An energy study has been performed on two blocks in an area called Gävle Strand. The buildings are owned by a tenant-owner?s association called brf Carolina and were built by the company Skanska 2008. The builder as well as brf Carolina are pussled by the fact that electricity use is higher than expected while heating is less. Skanska is also very interested in finding out how much heat recovery from stale exhaust air through a geo-thermal heat pump is contributing to the general heating requirement and energy balance in four out of the ten buildings located on the properties.To find possible answers to the higher electricity use a literature survey on user behaviour was conducted.

The purpose of the thesis was to map the hydraulic load on the Knivsta river from stormwater runoff, and build a platform for further studies of pollution loads on the rivers ecosystems. New residential areas are planned to be built in Knivsta municipality and it will have an impact on stormwater flows to Knivsta river. To examine the impact this will have, simulations were made in the area as it stands today and after expansion work. The work includes calculation of flows from the populated areas but also from the catchment area around it consisting of woodlands and fields. Because of expected climatic changes which may affect rainfall, the simulations have been performed with different return periods for rainfall data.

WSP building physics in Stockholm has certified the preschool Temmelburken in Bromma with the system of certification Miljöbyggnad. The rating of the building became BRONZE. In this thesis the preschool has been investigated with respect to the three areas: thermal climate, use of energy and improving of the level of certification. The thermal climate at the preschool has been investigated by a questionnaire survey and by measurements in order to do comparisons between the results from the two investigations as well as with the results of the simulations that WSP has done at the certification of the preschool. The differences between the results from the simulations and the questionnaire survey for winter as well as from the measurement performed with a comfort meter the 19th of March are concidered to be reasonably small since they give rise to the same rating according to Miljöbyggnad.   Operational data for the use of energy for the preschool have been obtained in order to do comparisons with simulations performed by WSP and Svenska Besiktningar AB. The comparison shows that the simulated values for the specific use of energy are lower than what the real specific use of energy would be for the preschool, since just the operational data for the heat energy is higher than the simulated values. At the investigation of the possibility of improving the level of certification it was found that the rating of the preschool can be raised from BRONZE to SILVER by improving the ratings of the ?thermal climate summer? and the ?daylight?.

This study examines the background and nature of the credit default index swaption (CDIS) and presentsrelevant methods for modelling credit risk. A CDIS is a credit derivative contract that gives the buyerright to enter into a credit default index swap (CDS index) contract at a given point in time. ACDS index, in turn, is a multi-name credit default swap (CDS). Within the eld of research, thisthesis identi es the CDIS pricing models presented by Jackson (2005), Rutkowski & Armstrong (2009)and Morini & Brigo (2011) as the most recognized and developed. These models are evaluated byreconstruction in a numerical software environment.

An energy study has been performed on two blocks in an area called Gävle Strand. The buildings are owned by a tenant-owner?s association called brf Carolina and were built by the company Skanska 2008. The builder as well as brf Carolina are pussled by the fact that electricity use is higher than expected while heating is less. Skanska is also very interested in finding out how much heat recovery from stale exhaust air through a geo-thermal heat pump is contributing to the general heating requirement and energy balance in four out of the ten buildings located on the properties.To find possible answers to the higher electricity use a literature survey on user behaviour was conducted.

The supply of uninterruptible power can be applied to many areas wherecontinuous operation is highly prioritized.The application of uninterruptible power for motor operation is facilitatedusing a frequency converter. Direct current operated frequency converters canbe applied directly to the power reserve which removes the need for additionalpower-converting.Batteries have long constituted the power reserve but advancements inthe development of ultracapacitors have created a viable substitution. Ultra-capacitors have high energy storing capabilities and can be applied to highpower applications.Maxwell is a leading manufacturing company of ultracapacitors and pro-vide different modules with built-in solutions for voltage balancing. Unevenvoltages between series-connected capacitors is a phenomenon caused by vary-ing capacitance. A configuration containing Maxwell?s 56V module is createdand constitutes the power reserve in the simulations.The discharge simulation shows a significant current that could damagethe system.

The aim of this thesis was to investigate if the robotized welding method FSW (Friction Stir Welding) could be applied for joining a rotating structure in an aero engine at Volvo Aero Corporation. FSW is expected to introduce less defects than today?s welding methods and could therefore be suitable for critical aero components. The material is the nickel based alloy Inconel 718, however a material experimentation is outside the scope of this report.The main goal of this study is to verify if the ESAB ROSIO robot based FSW-system has a suitable work space to be able to weld the rotating structure, and if the welding tool has accessibility to the joints. The FSW-process needs a rigid fixture, and a number of fix-ture concepts are presented based on a proposed weld sequence.

Simulations of simulink models using Kalman filters are often very time-consuming. This problem depends mainly on the fact that the Kalman correction has to be performed at each sample instance through the whole simulation. The goal for this thesis work is to reduce that time-consumption for the filtering part (the integration partis treated in a complementary report) of a simulation. Furthermore a Matlab routine to perform parameter tuning and finally a graphical user interface is developed.The filtering part of the simulation in this thesis is based on an Extended Kalman Filter (EKF). The time optimization of this filter considers searching for the possibility to replace the today?s existing Matlab functions that is used to perform the filtering calculations.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

This thesis is made on behalf of SCA's Forestry Division and is a comparison of two bucking simulation tools: Aptan (manufactured by Skogforsk) and Best/upr (from Berget Systemdesign). The data is based on 32 stands from SCA's forests in Norrbotten and Västerbotten. The objective is to compare the simulations created by the tools with the harvested volumes from those stands. Three variables are needed for the bucking simulation; these are the diameter distribution (at breast height), the relationship function between diameter and height, and the taper coefficients. The volumes of five different assortments from the stands are compared.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

This master thesis has been performed at Solvina in Gothenburg for Skellefteå Kraftand Vattenfall Eldistribution. The aim of it is to investigate the consequences of theinstallation of a wind power plant on the mountain Uljabuouda in the vicinity ofArjeplog. Especially the impacts on voltage and transient stability are examined.Furthermore, the amount of extra strain on the voltage regulation equipment and theneeds for increased regulation capabilities are looked into.The wind power plant is planned to be built by Skellefteå Kraft and connected to a130 kV grid owned by Vattenfall Eldistribution. The work comprehends the followingmain parts:- Theoretical studies aimed at wind turbines and power system stability issues.- Modelling of the type of wind turbines assumed to be built on Uljabuouda.- Simulations of different operation cases and analysis of the simulation results.The results from the simulations show that, as far as voltage stability and extraworkload on tap-changers are concerned, the wind power plant does not, in anysignificant manner, worsen the present conditions. The problem of overloading theline between Arvidsjaur and Vargfors is also minor.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.

The purpose of this thesis has been to develop a tool for modelling and simulating the nuclear plant Ringhals 3. The model should be used to improve the knowledge on the dynamics of the plant. Ringhals 3 is being upgraded to produce more power and a tool for analyzing the new operating conditions is needed.The work in this thesis has consisted of improving and developing an existing model of Ringhals 3 made with the modelling tool Dymola. The model has been validated by comparing the results of a simulated house load transient with data from the actual plant. Validation shows good agreement with data from the real plant.