When constructing a building, a number of aspects must be harmonized in order for it to fulfill requirements ? a building must fulfill requirements such a load-bearing, conservation of energy and a good indoor environment by means of, among other things, moisture proofing .Moisture problems in buildings can affect health negatively. As we are increasingly staying in indoors, demands on a good indoor environment are higher.This work starts with examining moisture problems in slab-on-ground solutions, and then links the various scenarios to moisture problems in a concrete slab of a real building. The building with moisture problems is located in Årby by in Borlänge and moisture damage was found in the slab at an apartment adjoining wall.By reviewing literature written within the field of moisture problem, making hand calculations and modeling in the program Comsol Multiphysics, judgments are made to find explanations as to why the rise of moisture occurred in the building in Årby by.Generally, the following guidelines may be used to reduce the risk of moisture problems in slab-on-ground constructions:Drying of construction moisture before laying the floor material.Using draining layer beneath the slab, to prevent capillary suction.Using insulation under the slab, partly for comfort and to establish the temperature difference between the ground and the concrete slab.Avoid direct contact between the wood and concrete, due to degradation and fouling smells that normally occurs.If necessary, use additional vapor barrier.In addition to the above, there are various methods for moisture-proof and moisture-monitoring by design or by the method ByggaF suited for the entire construction process various events..

The aim of this study was to map the prevalence of aeolian sand dunes in Västerbotten, northern Sweden to find dunes formed during earlier deglaciation phases, which was then preserved in cold-based conditions during the youngest stadial of the Weichselian glaciation. These preserved dunes were expected to be covered by a layer of till and have a rather faint morphology compared to dunes formed during the Holocene. Consequently, high resolution LIDAR-derived images from the Swedish mapping, cadastral and land registration authority (Lantmäteriet) was used to detect the dunes throughout an area covering most of Västerbotten, above the highest coastline and below the mountain range. The analysis resulted in several new findings of aeolian dunes compared to the findings in the quaternary soil map created by the Geological Survey of Sweden. Despite the fact some of the dunes at the LIDAR-derived image had a strange faint appearance, it was quickly evident during the fieldwork that the aeolian sand was not covered by till on any of the dunes visited.

This report deals with prefabricated bathrooms and the advantage, during the production process, they have compared to ordinary produced bathrooms.The work is done together with the building company JM. The common task is to investigate if the manufactures, in spite of standardized design can meet the concept of JM, i.e. high flexibility and adjustment towards the customer. In JM they are doubtful to the method, as they did not yet worked with prefabricated modules and think that the choises for the costumer will be limited.There will be a short resume of the progress of the bathrooms and its importance as sanitary and wellbeing.The recent problems with damage caused by damp in bathrooms. Have resultade in regulations.

The purpose of this thesis is to collect knowledge of techniques and materials for planning roofgardens. Gardens built on top of buildings is not a new phenomenon, already in the beginning of the century architects were experimenting with roofgardens. During the Modern Era roofgardens appeared as a part of the design and worked well together with flat roofs and the ideas of light, air and greenery. Today the most common kind of roofgarden is on a ground-level joist that hides parking or other underground functions. The most important difference between planning a roofgarden and a garden on the ground is the limitation of the load of the roofgarden. Plants, paving-material and equipment must be chosen with this in mind. A light and thin layer of soil demands plants with small needs for water and nutrition.

Until the beginning of the 1900:th century the paper making process was handicraft. The paper machines that have been developed since then are as impressing in size as fascinating when it comes to the technique. The process has always been improved to give a better paper for lower costs, with as short manufacture time as possible. Stratified forming has been a reality since 1830. From the beginning it was applied to board and paperboard.

Basal cell carcinoma (BCC) is the most common non-melanoma skin cancer. It can be divided in different subtypes. The most common type is superficial and is most frequently occurring on the trunk and on the face. In severe cases it can be difficult to differentiate basal cell carcinoma from other skin tumors, therefore a skin biopsy is conclusive diagnostic method. In terms of treatment, curettage is a common non-surgical treatment of basal cell carcinoma.

When constructing a building, a number of aspects must be harmonized in order for it to fulfill requirements ? a building must fulfill requirements such a load-bearing, conservation of energy and a good indoor environment by means of, among other things, moisture proofing .Moisture problems in buildings can affect health negatively. As we are increasingly staying in indoors, demands on a good indoor environment are higher.This work starts with examining moisture problems in slab-on-ground solutions, and then links the various scenarios to moisture problems in a concrete slab of a real building. The building with moisture problems is located in Årby by in Borlänge and moisture damage was found in the slab at an apartment adjoining wall.By reviewing literature written within the field of moisture problem, making hand calculations and modeling in the program Comsol Multiphysics, judgments are made to find explanations as to why the rise of moisture occurred in the building in Årby by.Generally, the following guidelines may be used to reduce the risk of moisture problems in slab-on-ground constructions:Drying of construction moisture before laying the floor material.Using draining layer beneath the slab, to prevent capillary suction.Using insulation under the slab, partly for comfort and to establish the temperature difference between the ground and the concrete slab.Avoid direct contact between the wood and concrete, due to degradation and fouling smells that normally occurs.If necessary, use additional vapor barrier.In addition to the above, there are various methods for moisture-proof and moisture-monitoring by design or by the method ByggaF suited for the entire construction process various events..

