Within agriculture it is important to optimize the use of nitrogen, not only from an economic point of view but also to minimize damage to the environment. This can sometimes be difficult, especially within organic farming. Organic farmers are using increasing amounts of waste products from the food industry to cover their nitrogen needs. These different organic fertilizers release nitrogen at different rates and under specific soil conditions. Because of this, it would be beneficial to have a standardized method to measure the amount and rate of nitrogen mineralization from organic fertilizers. This project contributes to this knowledge by investigating whether relatively simple and repeatable laboratory methods can be used to estimate the nitrogen fertilizer value of organic fertilizers.

This work consists of two studies. One is based on an inquiery to nurseries with production of woody plants, and the other on visits to gardencenters, primarily in Skåne but also in Stockholm. Inquieries where sent to 87 nurseries, 48 of them replied. The purpous of the inquiery was to make a thorough investigation of the ligneous production at the Swedish nurseries, what is produced and in what quantities. Within the inquiery was also a thorough look at the fruit tree production. This to be able to conclude what cultivars that are produced and how large part of that production that is certified according to the Swedish Board of Agriculture (SJV).

In most countries, the dairy industry focuses on the volume of milk produced instead of its composition. This results in a high content of water and a lower proportion of fat and protein. A high proportion of water is not desirable when processing the milk into various dairy products like cheese, cream and milk powder. High water content also increases the costs for transport and storage, and also an unnecessary, albeit marginal, strains on the world?s water reservoir.

The report is about efficiency of a current production group where there is no clear production flow and there are some buffers between the operations. The efficiency is done with the help of a tool that is calledWork process of flow production which is used by Atlas Copco CTO. The most obviously results are that the lead time drops from 25 hours to 425 minutes and that the balancing loss decreases from 85 % to 8 %. The report focus on decreasing transports, decreasing buffers, more reliability in lead time and quality. And a more stimulating labour content for the workers is another result..

Today's society is facing major challenges. In order to reduce the climate impact fossil fuels should be replaced with fuels that do not contribute to the greenhouse effect. The growing population generates organic waste originating from industry and households so called organic fraction of municipal solid waste (OFMSW). Through anaerobic digestion, waste can be utilized to produce energy-rich methane gas. In this way, waste can be a resource instead of a burden on society.

At present, the Swedish pig industry is in transition. Prices have been low, but feed prices have increased. Therefore, many pig producers have stopped their production. Producers that lack an integrated production may contract piglet?s producers, or may use the mediation services that slaughterhouses provide.

If Sweden want to be able to compete internationally with its production capacity,it is important to work actively with production development and production ofresource-and time-efficient. This report is a bachelor thesis of 15 hp conducted atthe University of Halmstad. Using the principles of continuous improvement andLean Production, the author developed a concept for HAGS Aneby AB to changeto the customer order driven assembly of spring toys.First of all, the theories of Lean Production, logistics and ergonomics are used tobuild and present a theoretical framework for further examination. Then, toachieve the target, the current assembly process is analyzed to develop some firstconceptual ideas for improvement. In order to develop the best advice, theconcepts are evaluated against the company?s requirementsThe developed action plan gives recommendations on how the company shouldrestructure their assembly process and the organization of the related departmentin order to produce spring toys in a more time efficient and lean way.

Nowdays an efficient production is critical to achieve for companies competing on the market for steel cutting tools. One of such companies is Halmstad based Tooling Support Halmstad AB that manufactures threading-taps, threading-dies and parting off tools, towards a centralized warehouse in Schiedam, Holland. The large amount of different products, approximately 2500 is a big contributor to the problem along with a new order system that creates a demand of low setup times. Previously the company was forwarded orders through quarter based prognoses which enabled planning of the production over a longer time span. Currently the newer order system ZENIT is in use and the company thereby gets their orders weekly.

Automatic rumination measuring can be applied as a health indicator in dairy farming but is also highly desirable for research purposes. This study aimed to validate the technical functionality of the product RuminActTM, which employ acoustics to monitor rumination duration. The time budget of high yielding cows was studied and possible differences in rumination time between 13 rations were interpreted. Further the study examined what affects daily rumination and rumination efficiency. The validation was performed with direct observations that were compared to the automatically recorded rumination durations.

In order to investigate if the KRAV-regulations have any effects on the health and welfare of calves, KRAV-affiliated farms were compared to conventional farms with respect to calf management and outcome. The dairy calf has had a low economical impact during history. Even today the value of the calf is low and a lot of calves have a poor health status. The calf breeding is built on tradition and on the fact, that cheap antibiotics have made it possible to ignore, the recommendations about good hygiene in the calf?s environment.

In this thesis an energy analysis of ethanol production at the ethanol plant of Lantmännen Agroetanol in Norrköping has been performed. The ethanol plant has been studied in combination with Händelöverket, the combined heat and power plant which provides the ethanol process with steam. The purpose of this study was to determine the energy consumption for the whole production chain from grain to ethanol. The analysis has included the energy consumption for cultivation of grain, production of chemicals, the production chain for wood chips, the steam production and the ethanol plant. The grain and wood chips are both considered raw materials there for the energy content in these are not included as energy input in the system.

In this thesis an energy analysis of ethanol production at the ethanol plant of Lantmännen Agroetanol in Norrköping has been performed. The ethanol plant has been studied in combination with Händelöverket, the combined heat and power plant which provides the ethanol process with steam. The purpose of this study was to determine the energy consumption for the whole production chain from grain to ethanol. The analysis has included the energy consumption for cultivation of grain, production of chemicals, the production chain for wood chips, the steam production and the ethanol plant. The grain and wood chips are both considered raw materials there for the energy content in these are not included as energy input in the system.

In connection with Henriksdals wastewater treatment plant (WWTP) a smaller plant is situated called Sjöstadsverket where new methods for wastewater treatment are tested and evaluated in different process lines. On one of the lines experiments with enhanced biological phosphorous removal (EBPR), have been carried out to evaluate if it is a good alternative to traditional chemical phosphorus removal. This thesis evaluates the results from the experiments conducted during fall 2005.The incoming water from Hammarby Sjöstad consists of only household wastewater, which gives a wastewater with high concentrations of nutrients and organic carbon. This is partly positive, because one of the limiting factors for effective biological phosphorus removal is the lack of easily biodegradable organic carbon. The high concentrations of ammonium and phosphorus demand a high reduction to achieve the requirements of outgoing concentration.To optimize the process experiments with different recirculations and different aeration techniques have been made.

Lean Production har sedan länge enbart varit förknippad med tillverkningsindustrin och främst Toyota genom Toyota Production System(TPS). På senare år har Lean Production i allt högre grad introducerats och integrerats i tjänsteföretag under beteckningen Lean Service. Bankbranschen är en bransch där aktörer globalt anammat de bakomliggande filosofierna av Lean Production och Lean Service. I det här arbetet har en undersökning gjorts kring huruvida Lean Production existerar inom svenska banker och om så är fallet hur filosofierna inom Lean Production präglar bankerna. De tre bankerna som valts för undersökningen är de svenska storbanker Nordea, SEB och Handelsbanken.

One of the most distinguishing features of contemporary globalisation is production fragmentation, a splitting up of the manufacturing of a good into several different stages. Production fragmentation creates new opportunities through vertical specialization; a country incapable of mastering the entire production process may specialize in the manufacturing of one separate part. The aim of this thesis is to examine to what extent international integration affects a country?s ability to engage in vertical specialization in an industry characterized by production fragmentation. The analysis focuses on the european integration process over the last decade, where countries in eastern Europe with relatively low labour costs have been integrated with more capital abundant western economies.