This master thesis was initiated with the aim to answer at what level of installed capacity of wind power in the northern parts of Sweden it would be beneficial to improve the transmission capacity from the northern Sweden. During the process of this work the aim has changed to try and create a model that can be used to analyze how well the hydro power installed in the northern Sweden can even out the quick changes in wind power production.To create a good model of all hydro power in northern Sweden is a very large job, unfortunately too large for a master thesis. This report therefore ends with an extensive analysis of the simplifications that have been made and their effects as well as a list of the future work that has to be done.The model that has been created have shown to be effective and produce good results. The conclusions that can be made is that the northern Swedish hydro power have very good possibilities to balance the wind power production. Only a few cases where water have been spilled even though there has been some free capacity has been discovered.

After the tsunami disaster in December 2004 many arguments were heared that one oft the major reasons behind the poor Swedish effort connected to the evacuation and health care of the Swedish citizens in Thailand right after the incident is the Swedish model with independent government authorities. By comparing the constitution, the political decision making tradition by the ministers and the handling of the catastrophe in the tree Scandinavian countries Denmark, Norway and Finland, plus analysing the behaviour of the Swedish foreign and prime minister from a rational choose inspired individual decision making theory the research shows that there is no proof that a constitutional change in Sweden into the traditional model with government authorities controlled by the ministers alone would led to a more effective crisis handling by the government due to crises concerning Swedish citizens out states. Although the research shows that the constitution and the tradition of decision making in the government provides the basic condition of the ministers individual rational decision making.

This master?s thesis describes the development of a model of the catalystsystem aiming at control by an MPC. A well functioning model, which is suitable in control purpose, is important while emission legislation become more and more hard to fulfill for the car manufacturers. Much research has been done in the field of physical modeling of the system, but in this work a linear adaptive time discrete ARX-model is developed and validated.The systems tendency to change its dynamic during usage implies that the model must be adaptive. The developed model proved to be well functioning and shows promising conditions for the MPC design.

The aim of this thesis is to improve the control of urea injection at the combined power and heating plant Framtidens Gärstad (FTG). Tekniska Verken i Linköping AB is the owner of the plant.The FTG plant consists of a boiler where garbage combustion is done. From the combustion nitrogen oxides are emitted. These nitrogen oxides are hazardous to the environment. To reduce the nitrogen oxides, injection of urea into the boiler is used.

The situation at Plastal AB is following; the plant in Simrishamn has not capacity enough but the plant in Kristinehamn has unused capacity. My task with this master thesis is to build a logistic flow between this two plants, optimize purchase quantities and ensure delivery safety.The production of the Intermediate Section (LS) will be divided between the plants. The LS will be produced in the following way; the injection moulding process will be done in Simrishamn and the assembling and lacquering processes in Kristinehamn, The reason to divide the production is to ensure delivery safety. Plastal AB can not move the whole production of the l.S because the two plants have different processes (moulding res. injection moulding).When the 1.5 has been transported to Kristinehamn following moments are included in this order; lacquering, welding and assembling.

This thesis is a feasibility study into how Fresenius Kabi may rationalize their destruction process in regards to cost, recycling, and work environment. The two main objectives are to identify scrap flows and the possibility to improve or replace the equipment that is now carrying out the physical scrapping. The flow has been visualized by a flow chart of the material and communication. A chart of the problem established to visualize where improvements are necessary. Based on the problems proposals are presented on how to improve the flow thru the plant.During analyze of the physical scrapping equipment it was also necessary to take a deeper look at how they are carrying out there work today, how does the procedure look like, working environment and where are the weaknesses.

Drinking water is produced from raw water and is either from groundwater or surface water. This thesis aims to find out if the cleaning process of raw water is sufficiently effective. This is important because consumers are otherwise at risk of waterborne infection caused by pathogens. There are three groups of pathogens; bacteria, virus and parasite. These have different characteristics which mean that they require different water treatment to be separated.

The purpose of this thesis is through a case study and a survey; to examine the most appropriate communication channels between a sender and a receiver. It also aims to make this relationship more effective.The following questions are to be answered:1. Which communication channels ought to be used to optimize the message from Skara Näringslivsoffensiv to its target group?2. Which communication channels is Skara Näringslivsoffensiv planning to use?3.

Drinking water is produced from raw water and is either from groundwater or surface water. This thesis aims to find out if the cleaning process of raw water is sufficiently effective. This is important because consumers are otherwise at risk of waterborne infection caused by pathogens. There are three groups of pathogens; bacteria, virus and parasite. These have different characteristics which mean that they require different water treatment to be separated.

Risk management is a key competency that is constantly being researched how it can be improved within project management. The risk management process consists of four major steps: identify risks, assess the risks? significance on the project, evaluate and address the key risks and follow up.The majority of companies seem to neglect certain identified risks, and decide not to mitigate if the risk does not cause adverse effects to the business. To counteract undesirable consequences and help organisations to become more effective at managing risks an initial work has been conducted for a risk repository.The project develops a proposal on the design of a risk repository which aim to effectively support a database implementation. The study includes literature studies which resulted in a relational model for database implementation.

The aim of this thesis is to examine the properties of the municipalities in Sweden that influence the choice of being a certified Fairtrade city. The independent variables which are used in the statistical analysis are municipal governance, local tax rate, whether there is an university and/or university college in the municipality, average income and higher education in the municipality. The variables are examined by logistic regression. Since there are no statistical data on ethical procurement, this exogenous variable isn?t included in the regression.

The building and plant sectors represent a large part of Sweden?s energy use. Putting energy requirements in public procurement as a tool for reducing energy consumption in the building and plant sectors is therefor an opportunity that operators can take advantage of. The aim of this thesis was to map the energy requirements in procurement that operators in the public sector use today in building and plant projects. The analysis was made with respect to if the energy requirements corresponded to the parts with large energy use in building and plant projects and also in which way energy requirements in procurement are written in the contract.

The river Göta Älv reaches between Vänern and Gothenburg and is the main raw water source for Gothenburg that supplies about 700 000 people with water. To protect and maintain a high water quality, continuously samples and water analyses are made throughout the river. In 1998 a protection area was founded between surte and Lärjeholm where the raw water intake is. This was made to increase the awareness of the importance to protect the water. However, there is a lot of contribution of untreated stormwater to Göta Älv within the protection area.Göteborg Water and Sewage Works commissioned this thesis where two areas, Tagene industrial area and Kärra residential area, with untreated stormwater outlets within the protection area are studied.

In this study potential health risks for employees in connection with handling of bottom ash and bottom ash water at a Municipal Waste Incineration (MWI) plant have been investigated. Air surrounding the bottom ash and the bottom ash water has been examined. MWI is one of the primary ways to manage solid household waste, and bottom ash is the main solid residue produced by the incineration process. Bottom ash constitutes about 15-20% of the original waste. The bottom ash is extinguished in a water bath (bottom ash water).The study was carried out in a MWI plant in Karlstad, Sweden.

This report describes a synchronous machine model with magnetic saturation in d-axis, neutralconnection and electrical exciter interface for the transient simulator PSCAD/EMTDC. It hasbeen designed and verified in comparison to the regular machine model in EMTDC.The performance of the model is very good when incorporating a linear as well as a saturatedmagnetising inductance. The dynamic deviation is only thousandths to ten thousandths perunit. By using a cubic interpolation of the saturation curve, the model gives a good representationof the saturation effect. The open source code implementation of the synchronousmachine model gives the possibility to easily adapt the model to specific requirements.The derived model makes it possible to simulate a synchronous machine with its excitationsystems, e.g.