This thesis is the result of the investigation and solution of a mechanicalproblem regarding flywheel malfunctions. A flywheel is, in short, a devicethat relies on a rotating object?s moment of inertia to store energy overshort time spans. This project is part of the development of a fourthflywheel prototype at the division for electricity at Uppsala university,which uses magnetic levitation to keep a hollow cylinder rotating at veryhigh speeds inside a vacuum chamber. Should the magnets fail however, orsome other error occur that leads to an uncontrolled state of rotation, thecylinder needs to be stabilized mechanically by a device usually referredto as ?back-up bearing?.

Good comfort for the driver of a construction machine is crucial. Gearshift comfort is an important part of the total comfort. Volvo Construction Equipment Components has a simulation environment of the powertrain, SimPow, which is implemented in Matlab/Simulink. SimPow is mostly used for simulation of control strategies and performance. In order to be able to study gearshifting comfort, Volvo has an interest in developing new models for SimPow.

This project aims at investigating if the use of UML as a support to small-scale development ofan embedded system is relevant. The investigation is conducted by using UML during the initialphase of the development ofTelfafill, a filling machine by the company ?Telfafill AB?. The aimof the development of Telfafill is to separate the user interface from the control unit. In additionto this main objective, Telfafill AB would like possible changes to, and additions of,functionality of the filling machine to be investigated.Within the boundaries of this project, the development of Telfafill reached a full requirementspecification of the proposed system, and contact was made with potential external developers.No prototype construction had been started when the project ended.

Bakgrund: I och med att Basel II har instiftats i Sverige så måste finansiella institutioner beräkna sin marknadsrisk på sina portföljer. Detta kan göras genom olika VaR metoder. Dessa ger dock olika uppskattningar på marknadsrisken. De finansiella instituten får använda sig av den metod som de anser reflektera marknadsrisken bäst. Det finns dock ingen metod som utsetts till standard.Syfte: Syftet med detta arbete är att jämföra olika VaR-metoders skattning av marknadsrisken utifrån verkligt utfall, för att urskilja vilken metod som är funktionsdugligast.Avgränsningar: Denna undersökning inkluderar fyra olika VaR metoder.

One of the main tasks of the Swedish Armed Forces over the past few years has been International assignments, which increased the importance of the Lessons Learned process. Methods of simulator training with computers have become more frequent and the technical ability to collect digital data from sensors has been developed as well. This work demonstrates how the experience of Lessons Learned can be communicated with the computer simulator StriSimPC and how modern technology in future support experiences from the Lessons Learned process at the tactical level in the Army.Currently knowledge sharing consists of several processes and strategies in the Swedish Armed Forces. This is done by written reports, oral presentations and different practical exercises.This case study shows the functions of the simulator StriSimPC, methods of training and how it is used today. The study also describes the future opportunities, where digital metadata acquired from the modern combat vehicles could contribute sharing of experience in the Lessons Learned process.The summarized conclusions indicate that StriSimPC can combine the two strategies for personalization and codification of knowledge transfer to reach a higher level of learning.

AbstractSAAB has for a long time used user controlled pilot models in ARES. ARES is a simulation tool used in the desktop environment for simulations and calculations of the JAS 39 Gripen fighter and other aircraft. ARES stands for ?Aircraft Rigid body Engineering Simulation?. To work with these pilot models has been both time-consuming and inefficient.

Sammanfattning ?Entreprenörskap genom brädspel?Nivå: Kandidatuppsats i Innovation - 15 HPInstitution: Akademin för Innovation, Teknik och Design (IDT)Författare: Linus Linder & Robin Karlsson-HolmTitel: Entreprenörskap genom brädspelHandledare: Erik LindhultNyckelord: Entreprenörskap, Entreprenöriellt lärande, Spel, Simulation och InnovationForskningsfrågor: Hur kan utformning av ett entreprenörskapsspel för gymnasieelever som ska driva UF-företag se ut?Syfte: Syftet med studien är att utveckla ett entreprenörskapsspel som genererar kunskaper i entreprenörskap.Metod: Författarna har genomfört en kvalitativ studie som har haft parallella metoder för insamling av förstahandskällor. Dels i form av semi-strukturerade intervjuer med informanter och sedan i en mer experimentell metod, aktionsforskning. Genom att använda kvalitativ metod och semi-strukturerade intervjuer skapar författarna en bättre helhetsbild av studien.Slutsats: Efter arbetets gång har författarna utvecklat ett entreprenörskapsspel för gymnasieelever som ska driva UF-företag. Spelet har anpassats efter Ung företagsamhets processmodell för att ge elever kunskaper och erfarenheter som dem kommer ha användning för vid UF-företagande.

AbstractWith increasing population and increasing demands for comfort and thus an increase in energy demand, it is necessary to examine various energy-efficiency measures. This work deals with the ability to control the flow through the heating system to achieve the desired comfort with as little energy as possibleA heating system contains of different parts, roughly speaking, you can divide it to three main components: Heat source, Distribution and Heat emitters. All components are working together to bring heat to the building. What is examined in this report are different ways of adjusting the flow and supply temperature and how it affects comfort and energy use in a building.At today ?s date the conventional method is to use a high flow through the heating system, which affects pressure drop and cooling of the fluid.

