Nanotechnology, one of the most interesting sciences today will no doubt have an enourmous impact on tomorrow's society and industry. One of the most interesting nanomaterial that has been discovered is the semiconductor quantum dot (QD). This material shows interesting novel properties such as a size-dependent band gap, which is an effect caused by the quantum confinement effect in all three dimensions. Due to this phenomenon the absorption spectrum can be tuned to the desired value by adjusting the size of the QD.This thesis aims to investigate how the solvent ratio of H2O/Ethanol affects the optical and structural properties of copper sulfide QDs manufactured in a chemical synthesis way using modern microwave heating. The process of manufacturing QDs using chemical synthesis often involve a capping-agent to prevent the QDs from agglomerate into bigger structures.

The company LightLift Esystems AB manufactures patented motorized lift systems for the illumination of halls with high ceilings. The company wants a new design for singular heavy lights in order to be more competitive.This project consists of the development of the new design under the requirements and specifications imposed by the company. The new design must support lights up to 300kg and keep the overall dimensions as low as possible without modifying the driving unit.This document contains all the designing steps followed to reach the final solution as well as the material selection, manufacturing process and assembly of all the parts that form it.The solution obtained shows to be very competitive with other alternative products, since this new design triples their maximum load capacity while the dimensions are very similar.In this context, the optical appearance was also very important to the company and so it was another main objective of this project. From an aesthetical point of view, the final solution proves to be very compact and versatile since it can either be hidden behind a false ceiling or covered by a plastic case that gives the design a very nice look.Finally, the solution achieved fulfils all the requirements and specification previously imposed. It is reliable, compact, cheap to manufacture, easy to assembly and it has a good optical appearance. .

Until the beginning of the 1900:th century the paper making process was handicraft. The paper machines that have been developed since then are as impressing in size as fascinating when it comes to the technique. The process has always been improved to give a better paper for lower costs, with as short manufacture time as possible. Stratified forming has been a reality since 1830. From the beginning it was applied to board and paperboard.

Mitt arbete handlar om mötet mellan rysk konstruktivism och science fiction. Detta har jag gestaltat i ett textilt rum inspirerad av science fictionkarraktären Doktorn ur Doctor Who. Doktorn är en utomjording av en långt mer utvecklad art och från en mer avancerad civilisation än människorna, som reser i tid och rum i sitt tids-och rymdskepp TARDIS. Jag har designat ett rum som är min textila tolkning av TARDIS innersta. Arbetet kretsar kring tankar om gestaltning av en flerdimensionalitet som bara kan anas, inte ses eller förstås.

The problem of separating a non-rectangular foreground image from a background image is a classical problem in image processing and analysis, known as matting or keying. A common example is a film frame where an actor is extracted from the background to later be placed on a different background. Compositing of these objects against a new background is one of the most common operations in the creation of visual effects. When the original background is of non-constant color the matting becomes an under determined problem, for which a unique solution cannot be found. This thesis describes a framework for computing mattes from images with backgrounds of non-constant color, using Bayesian statistics.

Introduktion: Dental erosion definieras som förlust av tandens hårdvävnad genom en kemisk process som inte involverar bakterier. Dagens förändrade livsstil och kosthållning medför att våra tänder oftare utsätts för kemisk påverkan som kan leda till erosion. Det är flera faktorer som samverkar och dental erosion har en multifaktoriell etiologi.Syfte: Syftet är att beskriva olika registreringsmetoder för dental erosion.Frågeställningar: Vilka metoder kan användas för registrering av initial erosion? Vilka metoder kan användas för registrering av avancerad erosionsskada? Vilka metoder är kliniskt beprövade på patient?Metod: LitteraturstudieResultat: Ett flertal registreringsmetoder fanns beskrivna i litteraturen, merparten var inte applicerbara kliniskt. Registeringsmetoderna som framgick i den beskrivande litteraturstudien var: 3D scanning microscope (IFM), Atomic absorption spectroscopy (AAS), Digital photography (DP), Focus-variation 3D microscopy (FVM), Longitudinal microradiography (LMR), Non-contact confocal laser scanning microscopy (CLSM), Optical assessment, Optical profilometry (OP), Quantitative light-induced fluorescence (QLF), Scanning electron microscopy (SEM), Stylus profilometry (SP), Ultrasound, White light interferometry (WLI) och X-ray diffraction (XRD).Konklusion: Vid registrering av initial erosion krävs analys av tandytans mineralinnehåll samt optiska analyser med hjälp av instrument.

Platelet aggregation is a major and common problem in blood samples from cats. This greatly affects the accuracy of counting of the platelets. Because of the difficulties in counting feline platelets, results for patients and reliable reference values for cat platelets are currently so inaccurate as to be almost useless in diagnosis of thrombocytopenia. In this study we used an effective method to prevent platelet aggregation. Blood was collected in CTAD test tubes and prostaglandin E1 was added to the blood sample.

