition of oxygen carrier Particles. Those particles are used in chemical looping combustion and in the present situation there is a lack of knowledge in how the attrition process work and in which extension. To find already tested solutions trying to answering this problem a literature study wascarried out and the best solution found was the so called Grace-Davison Jet-Cup method. This method is supposed to emulate the attrition caused by a cyclone separator and its advantages are that it is possible to use small test amounts, 5-10 g, and a thirty minutes long test will be enough to acquire useable results. An device was designed based on the Jet-Cup method with some slight modifications.

Today, our cows experience a harder pressure to achieve higher milk yield. To manage this challenge the animal needs first class feeding and treatment. An important aspect of the feeding is to fulfil the need from the cows of especially fiber; and fiber with a sufficient proportion of long Particles. Both too much and too little fiber is bad for the wellbeing of the cow, and she might get diseases like acidosis. Many models for feed management have been developed to secure that the animal gets enough of e.g. fiber with a sufficient proportion of long Particles.

The purpose of this work is to design and construct a device able to measure the mechanical attrition of oxygen carrier Particles. Those particles are used in chemical looping combustion and in the present situation there is a lack of knowledge in how the attrition process work and in which extension. To find already tested solutions trying to answering this problem a literature study wascarried out and the best solution found was the so called Grace-Davison Jet-Cup method. This method is supposed to emulate the attrition caused by a cyclone separator and its advantages are that it is possible to use small test amounts, 5-10 g, and a thirty minutes long test will be enough to acquire useable results. An device was designed based on the Jet-Cup method with some slight modifications.

Cycling is one of the most sustainable transport modes available and it is widely promoted inmany urban areas. The health benefits from cycling has shown to be substantial, includingdecreased risks of diseases related to overweight and enhancing brain capacity. However, inurban areas cyclists can temporaly be exposed to high levels of air pollution, resulting inhealth risks as opposed to health benefits.The objective of this thesis is to develop a rasterbased test model in GIS that estimates theinhaled dose of air pollution for cyclists based on relative particle concentration in differenttransportation micro-environments. The method used is a least-cost path approach,calculating three different routes; shortest, fastest and least dose for four different trips withinSödermalm, Stockholm.The results show that the inhaled particle dose can be greatly reduced, 39% - 58% for three ofthe routes, by choosing the least dose route. One of the most interesting findings is thesubstantial increase of dose when high levels of particles are combined with uphill cycling.The conclusion for the thesis is that a raster-GIS model can be very useful for estimating doseof different air pollution particles and chemicals along cycling routes.

With a growing population on earth the amount of end-of-life vehicles (ELVs) and other scrap steel increases. The European Directive 2000/53/CE? requires a minimum of 95 % reuse and recovery and 85 % re-use and recycling no later than 1 January 2015, for end-of life vehicles. This imposes a need for more efficient recycling and recovery. Despite this shredder residue (SR) is commonly land filled.This report investigated the magnetic fines residue generated at Stena Metall shredder facility in Halmstad, Sweden.

In an attempt to develop a more cost-efficient material for solar   energy applications, nano-particles of nickel oxide composite in a silikatmatris manufactured with solar gelmethod and studied structurally by electron microscopy. Furthermore, the thin film optical properties characterized by Variable. Angel Spectroscopic Ellipsometry. Sol gelfilms suitability as a selective absorber surface is also analyzed by optical modeling..

With a growing population on earth the amount of end-of-life vehicles (ELVs) and other scrap steel increases. The European Directive 2000/53/CE? requires a minimum of 95 % reuse and recovery and 85 % re-use and recycling no later than 1 January 2015, for end-of life vehicles. This imposes a need for more efficient recycling and recovery. Despite this shredder residue (SR) is commonly land filled.This report investigated the magnetic fines residue generated at Stena Metall shredder facility in Halmstad, Sweden.

The purpose of this work is to design and construct a device able to measure the mechanical attrition of oxygen carrier Particles. Those particles are used in chemical looping combustion and in the present situation there is a lack of knowledge in how the attrition process work and in which extension. To find already tested solutions trying to answering this problem a literature study wascarried out and the best solution found was the so called Grace-Davison Jet-Cup method. This method is supposed to emulate the attrition caused by a cyclone separator and its advantages are that it is possible to use small test amounts, 5-10 g, and a thirty minutes long test will be enough to acquire useable results. An device was designed based on the Jet-Cup method with some slight modifications.

Fieldstudys on 22 farms (23 silos) to study relationships between the actual particle size of the maize silage and the theoretical length of cut. The measure of theoretical length of cut were stated by the farmers and not measured by us. Particle size of maize silage was determined using the New Penn State Forage Particle Separator. SLU Skara made a special sieve for us, that had larger holes than de original sieves. The samples were shaken after instructions and then the material was weighted. We have also been taking out samples for microbiological analyses from the silos on 13 of the farms.

The thesis evaluates a new kind of bearing arrangement in a traction motor that ABB hasdeveloped. Since the arrangement is designed in a new and innovative way it needs to beevaluated to see if it is safe to use. In today?s traction motors, bearings with a big internalclearance (C4-clearance) are used. The basic idea of the new arrangement is to reduce the fitsbetween the bearing and shaft/house.

This work reveals the results of BAL performed on horses included in a larger study that assessed the relationship of amount and type of inhaled particles in equine stable air on indices of respiratory inflammation in horses and people. During this study an unanticipated and marked elevation in lung eosinophils was detected in a number of the horses. The possible significance and cause of this pulmonary eosinophilia was investigated further, and is the main focus of the work presented.

When investigating mechanical problems it is often more convenient to deal with scalars rather than vectors. In this project methods stemming from the field of analytical mechanics, which lets one derive the equations of motion using scalar quantities instead of vectors, have been used. Two mechanical problems were investigated, a double pendulum with a spring and particles orbit in a sphere. The equations of motion of the two systems were derived with the assistance of computer algebra, using Maple and the external package Sophia. The systems were investigated with regard to periodicity and conserved quantities..

In an attempt to develop a more cost-efficient material for solar   energy applications, nano-particles of nickel oxide composite in a silikatmatris manufactured with solar gelmethod and studied structurally by electron microscopy. Furthermore, the thin film optical properties characterized by Variable. Angel Spectroscopic Ellipsometry. Sol gelfilms suitability as a selective absorber surface is also analyzed by optical modeling..

The task was to design and manufacture a submersible displacement pump working with the wobble plate principle. The main task for the Wobble plate pump is to be used as a sewage pump for smaller households or dewatering pump in environments where small flows and high pressures are acquired. For these purposes ITT Flygt sell a screw pump, PC-Grinder 3068. The hydraulic part of the PC-Grinder is manufactured by a subcontractor. Therefore ITT Flygt wants to evaluate an alternative to their screwpump PC-Grinder, which can be entirely manufactured by them self.

When investigating mechanical problems it is often more convenient to deal with scalars rather than vectors. In this project methods stemming from the field of analytical mechanics, which lets one derive the equations of motion using scalar quantities instead of vectors, have been used. Two mechanical problems were investigated, a double pendulum with a spring and particles orbit in a sphere. The equations of motion of the two systems were derived with the assistance of computer algebra, using Maple and the external package Sophia. The systems were investigated with regard to periodicity and conserved quantities..