This is the project of making a stage design for Batboy ? the musical, a cooporation with a network of musical artists. The aim of the project was to create a space on stage that strengthens and expands the experience of the story told, and find design solutions that give an extra dimension to the story. The prerequisites for my work were partly defined from the produc¬tion, as were my limitations. In the cast of ten artists some were to play more than one role, often one of the opposite sex.

Tallen (Pinus Sylvestris L.) är för den svenska skogsindustrin ett av de viktigaste trädslagen. Tallens kvalitet är påverkbar genom röjning, där röjningens intensitet och tidpunkt är avgörande för tallens diametertillväxt, årsringsbredd, kvistdiameter, krongränshöjd, stamform, juvenilvedsandel och elasticitetsmodul. Röjningsarbete utförs via olika röjningsformer, där röjningsformerna enkelställning, toppröjning, stråkröjning och korridorröjning används i svenskt skogsbruk. Studien syftade till att utreda om det fanns signifikanta skillnader i behandlingseffekt på tallens medelhöjd, medeldiameter, kvistdiameter, krongränshöjd, höjd/diameter-kvot, elasticitetsmodul och årsringsbredd mellan röjningsformerna enkelställning, toppröjning, stråkröjning och korridorröjning. Studien syftade även till att utreda om ovanstående röjningsformer hade haft effekt på sambandet mellan elasticitetsmodul och årsringsbredd, i enskilda årsskott.Det studerade försöket anlades år 2003 i tallungskog i Umeå, Västerbottens län.

At the beginning of 2011, Sweden started using the European rules for structural design, the Eurocodes, instead of the previous national rules. In both the previous rules and the Eurocodes, it is possible to dimension concrete columns using tabled values. However, the required cross section measurements have increased considerably. Moreover, it is possible to dimension concrete columns using calculations, however, this is unusual.The development of a fire in a fire cell can be divided into the growth stage, the fully developed fire and the cooling phase. The duration of each phase, as well as the temperature, is dependent on a number of factors, e.g.

The following report comprises my bachelor´s thesis in Industrial design, 30 hp. It is executed in collaboration with Bonum senior housing, who has been the client and assignment- maker of this project.The goal was to design a bench for their entrances, which could represent not only the needs of the target group but also Bonum as a trademark. The work is done with great care for both human kind and the environment, with sustainability as beacon.The design process has been followed.Initially, you will find the definition of a bench for entrances, the framework including inclusive as well as sustainable design, a function- and market analysis followed by the inspiration part of the project. Getting to know the target group and their specific needs has been essential for this work.Investigations about what senior house living and senior products are and what the target group thinks and feels, has been done. As a result, two ?personas? has been developed.With the help of a purposely chosen group of people, surveys and ergonomic studies has been executed, as well as prototype-testing.The fact-finding has formed the stable and unavoidable foundation of this project, which later on gets more creative and idea based.

Today many buildings and it´s nearby surroundings are designed to achieve some kind of environmental goal.The issue concerning energy consumption is currently at focus and it is relevant that we start increase the share of renewable energy. Solar energy is an infinite resource and should therefore be considered when selecting an energy supplier. Uppsala University hospital is facing major restructuring when parts of the existing buildings will be refurbished and a large new building will be constructed. White Architects have developed a study concerning the new building and for some of the existing buildings on the hospital campus. Uppsala County requires tough energy measures and wants the new building to be classified as an eco-building in Whites following work. The classifications will involve high energy source requirements. This work has been conducted to see if solar power can be envisaged as a supplementary energy source for the University hospital and also to investigate the aesthetic impact of solar cells on the new building.

Flooding events are no longer rare, floods occur all over the world. Accordingly, it is vital for the society and different authorities to work with flood mapping. To meet the goal of Uppsala kommun to map the risks of floods in Uppsala län, a map of the different areas around Funboån which are inside the area of risk for flooding have been developed.In the work, cross sections and the water flow have been measured. Moreover, an echo-sounding have been carried out in Funboån to map the bottom topography. From the bottom map and laser scanned data covering the study area, a terrain model was created.

In this report a system for Rapid Control Prototyping, RCP, is evaluated through animplementation of the motor control methods Field Oriented Control, FOC, and Space VectorPulse Width Modulation, SVPWM. The evaluation emphasizes on time-consumption andresource utilization on the used hardware and on usability for of software.A new mechatronic laboratory is under development at ABB Corporate Research in Västerås. Itwill be used for both mechanical and motion control design using existing and new hardware.The control structure in a traditional robot system will be interfaced to a rapid prototypingsystem which should allow easy changes to algorithms at different levels in the system.The system designated for this project comes from National Instruments and constitutesLabVIEW Real-time and FPGA module as the software tools. The hardware is a NI Single-Board RIO (Reconfigurable Input Output), sbRIO, development board including a Field-Programmable Gate Array, FPGA, from Xilinx and a microprocessor from FreescaleSemiconductor. Graphical programming is performed in the LabVIEW environment, andthrough Xilinx tools the LabVIEW FPGA code is compiled to VHDL code.A pre-study was carried out to clarify the concept of RCP and investigate different systems forRCP and their traits.

