This master thesis encompasses an inventory of the older industrial community of Gimo. Investigations of the contamination situation for each industrial area were done. A risk classification according to the Swedish Environmental Protection Agency?s ?Method of Surveying Contaminated Sites?, phase one, followed. The risk classification was done on areas of Iron Work, a rockwool industry and a landfill. Gimo have had iron manufacturing from 1615 until 1945. Gimo have had two blast-furnaces and two smithies periodically.

ABB Capacitors Ludvika started their LEAN-project in november 2010, but still has not the whole factory been introduced to the LEAN-tool called 5S. 5S is only implemented on the ?easiest? work-areas.By implementing 5S, at the workingstation called inburkningen, would make the workstation and the area around it much more structured, clean and systematized. The operators are a little bit skeptical to the work that includes continuous improvement today, because they can not see any progresses. If 5S were implememted the operators would be able to avoid searching for tools because with 5S, each tool will have a specified place at the workstation.5S would simplify the cooperation between the shifts, because 5S includes clear instructions for how the workstations will be cleaned after each shift.This report will include my recommendations, thoughts and opinions regarding however ABB Capacitors Ludvika should implement or not implement the LEAN-tool 5S.

LEXION is the name of the largest series of combines made by the CLAAS factory in Germany. LEXION was introduced on the Swedish market 1996 and was for sale in Sweden from 1997. LMB have sold over 400 LEXION-combines in Sweden. In cooperation with the Swedish general agency we decided to make a market research on the Swedish LEXION-market. The questionnaire was supposed to give answers about capacity and technical equipment. Before I made the questionnaire I studied manuals and combines. I got 81 answers of about 325 questionnaires. That makes 25 % reply frequency.

This report is a bachelor thesis work in the field of product development and design. The assignment has been to develop a solution for roof racks, normally used for cars, to fit on the open trailer models FS1425 and Alugance. The project was implemented by Johan Andersson and Victor Karlsson, students at the Mechanical Engineering program with a focus on product development and design at Jo?nko?ping?s school of Engineering, in spring 2012.The client wants to use transport solutions in the same way as roof racks on cars. The user of such a product is assumed to desire simplicity, safety and an attractive design with an appealing price, which has been a challenge during the thesis work.Pre-studies have been conducted to examine the potential competitors and gain knowledge in the research area.

The thesis that follows is performed in collaboration with Nitator in Oskarström.The factory in Oskarström focuses on laser cutting, robotic welding and surfacetreatment of steel for the automotive industry.The project aims to streamline the flow of materials in production by automatingthe movements of the forklifts, running to and from the interlayer, and betweenworkstations.The project started with a systematic literature search. The literature searchshowed the research position around the AGV-system. Also a review of studentliterature was made, so that a suitable method for practical implementation couldbe developed and applied. Selected method uses both quantitative and qualitativeapproaches, which is analyzed by using triangulation.The work has resulted in a modified layout of the current facility in Oskarströmthat can be used for the implementation of the AGV-system. It has also resulted inthe tender documents and profitability calculation from several of AGV-suppliers..

The construction industry is currently receiving much criticism for inefficiency and slow development while demands for reduced built in moisture and efficiency increases. This report examines whether the use of field factories can meet these requirements and what factors that will be critical for future use of field factories. Industrialized construction with field factory is compared with traditional loose timber construction and industrial construction in the fields of execution, logistics and working environment. The aim of this report is to provide a basis for field factories current and future use and development. To achieve the aim of the report, people with experience in the use of the various methods was interviewed and literature studies in the various fields done.

AbstractDegree thesis Solid content in Lime Mud By Andre Flodin Process operator program ? Umeå University 17/6 ? 2014 Pages: 21A thesis was made on Billerudkorsnäs production unit in Karlsborg where lime kiln in the causticising department of chemical recovery plant does not meet the required production. Causticising department is the final step in the chemical recycling unit. There, the filtered green liquor is mixed with lime to recover the cooking chemicals used in the pulp factory. The cooking liquid is called white liquor.

