In Sweden, a big part of the energy use is used in the housing sector. Political goals and targets are set up which the housing sector needs to work towards. Apartment buildings are a major part of the housing sector in Sweden and therefore reduction of energy use in these kinds of buildings are key to lower the energy use in Sweden. But there are not only political incentives to reduce the energy use. Some energy?saving measures are directly profitable and should thus be performed.

Norconsult AB has developed a solarhousing concept, a house designed for the warm climate in the Middle East andwith large quantities of solar panels installed. The cooling system for the house was designed in an earlier report, the purpose of this thesis is to investigate the possibility of short and long term storage of thermal energy via an underground energy storage volume.Two different designs of the storage and three different filling materials have been integrated into a model to simulate different cases. The first design consisted of pipes installed in the ground, without insulation. The second design consisted of an insulated concrete box installed to prevent thermal energy from the surrounding soil to flow towards the lower temperature regions within the storage. The three different filling materials were dry saudi sand, water saturated saudi sand and the filling material used by the client for energy storage in Sweden.The results from the simulations show that neither of the designs, regardless of the filling material, managed to extract enough thermal energy from the house to the ground to uphold the demands of indoor climate.

SUMMARY Several studies have shown that weaning pigs are in great need of heat. The reason for this is mainly because the pigs are given very little feed just after weaning. Some of the pig producers of today have tried to get along with these problems by building some kind of hut for the pigs. Some of these pig houses have been included in this study.The study has shown shortcoming functions for the pig cottage. The expected heat increase has not occurred.

Enköping?s Rugby Club has long lacked a bigger hall to gather their members in, where they can meet and socializes outside trainings and games. Thanks to Enköping?s municipality, The Swedish Inheritance Fund, Swedish Sports Confederation, sponsors and club members the clubhouse will be built out with additional 100 square meters.The project is planned in two phases of which phase one is the buildup of the new clubhouse and phase two is the renovation of the existing part. Phase one started with the first groundbreaking in December 2006 and was finished for the season 2007.

Uppsalahem AB is a municipally owned real estate concern that owns and administrates housing for nearly 30 000 people. The company puts a lot of effort into reducing the energy use of their housing stock. This project is a master?s thesis in the energy systems programme at Uppsala University, carried out in collaboration with Uppsalahem. The aim of this thesis is to provide energy saving measures for fourteen student housing buildings in Uppsala, Sweden.

Our everyday life is becoming more active and the activities we perform influence the way we dress. Due to an increase in activities undertaken in an urban environment, demands are changing and the need for active wear that meets the new demands follow suit. The four characters represented in the research can be seen as a reflection of the functional features needed, including base layer, mid layer/insulation and shell.Despite the increase in activities, most of our clothes are still constructed on static dummies or drafted on a table in 2D and the main developments within the active sportswear field is driven by material innovation. By creating garments on a body in movement, my aim is to develop new functions and expression in active sportswear through construction.Construction methods in active sportswear are examined and understood through observations and reconstructions and constitute the foundation of a study of movement for a design recovery.The movement and features required for leading an active urban life sets the direction of the development of new func- tional garments. A series of trial and error sessions and draping fabric on a live model in movement created the prototypes used in functionality tests to establish their feasibility.

The purpose of this project is to analyze earthing systems for houses. By practical measurements and theoretical analyzes consequences of possible faults, that can occur within the facility and in the low-voltage distribution network, is illustrated.  The reason for this project is that nowadays one has to arrange with a main equipotential bonding system for buildings. Apart from that, if necessary, bathrooms must be provided with a supplementary equipotential bonding system.The practical measurements verify that potential differences in facilities may be due to voltage drops in the PEN conductor between the origin of the electrical installation and the power transformer.Based on the theoretical analyzes of possible faults, it is considered that the requirement for  supplementary equipotential bonding systems for bathrooms in most cases can be questioned, when basic insulation, fault protection, residual current devise and main equipotential bonding system already provides an adequate level of protection.A PEN conductor loss may result in a situation where metallic parts attached to the equipotential bonding system starts working as earth electrodes. Equipotential bonding system may also increase the incidence of stray currents. If TN-C-S systems is provided with a local connection to earth a redundant system against PEN conductor loss is obtained.

When constructing a building, a number of aspects must be harmonized in order for it to fulfill requirements ? a building must fulfill requirements such a load-bearing, conservation of energy and a good indoor environment by means of, among other things, moisture proofing .Moisture problems in buildings can affect health negatively. As we are increasingly staying in indoors, demands on a good indoor environment are higher.This work starts with examining moisture problems in slab-on-ground solutions, and then links the various scenarios to moisture problems in a concrete slab of a real building. The building with moisture problems is located in Årby by in Borlänge and moisture damage was found in the slab at an apartment adjoining wall.By reviewing literature written within the field of moisture problem, making hand calculations and modeling in the program Comsol Multiphysics, judgments are made to find explanations as to why the rise of moisture occurred in the building in Årby by.Generally, the following guidelines may be used to reduce the risk of moisture problems in slab-on-ground constructions:Drying of construction moisture before laying the floor material.Using draining layer beneath the slab, to prevent capillary suction.Using insulation under the slab, partly for comfort and to establish the temperature difference between the ground and the concrete slab.Avoid direct contact between the wood and concrete, due to degradation and fouling smells that normally occurs.If necessary, use additional vapor barrier.In addition to the above, there are various methods for moisture-proof and moisture-monitoring by design or by the method ByggaF suited for the entire construction process various events..