This thesis for the Master of Science degree was performed at Oppunda Electronics AB. The assignment was to further develop an existing prototype of a dispensing equipment. The dispensing equipment doses a kind of glue, bonding which dentist use to mend teeth. The dispensing equipment is adjusted to dose 12 micro litres of bonding. With the dispensing equipment SafeBond Electronic the user can reduce the bonding consumption with approximately 50 percent.

The present study concerns a concept development of a product idea that Bengt Magnuson, associate professor, had when a heavy storm caused a widespread power failure of long duration. With a basic power-producing unit one should be able to get through a power loss. The product could also be useful for other tasks if different modules are connected, e g grass mower or snow-blower.According to the product idea the basic unit will be able to produce electric power enough for a fridge, freezer, TV, and a few electric lamps. Normally the basic unit can be used e g as a mower, when such a module is attached. An increased number of tasks would make the contraption useful and tempting for those who do not own an electrical power set in reserve.

The energy that the earth receives from the sun hourly has potential to cover a year?s energy demand in the world. Further, this type of energy is environmentally friendly, natural and free of cost. This report covers solar energy in an urban environment and consists of a case study of installations of photovoltaic cells in a part of the city of Stockholm. It is mainly the economic aspects that are covered but there is also a discussion about the practical consequences and the sustainability as a result of integration of solar energy in an urban environment. The aim of the study is to present results from economic calculations for utilization of solar energy in chosen buildings in Kungsholmen in Stockholm.

It always has been a need for the abiltiy to create color proofs. When an error occurs late in the production process, itis allways complicated and difficult to correct the error. In this project, digital proofs been made and discussions havebeen held with several people in the printing industry, in order to examine how well excisting digital proofs, meet thedemand of the market. And how close the digital proofs can come to the actual printsheat from the press. The study hasbeen shown that the one thing that has had the most influence on the outcome for the quality of a digital proof, is theprintshop operator?s knowledge about color management and proofing systems.

A Biogas plant in SLU?s (Swedish University of Agricultural Sciences) management sustains to behave in con-nection with the new animal stables at Lövsta. There will primarily manure from stables that rot to biogas. The biogas plant will also have the capacity that rot others substrates that can arise in the farm operation. The aim with the biogas plant is to produce non fossil electrical and gas heat for own customs, to reduce smell impact from stables and to make possible different types of research investments within the area.This study has implemented multiple cases study of different investment scenarios.

This Master of Science thesis was a part of Pharmadule Emtungas project to construct a mobile automated cell for welding of carbon steel pipe (Heating, Ventilation and Sanitation). Pharmadule Emtunga is using a modular building concept for building pharmaceutical factories. The modules contain these pipes. The goal of the thesis was to present concepts for technical solutions regarding welding methods and fixtures for the cell. Conceptual models for the cell were made with aid of CAD software.

This thesis work was made for Södra Cell Mörrums bruk in Blekinge. The purpose of the work was to develop a computer model in the simulation program Extend for the removal and balance of organic oxygen consuming substances, measured as COD (Chemical Oxygen Demand), in the new biological treatment plant in the mill. The plant produces two different pulp products, TCF- (Totally Chlorine Free) pulp and ECF- (Elementary Chlorine Free) pulp, for sale. The different bleaching procedures affect the characteristic of the wastewater and thus the effectiveness of the biological treatment plant.In the model that was developed the COD in the wastewater was divided into five different COD-fractions: soluble easily degradable (SS), soluble hardly degradable (SR), soluble inert (SI), particulate inert (XI) and particulate biomass (XB). To create the model FlowMac? was used as a base.

This thesis is a part of the DySCAS (Dynamically Self-Configuring Automotive System)project which has the overall purpose of creating a middleware for the electronics in an automotive environment. The thesis has been made with collaboration with ENEA AB who is a member of the DySCAS project. ENEA AB has developed a demonstration platform to test the fundamental ideas which the DySCAS project is built on.The purpose of this thesis was to design and implement a GPS application to be added to the demonstration platform. This was done by adding a GPS receiver to the original DySCAS demonstration platform and designing and implementing an application to be able to extract the information from it. The resulting application is able to present cur- rent position and absolute time to the DySCAS networks as services to be used by other applications or by the network it self.