SAMMANFATTNINGIntroduktionKommunikationen i ett vårdteam har stor betydelse för samarbetet kring en skadad patient. När kommunikationen brister kan det leda till sämre omhändertagande av en traumapatient. Ledaren för teamet har en betydande roll för teamarbetet. På Försvarsmedicincentrum i Göteborg tränas teamen med medicinsk simulering med fokus på teamarbete.SyfteSyftet var att undersöka hur kommunikationen erfors och påverkade samarbetet inom teamet under en medicinsk simuleringsövning.MetodFokusgruppintervjuer genomfördes av teamen efter en övning i medicinsk fullskalesimulering. Frågorna var semistrukturerade.

An energy study has been performed on two blocks in an area called Gävle Strand. The buildings are owned by a tenant-owner?s association called brf Carolina and were built by the company Skanska 2008. The builder as well as brf Carolina are pussled by the fact that electricity use is higher than expected while heating is less. Skanska is also very interested in finding out how much heat recovery from stale exhaust air through a geo-thermal heat pump is contributing to the general heating requirement and energy balance in four out of the ten buildings located on the properties.To find possible answers to the higher electricity use a literature survey on user behaviour was conducted.

Då många företag vill skaffa sig marknadsandelar genom att leverera rätt produkt, vid rätt tid och för rätt kostnad har de börjat arbeta med Simuleringsdriven Konstruktion. Simuleringsdriven Konstruktion hjälper dem att genom ett iterativt arbetssätt hitta optimal konstruktion tidigt i NPD-processen och därigenom reducera tid och kostnad för produktutvecklingen.Många företag som sysslar med forskning och utveckling kräver idag mer av provutrustning än tidigare för att kunna kontrollera och möta ökande krav på produkter.  Mer sofistikerad provutrustning behöver utvecklas för att möta ökade krav på produktprov. Krav så som säkerhet, kapacitet, tidseffektivitet, noggrannhet etc. Att även tid och kostnad för utveckling av provutrustning reduceras är viktigt.Detta examensarbete har syftat till att ta fram riktlinjer för effektivisering av arbetet med Simuleringsdriven Konstruktion i utvecklingsprocesser.

An energy study has been performed on two blocks in an area called Gävle Strand. The buildings are owned by a tenant-owner?s association called brf Carolina and were built by the company Skanska 2008. The builder as well as brf Carolina are pussled by the fact that electricity use is higher than expected while heating is less. Skanska is also very interested in finding out how much heat recovery from stale exhaust air through a geo-thermal heat pump is contributing to the general heating requirement and energy balance in four out of the ten buildings located on the properties.To find possible answers to the higher electricity use a literature survey on user behaviour was conducted.

There is a great need to reduce nutrient leaching from arable land into lakes and oceans. By using several different types of models it has previously been possible to describe nutrient losses in a catchment area with a minimum unit of sub-catchment level. At present, it is instead desirable to model a smaller catchment with an opportunity to re-connect the results to the corresponding fields in the catchment. Such models already exist but they are not fully able to properly describe Swedish conditions and land characteristics in our region.With the approach of creating such a model, SLU has developed a project with this work as its first stage. The model is expected to be created under the working name SWE-model which stands for Soil Water Environment and is in this first stage supposed to apply the SOIL model in catchment scale. During the procedure to describe the first step in the process of developing such a model adapted to Swedish conditions and which works in the catchment scale with an area of about 10-30 km2, focus has been set on calculating the transport of water flow from different hydrological response units. Regardless of the processes occurring in the soil after the water has been added, it is assumed that all the water which flows from each simulated unit is drained.In the first step the hydrologic response units were identified based on land use and soil type in the study area. With the help of a script with functions that retrieve and transform data, certain units were chosen for simulation. The script was also created in this project. Finally, the model results were aggregated and summarized for each unique unit, for each sub-catchment, and also for the whole catchment.From the results it is possible to see similarities in the flow dynamics between modeled and measured data. The efficiency coefficient has been calculated to correspond to the mean of the measured values for the whole simulation period. With an automated calibration process the model should be able to perform better. The volume error gives an indication of overestimation from the model..

The borehole heat exchangers of today suffer from poor thermal and hydrodynamic performance. The purpose of this thesis is to improve the performance of ground source heat pump systems and thermal energy storages by increasing the energy efficiency of the borehole heat exchangers. For this reason, the annular coaxial borehole heat exchanger (CBHE) has been analyzed. This type of heat exchanger is interesting in terms of both thermal and hydrodynamic performance. A model has been set up in the program Comsol Multiphysics in order to investigate the heat transfer characteristics along the borehole.

Severe floods caused by heavy autumn rains in year 2000 raised the question whether measures to reduce the damage from high water levels, in the area surrounding lake Glafsfjorden and along the river Byälven down to lake Vänern, are possible. One option is to reduce flow resistance along the river and thereby lower the maximum water level a given inflow would cause. Good knowledge of hydraulic and hydrological conditions is necessary in order to estimate the effect of such flow-reducing measures. In order to quantify such effect a 1-dimensional hydraulic flow model has been set up for the river Byälven using the software package MIKE 11. The model is more detailed, especially concerning topography and bathymetry, than earlier models used for studies of the river.