Dokumentet är ett resultat av studier gjorda under kursen Kandidatarbete I Datavetenskap. Arbetet utforskade, genom fallstudie, två egenskaper av distribuerade informationssystem och relation mellan dessa: säkerhet och prestanda. Målet med fallstudien har varit att belysa nackdelen med användning av Secure Socker Layer (SSL) dvs. dess effekt på hastigheten och fördelen med SSL, dvs. SSL:s roll i informationssäkerhetsarbetet.

A common problem in forestry is plant death caused by frost. The risk of frost is highest on wind protected, flat or low-lying areas in the terrain. Here you often have regeneration problems with Norwegian spruce which is especially sensitive to spring frost. Swedish tree experiments have shown that the black spruce can be a suitable alternative on these areas, for example on moisture frost prone areas. The species originates from North America and its pioneer tree characteristics make it more frost hardy than Norwegian spruce.

E-business innebär att företag använder Internetteknologier eller nätverksteknologier för att skapa större affärsnytta i deras affärsprocesser. För att kunna genomföra automatiserade affärsprocesser krävs att de olika system som används är interoperabla, d v s kan kommunicera och fungera ihop på ett effektivt sätt. Målet med Web Services är att skapa hög interoperabilitet, vilket gör denna teknik lämplig för e-business. Företag kan specialicera sig på att skapa specifika Web Services. Dessa Web Services kan sedan vara byggstenar åt andra företags tjänster. Det krävs då att Web Services kan integreras på ett bra sätt så att de verkligen bildar en affärsprocess. Därför är även frågor kring hur integration mellan Web Services ska gå till, viktigt ur ett e-bussiness perspektiv. Det vi kommit fram till är att det går att minimera integrationsproblemen genom att anvä nda de mest standardiserade protokollen och följa vissa riktlinjer vid skapandet av Web Services.

Purpose: The purpose is to examine more closely why the achievement of the environmental goals is so low. To within the thesis work to make this as interesting and with as good quality as possible, especially the environmental quality goal Reduced climate impact, but also Natural acidification and Protective ozone layer, has been chosen to be studied further. Method: A qualitative method and text analysis has been applied. Intervention theory, as Vedung 2009 describes, is used as an intellectual backbone and as a help to structure the essay. The three environmental quality goals correspond cases, or units of analysis. Analysis: The fulfillment of the respective environmental quality goals is analyzed according to its goal, policy instruments, implementation and its effects. To this some of the problems are analyzed that exist on the path to achieve the goals.

Deep litter is a system for animals kept in separate stalls, loafing and bedding in wind shelters. The litter can consist of different bedding, like straw and peat. The system is allowed to build over and to ensure optimal proportions it is necessary to add new straw regularly and to have good conditions. Important conditions are aerobic state, humidity, amount of organic substance and acceptable temperatures in the litter. The micro organisms are depending on temperature for their living conditions and to get the bottom layer in the litter to start burning.

I have through a case study looked on a milkingfarm in Dalarna and been counting on what it would cost to increase the silagestorage. Today they have to little capacity on the existing towersilo because they built a bigger farm with more cows. The reason is that two families decided to start having the production on one farm together and moved all animals from one of the farms to the other farm. So for that reason I have looked on the costs to build a new towersilo or levelsilo. The goal has been not only to look at the buildingcost but also which operatingcost that is included with the different alternatives. I have taken tenders from two different towersilocompany, Bjurenwall and Svenska Neuero and taken tenders from Abetong for a levelsilo with roof and one without roof. The overall feed requirements on the farm is on 240 tonnes dry extract and the old towersilo hold 110 tonnes dry extract so the need for a new foundation is on 130 tonnes dry extract. I have through cost estimate been counting on the specific buildingcost for each buildingaltenative.

The aim of this study is to describe how a theme about vitamins and analytical chemistry can be planed and implemented in a summer research school managed by AstraZeneca. The description of the theme is intended to be used as an instructor?s guide to upcoming summers-research-schools with the same theme. The students, which participated in the summer school of 2007, went to upper secondary school. During the summer school they were going to investigate the content of vitamin C in different fruits and vegetables.

Most of the portable electronic devices use a battery as a primary power source. Nowadays, when the applications are becoming smaller and smaller and more power efficient, the designer needs to concentrate more on reducing power consumption, using secondary power sources and introducing power storage devices. Multiple power source availability and a power storage device on the board will make the applications much more useful and efficient in everyday use. This thesis proposes a power supply unit (PSU) for wireless sensor platforms which is capable of supplying a sensor node with energy from multiple sources, as well as status information from the PSU. Present power storage devices, like electric double-layer capacitors (EDLCs) and batteries, have become more and more common as their characteristics have developed.