In Stockholm, Johanneshov the Slaughterhouse area (Slakthusområdet) can be found. A number of companies have gathered there providing the Stockholmers with meat products. This area has a great need for cooling to supply large cold storages. To facilitate this, a central cooling system has been built, supplying the area with effective and safe cooling.The aim of this master thesis study is to give hints to energy efficient and reliable changes that can be put in place at a low marginal cost depending on the future activities in the area. The suggested changes will be presented to the company Bravida (managing the system), which also desires a deeper understanding of the energy flows through the central cooling system.Firstly visiting the site with proper guidance, we have then tried to understand the function of the system including which machines and media that are used.

The purpose of this thesis is to collect knowledge of techniques and materials for planning roofgardens. Gardens built on top of buildings is not a new phenomenon, already in the beginning of the century architects were experimenting with roofgardens. During the Modern Era roofgardens appeared as a part of the design and worked well together with flat roofs and the ideas of light, air and greenery. Today the most common kind of roofgarden is on a ground-level joist that hides parking or other underground functions. The most important difference between planning a roofgarden and a garden on the ground is the limitation of the load of the roofgarden. Plants, paving-material and equipment must be chosen with this in mind. A light and thin layer of soil demands plants with small needs for water and nutrition.

When constructing a building, a number of aspects must be harmonized in order for it to fulfill requirements ? a building must fulfill requirements such a load-bearing, conservation of energy and a good indoor environment by means of, among other things, moisture proofing .Moisture problems in buildings can affect health negatively. As we are increasingly staying in indoors, demands on a good indoor environment are higher.This work starts with examining moisture problems in slab-on-ground solutions, and then links the various scenarios to moisture problems in a concrete slab of a real building. The building with moisture problems is located in Årby by in Borlänge and moisture damage was found in the slab at an apartment adjoining wall.By reviewing literature written within the field of moisture problem, making hand calculations and modeling in the program Comsol Multiphysics, judgments are made to find explanations as to why the rise of moisture occurred in the building in Årby by.Generally, the following guidelines may be used to reduce the risk of moisture problems in slab-on-ground constructions:Drying of construction moisture before laying the floor material.Using draining layer beneath the slab, to prevent capillary suction.Using insulation under the slab, partly for comfort and to establish the temperature difference between the ground and the concrete slab.Avoid direct contact between the wood and concrete, due to degradation and fouling smells that normally occurs.If necessary, use additional vapor barrier.In addition to the above, there are various methods for moisture-proof and moisture-monitoring by design or by the method ByggaF suited for the entire construction process various events..

The aim of this report was to investigate the economy of passive houses. The work was focused on economy in total and on the economy of different components such as windows, insulation, heat exchanger and the air tightness of the climate shell. No attention was paid on the comfort factor or to the impacts on the environment.Two houses, aspiring to be passive were chosen; A big one and a small one. Hence, comparisons considering the size of the building have been possible to do as well.The comparisons were made by calculating ?break even? between two concepts; passive and BBR- concept.

The purpose of the project has been to work out recommendations that reduce the energy-related costs and environmental impact of HPW Fresh & Dry Ltd., a fruit drying factory in Ghana. The factory produces electricity with diesel and biogas but also purchases electricity from the national electricity company. Heat for the drying process is produced from biogas, kerosene and solar panels. In the project the energy system was analyzed by measuring production and consumption of heat and electricity. The project results show that the factory can become self-sufficient on heat if the available energy is used more efficient. The production units for both electricity and heat have low efficiencies.

Passive houses are a relatively new concept in Sweden and by that it is meant a house without a traditional heating system. The most acknowledged passive house project is the terrace houses in Lindås, Gothenburg, which we have used as a reference. This project concerns a square apartment block. So far, no square apartment block has been built as a passive house in Sweden.The common opinion in the construction industry is that it is not economical to build extremely energy efficient houses. With Peab as commissioner our task was to investigate if that is true, if regarding the construction of a multi storey house as a passive houseMidroc, now owned by Peab, constructed in the block of Preussen in Jönköping during 2004-2005 four houses, with 132 apartments distributed on seven floors.

In recent years, moisture damages have been noticed in rendered, undrained stud walls. The design is built on the principle one-stage tightening which means that there is no air gap in the construction. The damages have occurred when water has permeated through the rendering in leaking connections and fittings for windows, doors, canopies, balconies, terraces and awnings. Behind the plaster carrier, which consists of either polystyrene or rigid mineral wool, plasterboard has often been used as a wind protection barrier. In many cases the wind protection barrier and the underlying wooden studs have been exposed to mould and in some cases even rot.