Single vehicle accidents are one of the most common types of accidents that occur on the Swedish road network. Depending on the design of the road, the presence of a crash barrier and embankment on the roadside, the outcome of a roadside collision can lead to serious injuries and even deaths.The aim of this project is to investigate the possibility of improving road safety by designing the optimal roadside area based on the results of a life cycle cost analysis (LCC).The questions that have been answered during the duration of this project are:1) Describe the current technical solutions for roadside area design and the various barrier types used in Sweden.2) Complete an existing mathematical model that has been developed by Hawzheen Karim, for calculating life-cycle costs for various roadside areas.3) Calculate and compare the life cycle costs for the side area with a barrier and without a barrier.By performing an analysis of the documentation on the current guidelines and rules for shaping the roadside, was it possible to describe the current technical solutions for the formation the roadside as well as the current roadside barriers in use today. A mathematical model for calculating the life cycle costs of different barrier types had already been developed by Hawzheen Karim. This model was supplemented so that it could calculate life-cycle costs of the roadside region with and without a barrier. After the model was completed, an analysis was performed to obtain life-cycle costs of a roadside with and without a barrier.The result showed that there is a clear relationship between the slope inclination, fill height, and the rate at which the costs rise.

This report describes the master thesis project ?Weight Optimization of a Composite Chassis for a Multimodal Lightweight Vehicle? which is a part of the Master program in Naval Architecture and a part of a research project at the Centre for Naval Architecture, KTH. Demands on smart and energy efficient transport solutions are continuously increasing. In the Stockholm region the citizens are expected to increase with 25% and the road vehicles with 80% until 2030, putting high demands on the traffic system. Using a small multimodal vehicle deals with this problem and uses both the land and waterways for transportation.

The basis of road investments is to minimize the transportation cost. The forest industry wants roundwood to be available during the whole year. One way of determine which road to invest in is to do a cost/benefit calculation. SCA Forest lacks a uniform approach to determine the utility of a road investment. The goal of this report is to describe how the organization works today and find areas of improvement. The data collection was done through interviews.

Saab Aerosystems has a long tradition and a lot of competence in the field of flight simulation. Their ambition to broaden the market horizon has led to a discussion about also selling vehicle simulation solutions, both for military and civilian use.The aim of this thesis is to investigate the driver?s experiences of the accelerations he or she is exposed to whilst driving in rough terrain. The results may be used as a basis for future decisions and can act as a platform for the construction of an effective simulation model.To investigate the driver?s exposure of acceleration, some kind of dynamic simulation is needed.

Abstract Road cycling is well established and has always been described as a highly endurance sport. To be able to compete in such a demanding sport the physiology of the athletes needs to be greatly developed. This review will focus on high intensity interval training and its impact on the physiological characteristics of competitive road cyclists. The main difference between different levels of competitive road cyclists seems to be the capacity to maintain a high sub maximal power output over a long period of time in order to succeed. High intensity interval training, from 30 seconds to 5 minutes, leads to improved VO2peak, aerobic peak power and time trial performance.

The study was conducted with an landscape approach with an subject related approach in the field of environmental psychology to investigate how road design affects drivers' choice of speed. The purpose was to portray road environments on thoroughfares in urban areas to motivate motorists to keep the speed limit and thus increase road safety for vulnerable road users. The task question was formulated, how can thoroughfares in suburban settings be portrayed to motivate motorists to reduce speed? The study was conducted throughout a literature review of motivational speed measures along with interviews with road design experts at the Swedish Transport Administration. Case studies were conducted on three thoroughfares in the Stockholm suburbs Vallentuna, Upplands Väsby and Danderyd.

The thesis mission is to investigate whether the swiveling laser that Vectura (former Vägverket Konsult) has in use to measure the road areas and straddle measuring can be used to detect differences in the reflective road markings function. This is to increase use of the swiveling laser and get rid of the manual measurements performed today.Currently, the measurement of road markings reflective function is performed with both mobile and handheld measuring instruments. The purpose of this thesis is to develop better methods for determination of road markings? reflective function, in order to facilitate the description and suggestions for improvements of the maintenance of road markings reflective function.The questions that the thesis has been to start with are:Can the swiveling laser detect differences in longitudinal and transverse road markings reflective function?The accuracy of measurement has been sweeping the laser over the reference instrument (LTL-2000)Is it necessary with a conversion factor for swiveling laser data against the reference instrument data?To answer the question 2 and 3, there has been a field work in Värnamo where a road stretch with longitudinal road markings and zebra crossing (transverse road markings) has been investigated with a swiveling laser and LTL-2000.The formulas and calculations contained in the thesis are drawn from scientific reports that are produced by VTI in Linköping. The same formula that was used to calculate the optical measurement data was also used for the swiveling laser data.