Examensarbetet har utfo?rts av Ida Montan, maskiningenjo?rsprogrammet pa? Karlstad Universitet. Arbetet har skett i samarbete med Swenox AB. Ett fo?retag vars produktion a?r bela?gen i Nyko?ping.

Examensarbetet har utfo?rts av Ida Montan, maskiningenjo?rsprogrammet pa? Karlstad Universitet. Arbetet har skett i samarbete med Swenox AB. Ett fo?retag vars produktion a?r bela?gen i Nyko?ping.

Sewer trenches usually contain material with a higher hydraulic conductivity then the adjacent soil. Thus they can serve as paths of preferential flow in a polluted area. Wastewater from factories can also leak from wastewater pipes and pollute the soil in the sewer trenches.The purpose of this project was to investigate pollutions in sewer trenches and in sewer pipes in the industrial area of Köpmanholmen, 20 km south of Örnsköldsvik in the north of Sweden. To make an estimation concerning the potential of transport of pollutions in sewer trenches, hydrological calculations were performed.Leakage to any greater extent did not seem to be a problem in the area. This is the case both for the concrete and the wooden pipes that have served as factory wastewater pipes.

This paper argues that the food industry in general and the one taking place in Scania in particular, are disregarded in the official management of industrial preservation carried out in Sweden today. Despite the articulated ambition of a cultural heritage that as many as possible could identify with, the practice tend to create an industrial heritage based on stereotype ideas about the landscape in Sweden and the characteristics of industry. The way the open land of Scania differs from the traditional image of the appearance of Sweden, is used as one possible way to explain why the food industries of Scania are overseen in the management of industrial heritage. It is also argued that the high number of female employees might bee a reason why the food industries in general are given low priority in the practice of cultural heritage. By putting the Findus pea industry and the cultivated landscape that provides the factory with primary products against the official criteria for industrial memories, it is examined what values for preservation the food industry contain..

Volvo Penta has been producing boat engines since 1907 and are world leading in this seg­ment. They have today an extended range and also sell industrial power stations. Quality, safe­ty and environmental care are three core values for Volvo and together they strive to give their customers the right product with the right quality.Volvo has developed a production system named Volvo Production System, VPS, and one of the pillars is continuous improvements. Within this pillar you can find value stream map­ping, which is used to analyze the value stream through the process. This tool gives a wide perspective and helps to keep focus on the entire process instead of just parts of it.Volvo Penta in Vara has earlier done value stream mapping but without good results since they didn?t take set-up times and imbalances in account.

Industrilandskapet is an area in central Norrköping who has undergone major changes during the 1900s. The area has in recent decades gone from being an important industrial area into a place that today is focused on knowledge production and visit activities. This study focuses on how four selected businesses in Norrköping look at the change that Industrilandskapet has undergone. The four businesses all have in common that they use and care of Industrilandskapet in both marketing and as a working place. The businesses are in this study represented by four informants who were interviewed with semi-structured interviews.The results from the informants are analyzed by support of theoretical points.

Volvo Hauler & Loader Division in Arvika produces wheel loaders which they deliverthroughout the world. The factory which is situated in Arvika is the largest wheel loader plant in the whole world, with its 1 100 employees. The different models stretch from L60E all theway up to the brand new L350F, with a loader capacity from six tons up to a staggering 35.The assembly of the different models are divided into three different assembly lines, Small(L60-L90), Medium (L110-L120) and Large (L150-L220). The assembly of Heavy (L350)has just been started with an upcoming pre series.This examination paper gives recommendations of improvements and necessary modifications to rationalize the pre-assembly of boom units. Three different scenarios are presented in the paper.

Construction companies are frequently criticized for high prices and long construction time. At the same time, statistics shows that construction workers are on the sick-list for occupational injuries or casualties more than other groups at the labour market.Skanska built a block of flats with tenant-ownerships in Gävle. The construction consists of concrete walls with in-fill walls in the front. The purpose with this degree project is to perform a risk analysis in work environment with focus on repetitive strain injuries and control the time report for in-fill walls manufactured in a field factory. The result of this project will help to make more realistic cost predictions in the future.This degree project has been performed in cooperation with the construction company Skanska.