The thesis mission is to investigate whether the swiveling laser that Vectura (former Vägverket Konsult) has in use to measure the road areas and straddle measuring can be used to detect differences in the reflective road markings function. This is to increase use of the swiveling laser and get rid of the manual measurements performed today.Currently, the measurement of road markings reflective function is performed with both mobile and handheld measuring instruments. The purpose of this thesis is to develop better methods for determination of road markings? reflective function, in order to facilitate the description and suggestions for improvements of the maintenance of road markings reflective function.The questions that the thesis has been to start with are:Can the swiveling laser detect differences in longitudinal and transverse road markings reflective function?The accuracy of measurement has been sweeping the laser over the reference instrument (LTL-2000)Is it necessary with a conversion factor for swiveling laser data against the reference instrument data?To answer the question 2 and 3, there has been a field work in Värnamo where a road stretch with longitudinal road markings and zebra crossing (transverse road markings) has been investigated with a swiveling laser and LTL-2000.The formulas and calculations contained in the thesis are drawn from scientific reports that are produced by VTI in Linköping. The same formula that was used to calculate the optical measurement data was also used for the swiveling laser data.

The purpose of this master thesis has been to find different solutions to the design of a headlamp with a cluster of three or possibly four high power LEDs (Light Emitting Diodes). During the work, two different problems have been considered; how to design a lens in order to shape the light beam in a desirable way, and how to design a cooling system which will lower the temperature of the LEDs as efficiently as possible, still taking into account the geometry set by the optical solution as well as other given geometries. The results presented in this thesis are partly the outcome of a literature study, but derive mainly from a number of tests and measurements made on two test rigs and one concept prototype..

Denna rapport handlar om optisk koherenstomografi, Optical Coherence Tomography (OCT), en relativt ny teknik som blivit allt mer attraktiv på sjukhusens ögonkliniker. En OCT-apparat används bland annat för diagnosticering av ögonsjukdomar lokaliserade i gula fläcken och runt optiska disken. I maj 2007 köpte Ögonkliniken på Blekingesjukhuset in en 3D OCT-1000 av märket Topcon. Hos denna OCT-apparat finns en mätfunktion, Caliper, som mäter näthinnetjocklek. Studien i denna rapport syftade till att ta reda på vad Caliper mäter, hur den mäter och om den går att lita på.

Denna rapport handlar om optisk koherenstomografi, Optical Coherence Tomography (OCT), en relativt ny teknik som blivit allt mer attraktiv på sjukhusens ögonkliniker. En OCT-apparat används bland annat för diagnosticering av ögonsjukdomar lokaliserade i gula fläcken och runt optiska disken. I maj 2007 köpte Ögonkliniken på Blekingesjukhuset in en 3D OCT-1000 av märket Topcon. Hos denna OCT-apparat finns en mätfunktion, Caliper, som mäter näthinnetjocklek. Studien i denna rapport syftade till att ta reda på vad Caliper mäter, hur den mäter och om den går att lita på. En OCT-undersökning utfördes på tio testpersoner.

The Blötberget deposit is situated in the north-western part of Bergslagen. The mineralization is an apatite-iron oxide ore of Kiruna type. In Bergslagen the apatite-iron oxide ores occur along a zone from Grängesberg through Blötberget to Idkerberget in the northeast and they represent the largest and the most important iron oxide deposit in Sweden, south of Norrbotten.Different REE hosting phosphate phases has been studied by optical microscopy and analyzed by EDS attached to an electron microscope.The key minerals other than iron oxides are apatite, monazite and xenotime. The relative concentration of the REE-bearing phases differs from the other apatite-iron oxide mineralizations in the area, for example Grängesberg, by a higher concentration of xenotime and lower contents of allanite..

This Bachelor of Science thesis was carried out at Metso Panelboard AB, located in Sundsvall, Sweden. The work lasted for 10 weeks and began at the end of February 2007. Metso Panelboard is one of the leading suppliers of complete lines, single machines, engineering knowledge and after-market services to the fibreboard industries. The task involved building a 3D-model of a dryer cyclone in the CAD-program Pro/ENGINEER. A dryer cyclone is the part where the tree fibres are dried in the process of manufacturing fibreboards. Currently, it takes about two weeks to draw a dryer cyclone. By creating a 3D-model of it, which should have the functionality to be generated to different sizes, the goal is to decrease the drawing time to about 20 hours and to increase the quality of the work. This report includes the fundamental theories behind the manufacturing of fibreboards with focus on the dryer cyclone.

Background: Low back pain (LBP) is a common disorder in the western world. A majority of those afflicted by a first acute episode is at high risk of developing sub-acute or persistent symptoms. Persistent LBP can be caused by pathological changes in the discs and disturbed neuromuscular activation, which can cause hypotrophy of the extensors strong type-2 muscle fibres. Deadlift (DL) is an exercise that may correct all these pathological transformations. Aim: To investigate the effect of DL-training on patients with persistent LBP.

Outside of many Swedish households today, you will find a typical green wastecontainer. This container has not changed since its introduction, despitecomplaints about foul-smelling and its impractical system. Even if the system usedtoday, still is the most optimal choice, there is a lot of newly developedalternatives out there.Its purpose is to get a broader perspective on how a waste management systemcan be developed into a working, land efficiently and aesthetically pleasing systemof humans and the environment in a small residential area.The authors treat the residential area of Jära, Ekhagen, in Jönköping, which ismanaged by JM AB as a problem area in regards to waste management.The issues raised by the authors are the different waste management systems usedin the corresponding areas of the world, how to apply technical andenvironmental as well as the waste management facilities from financial aspects.In the process, the methods used were literature reviews, case studies and aninterview. The case study was done through a modeling of waste managementsystems in the area Jära and an interview was conducted with the company Envacworking with vacuum systems. Studies have been made by different systems n theareas around the world.The results show that using directives and guidance will reduce the environmentalimpact done without replacing the traditional system.