Flooding events are no longer rare, floods occur all over the world. Accordingly, it is vital for the society and different authorities to work with flood mapping. To meet the goal of Uppsala kommun to map the risks of floods in Uppsala län, a map of the different areas around Funboån which are inside the area of risk for flooding have been developed.In the work, cross sections and the water flow have been measured. Moreover, an echo-sounding have been carried out in Funboån to map the bottom topography. From the bottom map and laser scanned data covering the study area, a terrain model was created.

A piezoelectric injector was modeled, in this Master Thesis Project which was carried out at Scania CV AB in Södertälje, in GT-Fuel. GT-Fuel is simulation program from Gamma Technology.The simulation model for the piezo injector was divided into a hydro-mechanical system and an electrical system (Piezoelectric element). First the hydro-mechanic model was duplicated from Advance Continuous Simulation Language model (ACSL). The simulation results were then compared to the ACSL, to verify that the hydro-mechanical system was modeled correctly. The simulation results for the electrical model were also compared with a Simulink model.

This master thesis consists of the creation of shock absorber models for percussive rock drills. A model of the rock was also developed. These models were connected to existing models of the rock drill to create a complete simulation of the rock drilling process.When the models had been created the rock model was evaluated by comparison with measured values from lab tests. The verified rock model was then used to evaluate the shock absorber models.Four new shock absorber concepts have been developed. Three of these have been modelled, while the fourth have only been sketched and described.The evaluation of the models showed the following:? Simulations of the single shock absorber don?t correlate to reality very well.

This thesis aims to present the essential background on how to perform climate changeimpact assessments, and to present the results from a climate impact assessment on waterbalance and nitrate leaching for an arable Swedish soil. The soil is a sandy soil in southwesternSweden, grown with spring cereals. This study is meant to be a benchmark example,and cannot be seen as a regional or national assessment for Sweden, rather as an approachto present and analyze the most important parts of these kinds of assessments.A dynamical simulation model (COUP, Jansson and Karlberg, 2004) was used for thisstudy. The model was parameterized and calibrated against data from an experimental site,located in Mellby in Hallands county, south western Sweden. Measurements were carriedout between 1st of April 1988 and 1st of April 1991.

Numerical simulations play a vital role in both static and dynamic stability assessment of electric power systems and the foreseeing of voltage collapse. Simulations performed by Svenska Kraftnät(SvK) are mainly done in the specialized voltage collapse predicting software tool, SPICA and the more all?purpose software tool, ARISTO.The grid operators at SvK use SPICA to predict the maximum transfer limit at specified sections (in this report the section in concerns is the southern part of Sweden i.e. interface1 4). SPICA is mainly used as an online application by using actual states from the grid, these states update every quarter of an hour.This thesis is a continuation of the master thesis SPICA ? ARISTO JÄMFÖRELSE by Jakob Katzman and Johan Fält.

In the spring of 2014 Sweco Systems AB were commissioned to design a ventilation system for a newly built preschool in Linköping. Terms from the client was that it cost efficiency would cope with the energy demands that are placed on the building. The unit chosen was a cross-flow heat exchanger, and this work is to compare it with two other heat exchangers to see if a more energy and cost efficient could have been chosen. The heat exchangers that was chosen for the comparison was a rotating- and a counterflow heat exchanger. Simulations have been made to the different heat exchangers by the manufacturers.

The aim of this thesis was to investigate if the robotized welding method FSW (Friction Stir Welding) could be applied for joining a rotating structure in an aero engine at Volvo Aero Corporation. FSW is expected to introduce less defects than today?s welding methods and could therefore be suitable for critical aero components. The material is the nickel based alloy Inconel 718, however a material experimentation is outside the scope of this report.The main goal of this study is to verify if the ESAB ROSIO robot based FSW-system has a suitable work space to be able to weld the rotating structure, and if the welding tool has accessibility to the joints. The FSW-process needs a rigid fixture, and a number of fix-ture concepts are presented based on a proposed weld sequence.