A vehicle that carries a person sitting in a wheelchair has been rebuilt. The original vehicle was provided with a petrol engine, hydrostatic drive and a mechanical steering rod, making it noisy and hard to maneuver. The purpose with this project was to convert the vehicle to make it more environmental and easier to drive.A new design has been proposed where an electrical drive has replaced the noisy combustion engine and an electrical motor with joystick control has replaced the manual steering.The project was divided into two parts. One mechanical part where the construction of the drive and steering were to be decided. The other part involved programming the microprocessor and implementation of all the necessary electrical for the control system of the vehicle.

AbstractThe dependency of fossil fuels in the transport sector causes large emissions of carbondioxide. This problem can we reduce by using vehicle gas from digested solid manure and leftover of pasture. I have studied the potential for this in the county of Västernorrland. Thepurpose is to investigate how much vehicle gas that can be extracted.One central, large scale digestion and upgrade plant should be placed in Härnösand. Theamount of pasture and manure that is economical and practical available is enough to produce2,7-3,5 millions Nm3 vehicle gas.

Road design with focus to safety has been extensively developed in last decades in Nordic and some other EU countries with the main aim to achieve a decrease in a number of accidents and fatalities on the roads. These countries gained many valuable experiences, but they had to sacrifice great effort, expenses, and time to reach the present art-of-state. The purpose of the Master?s Thesis is to review some design approaches with focus to safety and discuss the general way that they may be applied. The Master?s Thesis studies safety in three levels: (i) general - design standards, national safety policies and road hierarchy; (ii) local authority and road administrator; and (iii) three specific safety countermeasures - junctions, pedestrian crossings and traffic calming.

This report covers the conceptual design of a new one person hybrid vehicle that is to be fast and convenient to drive on the roads. The vehicle is most of all supposed to be used as a commute vehicle but can also be used at other occasions as well.During the work with this project the group has focused on three larger areas, the outer design (body), wheel chassis and an ergonomically designed interior. The group was not able to just create these parts in 3D to get a trustworthy vehicle, hence number of other components and details were also created to get a better entirety.The outer design starts with idea generation and sketches and ends with a 3D model which is rendered to show how the final product is going to look. The design of the body has been going on during the entire work process due to new ideas and improvements that seemed interesting and had to be changed.The wheel chassis also started with idea generation, research and sketches. It ended up with a simulated 3D model which later on was mounted on the vehicle body to show how the vehicle is going to perform during usage.

When constructing a road the risk of emission of substances from the used materials to the surrounding environment has to be evaluated. The aim of this study is to present a proposal for how to evaluate the risk of contamination as a result of emission from the materials in a road construction. The study is based on literature studies, an inventory and a questionnaire that examines how experts in governmental agencies, industries and universities evaluate the risk of contamination. The inventory indicates that guidelines for evaluating the risk of emission from secondary materials in a road construction do not exist. The conclusions from the questionnaire are: that there is no common way to evaluate the risk of contamination as a result of emission from materials in the road construction, there is no uniform interpretation of the terms "minor" and "significant" risk of contamination and that the evaluation is subjective.

This thesis is an evaluation of the new traffic solution at ?Skvallertorget?. The innovative theory behind it is to increase traffic-safety by introducing insecurity feelings for road-users. The conclusion of the evaluation is that the newtraffic solution is well adjusted according to guidelines for municipal traffic planning. The evaluation also illustrates the conflict between traffic planners deliberate attempt to avoid clear information and the road users wish to get it.

Through previous studies during my education, I have experienced that chemical deicing road salt is a known problem, mainly in southern Sweden. Road salt causes damage to the environment and also damage to vehicles and structures such as bridges, etc. Road salt causes vehicles and steel constructions to rust, leading to increased costs for repairs of damage to structures. Road salt also causes damage to the plants and the economy to suffer, when plant material and soil needs to be replaced. In order to get closer to a solution, I put up three questions.

  Befintliga studier har påvisat att genetiska algoritmer presterar bättre om de ges en bra startpopulation. I denna rapport presenteras en lokal sökalgoritm för att skapa en population med fokus på ?vehicle routing?-problem. Algoritmen använder sig av heuristik i en blandning av simulated annealing och tabu search för att skapa individerna till populationen. Utvärderingar av algoritmen på ett praktiskt problem visar att den ger en bra start jämfört med en slumpmässig startpopulation, vilket är vanligt att använda.