This thesis aims to present the essential background on how to perform climate changeimpact assessments, and to present the results from a climate impact assessment on waterbalance and nitrate leaching for an arable Swedish soil. The soil is a sandy soil in southwesternSweden, grown with spring cereals. This study is meant to be a benchmark example,and cannot be seen as a regional or national assessment for Sweden, rather as an approachto present and analyze the most important parts of these kinds of assessments.A dynamical simulation model (COUP, Jansson and Karlberg, 2004) was used for thisstudy. The model was parameterized and calibrated against data from an experimental site,located in Mellby in Hallands county, south western Sweden. Measurements were carriedout between 1st of April 1988 and 1st of April 1991.

A current conveyor is an active building block that can be used to implement most active and passive components. It differs from the operation amplifier in that it uses current instead of voltage. The current conveyor also has significantly higher voltage gain over a broader frequency range. To simplify the construction of analogue circuits and increase the construction efficiency it is desirable to use a top-down methodology. This means that the whole system is partitioned into a hierarchy of subsystems.

A growing number of cities and municipalities in Sweden begin to work with city models in 3D. For the most part the models are used for visualizations of ongoing planning processes, but also for the analysis of noise, shadow studies and environmental disaster simulations.Gothenburg continues to develop the use of 3D maps in municipal operations and is demanding a way to create building elements (walls), which generates in 3D buildings, from roof constructions that are mapped from the primary map. A method has been investigated in the present study. The results are then presented as a 3D model of buildings, along with a terrain map that will facilitate the localization of the area. The created 3D buildings are then compared with roof-data from the primary map to see how well they harmonize with each other.

The thesis deals with three document retrieval models based on logic: the Boolean model,the fuzzy model and the Van Rijsbergen model.In Chapter 1, the author presents the purpose of the thesis. This is to give the logical foundationof the models, to describe them and to examine them critically. In Chapter 2, some importantnotions in document retrieval are presented. Chapter 3 is devoted to the Boolean model, Chapter4 to the fuzzy model and Chapter 5 to the Van Rijsbergen model.These three chapters are organized in the same way. First, the logical foundation of the modelis given.

This master thesis is made of two parts. The first part concerns the method and results ofdesigning a motion control system for a piece of research-equipment called BIRGIT. Theequipment is made to be used for research on eyemovements. In the second part, a computermodel of a part of the balance organ in the inner-ear is developed. The work has been done atthe Bernadotte laboratory at S:t Erik Eye Hospital.The equipment the control system is made for is a so-called rotationchair.

This master thesis covers the seasonal planning of a small scale hydropower system. The system in this study is owned and operated by Mälarenergi Vattenkraft AB. The total system consists of 4 different main rivers with 24 hydropower stations and several dams. The total installed power in the system is 43.75 MW. Most of the hydropower stations are regarded as small scale hydropower stations and thus entitled to green certificates.In this report the issue of planning is formulated as an optimization problem.

The aim of this thesis was to investigate if the robotized welding method FSW (Friction Stir Welding) could be applied for joining a rotating structure in an aero engine at Volvo Aero Corporation. FSW is expected to introduce less defects than today?s welding methods and could therefore be suitable for critical aero components. The material is the nickel based alloy Inconel 718, however a material experimentation is outside the scope of this report.The main goal of this study is to verify if the ESAB ROSIO robot based FSW-system has a suitable work space to be able to weld the rotating structure, and if the welding tool has accessibility to the joints. The FSW-process needs a rigid fixture, and a number of fix-ture concepts are presented based on a proposed weld sequence.

The aim of this essay was to study the nitrogen flow in two willowplantations, at different locations in the south of Sweden, that wereirrigated with sewage. The study was also performed to compare thedifferences in nitrogen flows between two years, 1998 and 1999. The studywas made in three parts. First, the denitrification activity was measuredusing the acetylen inhibition method. Second the nitrogen flow, as well asthe water- and heat flows, were modeled through the SOIL-SOILN-modelThird; the nitrogen flow was calculated to compare with the results fromthe model.The results from the measurements were then compared with the resultsfrom the SOILN-simulations to detect differences in the denitrificationrate.